BS ISO 18084-2011 Press tools for tablets Punches and dies《药品的冲压工具 冲压机和模具》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 18084:2011Press tools for tablets Punches and diesBS ISO 18084:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 18084:2011. Itsu

2、persedes BS ISO 18084:2005 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to incl

3、ude all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 73925 5ICS 25.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy a

4、nd Strategy Committee on 30 September 2011.Amendments issued since publicationDate Text affectedBS ISO 18084:2011Reference numberISO 18084:2011(E)ISO 2011INTERNATIONAL STANDARD ISO18084Second edition2011-09-15Press tools for tablets Punches and dies Outillage de presse pour comprims Poinons et matri

5、ces BS ISO 18084:2011ISO 18084:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in w

6、riting from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO

7、18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Nomenclature . 1 4 Dimensions and tolerances 3 4.1 Punches 3 4.2 Dies . 9 4.3 Positioning of punch with key in relation to machine turret and tablet shape to be executed . 11 5

8、Designation 11 5.1 Designation of punches 11 5.2 Designation of dies . 12 6 Marking . 12 6.1 Marking of punches . 12 6.2 Marking of dies 12 7 Material . 12 Annex A (normative) Detail of punch head . 13 Bibliography 14 BS ISO 18084:2011ISO 18084:2011(E) iv ISO 2011 All rights reservedForeword ISO (th

9、e International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committ

10、ee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechn

11、ical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member

12、bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

13、any or all such patent rights. ISO 18084 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (ISO 18084:2005), of which it constitutes a minor revision. In particular, key item 5 an

14、d key item 34 of Figure 1 and detail X of Figure 7 have been corrected. BS ISO 18084:2011INTERNATIONAL STANDARD ISO 18084:2011(E) ISO 2011 All rights reserved 1Press tools for tablets Punches and dies 1 Scope This International Standard specifies the main dimensions, tolerances and characteristics o

15、f punches and dies for all kinds of tablets. This International Standard deals with measures which are relevant for the interchangeability of the press punches between the different tableting machines of various manufacturers. 2 Normative references The following referenced documents are indispensab

16、le for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individ

17、ual tolerance indications 3 Nomenclature See Figures 1 and 2. BS ISO 18084:2011ISO 18084:2011(E) 2 ISO 2011 All rights reservedKey 1 upper punch 2 lower punch 3 die 4 key 5 keyway 6 stem (tip to full barrel) 7 barrel-to-stem chamfer 8 cup depth 9 tip face 10 blended land 11 face 12 bore 13 die groov

18、e 14 protection radius or shoulder 15 chamfer or radius 16 outer diameter 17 tip straight 18 relief 19 barrel-to-stem radius 20 working length of the tip 21 overall length 22 barrel 23 working length 24 barrel-to-neck radius 25 neck-to-head radius 26 inside head angle 27 neck under head 28 head 29 h

19、ead outer diameter 30 outside head angle 31 head flat 32 key orientation angle 33 upper punch face key position 34 land Figure 1 Punch and die terminology BS ISO 18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved 3Key 1 punch 2 overall length 3 working length 4 depth cup 5 practical radius 6 n

20、ominal radius 7 land 8 tip face diameter Figure 2 Terminology related to tip face profile 4 Dimensions and tolerances 4.1 Punches 4.1.1 Upper punches 4.1.1.1 Upper punches without key The dimensions and tolerance of upper punches without key shall be in accordance with the indications of Figure 3 an

21、d Table 1. The dimensions and tolerance of punch head shall be in accordance with the indications of Annex A. 4.1.1.2 Upper punches with key The dimensions and tolerance of upper punches with key shall be in accordance with the indications of Figure 4 and Table 1. The dimensions and tolerance of pun

22、ch head shall be in accordance with the indications of Annex A. BS ISO 18084:2011ISO 18084:2011(E) 4 ISO 2011 All rights reservedDimensions in millimetres, Surface roughness values in micrometres General tolerance: ISO 2768-m Key 1 dust cup place aThe values of D, R and (133,6 f ) 0,01 shall be defi

23、ned by the user. bThe appearance of the cup radius and the land shall correspond to a polished mirror (i.e. 0,025 m Ra 0,10 m). cThe land (see Figure 2, key item 7) varies according to D and the tablet dimensions, and should be equal to: 0,05 for D 5 0,1 for 5 D 20 0,2 for D 20. dFor shape tooling,

24、the tolerance of all dimensions of the tip should correspond to f7 applied to the largest dimension. eThe values of L shall be subject to agreement between the manufacturer and the user. fx shall be subject to agreement between the manufacturer and the user. Figure 3 Upper punches without key BS ISO

25、 18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved 5Dimensions in millimetres, Surface roughness values in micrometres General tolerance: ISO 2768-m Key 1 dust cup place aThe values of D, R and (133,6 f ) 0,01 shall be defined by the user. bThe appearance of the cup radius and the land shall

26、correspond to a polished mirror (i.e. 0,025 m Ra 0,10 m). cThe land (see Figure 2, key item 7) varies according to D and the tablet dimensions, and shall be equal to: 0,05 for D 5 0,1 for 5 D 20 0,2 for D 20. dFor shape tooling, the tolerance of all dimensions of the tip should correspond to f7 appl

27、ied to the largest dimension. eThe values of L shall be subject to agreement between the manufacturer and the user. fx shall be subject to agreement between the manufacturer and the user. Figure 4 Upper punches with key BS ISO 18084:2011ISO 18084:2011(E) 6 ISO 2011 All rights reservedTable 1 Dimensi

28、ons of upper punches Dimensions in millimetres D1D2D3D4L1h6 00,100,1 0,2 00,219 15,8 25,27 9,6 20,7 25,35 22 31,6 16 27 4.1.2 Lower punches 4.1.2.1 Lower punches without key The dimensions and tolerance of lower punches without key shall be in accordance with the indications of Figure 5 and Table 2.

29、 The dimensions and tolerance of punch head shall be in accordance with the indications of Annex A. 4.1.2.2 Lower punches with key The dimensions and tolerance of lower punches with key shall be in accordance with the indications of Figure 6 and Table 2. The dimensions and tolerance of punch head sh

30、all be in accordance with the indications of Annex A. BS ISO 18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved 7Dimensions in millimetres, Surface roughness values in micrometres General tolerance: ISO 2768-m aThe values of D, R and (133,6 f ) 0,01 shall be defined by the user. bThe appearanc

31、e of the cup radius and the land shall correspond to a polished mirror (i.e. 0,025 m Ra 0,10 m). cThe land (see Figure 2, key item 7) varies according to D and the tablet dimensions, and should be equal to: 0,05 for D 5 0,1 for 5 D 20 0,2 for D 20. dFor shape tooling, the tolerance of all dimensions

32、 of the tip should correspond to f7 applied to the largest dimension. eThe values of L shall be subject to agreement between the manufacturer and the user. fx shall be subject to agreement between the manufacturer and the user. gThe value of the radius varies according to diameter D and the form. Fi

33、gure 5 Lower punches without key BS ISO 18084:2011ISO 18084:2011(E) 8 ISO 2011 All rights reservedDimensions in millimetres, Surface roughness values in micrometres General tolerance: ISO 2768-m aThe values of D, R and (133,6 f ) 0,01 shall be defined by the user. bThe appearance of the cup radius a

34、nd the land shall correspond to a polished mirror (i.e. 0,025 m Ra 0,10 m). cThe land (see Figure 2, key item 7) varies according to D and the tablet dimensions, and should be equal to: 0,05 for D 5 0,1 for 5 D 20 0,2 for D 20. dFor shape tooling, the tolerance of all dimensions of the tip should co

35、rrespond to f7 applied to the largest dimension. eThe values of L shall be subject to agreement between the manufacturer and the user. fx shall be subject to agreement between the manufacturer and the user. gThe value of the radius varies according to diameter D and the form. Figure 6 Lower punches

36、with key BS ISO 18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved 9Table 2 Dimensions of lower punches Dimensions in millimetres D1D2D3D4L1h6 00,100,1 0,2 00,219 15,8 25,27 9,6 20,7 25,35 22 31,6 16 27 4.2 Dies The dimensions and tolerance of dies shall be in accordance with the indications o

37、f Figure 7 and Table 3. BS ISO 18084:2011ISO 18084:2011(E) 10 ISO 2011 All rights reservedDimensions in millimetres, Surface roughness values in micrometres General tolerance: ISO 2768-m aOption tapered 1 % on 5 mm. Upon agreement between the user and the manufacturer, this may be different. bChamfe

38、r or radius, according to agreement between the user and the manufacturer. cFor shape tooling, the tolerance of all dimensions of the tip should correspond to H7 applied to the largest dimension. dOption with radius. eOption with groove. Figure 7 Dies BS ISO 18084:2011ISO 18084:2011(E) ISO 2011 All

39、rights reserved 11Table 3 Dimensions for dies Dimensions in millimetres N M H h6 0,1 h6 21 19,422,22 24 21,5 30,16 27,8 38,1 35,7 23,81 4.3 Positioning of punch with key in relation to machine turret and tablet shape to be executed The positioning of punch with key in relation to machine turret and

40、tablet shape to be executed shall be in accordance with the indications of Figure 8. Key 1 key position in direction of rotation of turret aDirection of rotation of turret. bTop view of lower punch. Figure 8 Positioning of punch with key in relation to machine turret and tablet shape to be executed

41、5 Designation 5.1 Designation of punches Punches according to this International Standard shall be designated by a) “Upper punch without key” or “Upper punch with key” or “Lower punch with key” or “Lower punch without key”; b) reference to this International Standard, i.e. ISO 18084; c) the punch di

42、ameter, D1, in millimetres. EXAMPLE An upper punch with key having a diameter D1of 19 mm is designated as follows: Upper punch with key ISO 18084 - 19 BS ISO 18084:2011ISO 18084:2011(E) 12 ISO 2011 All rights reserved5.2 Designation of dies Dies according to this International Standard shall be desi

43、gnated by: a) “Die”; b) reference to this International Standard, i.e. ISO 18084; c) the die diameter, N, in millimetres. EXAMPLE A die of diameter N = 21 mm is designated as follows: Die ISO 18084 - 21 6 Marking 6.1 Marking of punches Punches shall have marking which includes at least the following

44、 information: a) manufacturers identification; b) number of the punch in the series; c) identification number. 6.2 Marking of dies Dies shall have marking on one of the flat surfaces which includes at least the following information: a) manufacturers identification; b) number of the die in the serie

45、s; c) identification number. 7 Material The material and hardness are left to the manufacturers discretion. BS ISO 18084:2011ISO 18084:2011(E) ISO 2011 All rights reserved 13Annex A (normative) Detail of punch head The detail of the punch head is given in Figure A.1. Dimensions in millimetres, Surfa

46、ce roughness values in micrometres General tolerance: ISO 2768-m Figure A.1 Detail of punch head BS ISO 18084:2011ISO 18084:2011(E) 14 ISO 2011 All rights reservedBibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation B

47、S ISO 18084:2011BS ISO 18084:2011ISO 18084:2011(E) ICS 25.120.10 Price based on 14 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. I

48、t presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are update

49、d by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform th