1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58cylinders Part 1: Test pressure 6 MPa and belowICS 23.020.30Gas cylinders Refillable welded stainle
2、ss steel BRITISH STANDARDBS ISO 18172-1:2007BS ISO 18172-1:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2007 BSI 2007ISBN 978 0 580 50764 9Amendments issued since publicationAmd. No. Date Commentsrequest to its secretary.This pu
3、blication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementatio
4、n of ISO 18172-1:2007.The UK participation in its preparation was entrusted by Technical Committee PVE/3, Gas containers, to Subcommittee PVE/3/3, Transportable gas containers Cylinder design, construction and testing at the time of manufacture.A list of organizations represented on this committee c
5、an be obtained on Reference numberISO 18172-1:2007(E)INTERNATIONAL STANDARD ISO18172-1First edition2007-03-01Gas cylinders Refillable welded stainless steel cylinders Part 1: Test pressure 6 MPa and below Bouteilles gaz Bouteilles soudes en acier inoxydable rechargeables Partie 1: Pression dpreuve d
6、e 6 MPa et infrieure BS ISO 18172-1:2007ii iiiContents Page Foreword. v Introduction . vi 1 Scope . 1 2 Normative references . 1 3 Terms, definitions and symbols 2 3.1 Terms and definitions. 2 3.2 Symbols . 3 4 Materials and heat treatment . 4 4.1 General. 4 4.2 Categories . 5 4.3 Heat treatment. 5
7、4.4 Test requirements. 5 5 Design 5 5.1 General requirements. 5 5.2 Calculation of cylindrical shell wall thickness 6 5.3 Design of convex ends. 6 5.4 Minimum wall thickness. 9 5.5 Ends of other shapes . 9 5.6 Design of openings. 9 6 Construction and workmanship 9 6.1 General. 9 6.2 Welding procedur
8、es . 10 6.3 Cryoforming procedure 10 6.4 Welded joints of pressure-containing parts 10 6.5 Non-pressure-containing attachments.10 6.6 Valve protection 11 6.7 Neck threads . 11 6.8 Visual examination . 11 7 New design tests. 12 7.1 General requirements. 12 7.2 Verifications and tests 13 7.3 Descripti
9、ons of tests 13 7.4 Design testing certificate . 14 8 Batch tests. 14 8.1 General. 14 8.2 Information 15 8.3 Tensile test 15 8.4 Bend test 18 8.5 Macroscopic examination of weld cross-sections 20 8.6 Checks and verifications . 20 9 Tests on every cylinder 21 9.1 Pressure test . 21 9.2 Hardness test
10、21 9.3 Leakage test 21 10 Failure to meet test requirements . 21 11 Markings 22 BS ISO 18172-1:2007iv 12 Certificate. 22 Annex A (normative) Radiographic examination of welds. 23 Annex B (normative) Description and evaluation of manufacturing defects and conditions for rejection of welded stainless
11、steel gas cylinders at time of visual inspection 25 Annex C (informative) Examples of design and batch testing certificates. 27 Annex D (normative) Manufacturers markings for LPG 32 Bibliography . 33 BS ISO 18172-1:2007vForeword ISO (the International Organization for Standardization) is a worldwide
12、 federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that
13、committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in acc
14、ordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ
15、ires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 18172-1 was prepared by Techn
16、ical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 3, Cylinder design. ISO 18172 consists of the following parts, under the general title Gas cylinders Refillable welded stainless steel cylinders: Part 1: Test pressure 6 MPa and below Part 2: Test pressure greater than 6 MPa BS ISO 18172-1:200
17、7vi Introduction The purpose of this part of ISO 18172 is to provide a specification for the design, manufacture and testing of refillable transportable welded stainless steel gas cylinders with a test pressure up to 6 MPa (60 bar). The specifications given are based on knowledge of, and experience
18、with, materials, design requirements, manufacturing processes and control during manufacture of cylinders in common use. ISO 18172 has been prepared to address the general requirements in Section 6.2.1 of the UN model regulations for the transportation of dangerous goods ST/SG/AC.10/1/Rev.13. It is
19、intended to be used under a variety of regulatory regimes, but has been written so that it is suitable for use with the conformity assessment system in paragraph 6.2.2.5 of the above-mentioned model regulations. BS ISO 18172-1:20071Gas cylinders Refillable welded stainless steel cylinders Part 1: Te
20、st pressure 6 MPa and below 1 Scope This part of ISO 18172 specifies minimum requirements concerning material, design, construction and workmanship, manufacturing processes and testing of refillable transportable welded stainless steel gas cylinders, of water capacities from 0,5 l up to and includin
21、g 500 l, for compressed, liquefied and dissolved gases. This part of ISO 18172 is applicable only to cylinders manufactured from stainless steels with test pressures up to 6 MPa (60 bar). If required, transportable large cylinders of water capacity above 150 l and up to 500 l may be manufactured and
22、 certified to this part of ISO 18172, providing that handling facilities are provided (see 6.5.5). For acetylene service, additional requirements for the cylinder and the basic requirements for the porous mass are given in ISO 3807-1 and ISO 3807-2. 2 Normative references The following referenced do
23、cuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2504:1973, Radiography of welds and viewing conditions for films Utiliza
24、tion of recommended patterns of image quality indicators (I.Q.I.) ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric acid ISO 5817, Welding F
25、usion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) Quality levels for imperfections ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method ISO 6892, Metallic materials Tensile testing at ambient temperature ISO 7438, Metallic materials Bend test
26、 ISO 9328-7:2004, Steel flat products for pressure purposes Technical delivery conditions Part 7: Stainless steels ISO 9606-1, Approval testing of welders Fusion welding Part 1: Steels ISO 9956-1, Specification and approval of welding procedures for metallic materials Part 1: General rules for fusio
27、n welding BS ISO 18172-1:20072 ISO 9956-3, Specification and approval of welding procedures for metallic materials Part 3: Welding procedure tests for arc welding of steels ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic mater
28、ials ISO 11117, Gas cylinders Valve protection caps and valve guards Design, construction and tests ISO 13769, Gas cylinders Stamp marking ISO 14732, Welding personnel Approval testing of welding operators for fusion welding and of resistance weld setters for fully mechanized and automatic welding o
29、f metallic materials ISO 17636, Non-destructive testing of welds Radiographic testing of fusion-welded joints ISO 17637, Non-destructive testing of welds Visual testing of fusion-welded joints ISO 20807, Non-destructive testing Qualification of personnel for limited application of non-destructive te
30、sting 3 Terms, definitions and symbols For the purposes of this document, the following terms, definitions and symbols apply. 3.1 Terms and definitions 3.1.1 yield stress value corresponding to 0,2 % proof stress (Rp0,2) or, for austenitic steels in the solution annealed condition, 1 % proof stress
31、(Rp1,0) 3.1.2 solution annealing softening heat treatment for austenitic steels in which a cylinder is heated to a uniform temperature above the solid solution temperature, followed by rapid cooling 3.1.3 cryoforming process where the cylinder is subjected to a controlled low temperature deformation
32、 treatment that results in a permanent increase in strength 3.1.4 cold working plastic deformation treatment given to sheet material at ambient temperature, with the aim of permanently increasing the material strength 3.1.5 cold forming final deformation treatment at ambient temperature given to the
33、 prefabricated cylinder, known as the preform, which results in a permanent increase in the material strength 3.1.6 batch quantity of cylinders made consecutively by the same manufacturer, using the same manufacturing techniques, to the same design, size and material, from the same cast on the same
34、type of welding machines and welding procedures BS ISO 18172-1:200733.1.7 design stress factor F ratio of equivalent wall stress at test pressure (ph) to guaranteed minimum yield stress (Re) 3.1.8 meta-stable austenitic steel CrNi stainless steel, which is austenitic in the annealed state at room te
35、mperature, but is unstable regarding transformation when plastically deformed at low temperatures 3.2 Symbols a calculated minimum thickness, in mm, of the cylindrical shell a guaranteed minimum thickness, in mm, of the cylindrical shell, including any corrosion allowance (see 7.1.1) a1calculated va
36、lue of a used in the calculation of b (see 5.3.2) ammean wall thickness, in mm, of the cylindrical shell of the cylinder preform A percentage elongation after fracture b calculated minimum thickness, in mm, of the cylinder end b guaranteed minimum thickness, in mm, of the cylinder end (see 7.1.1) C
37、shape factor of dished ends D outside diameter, in mm, of the cylinder (see Figure 1) Dfdiameter of former, in mm (see 8.4.3 and Figure 10) Dmmean diameter of the cylindrical shell of a cylinder preform, in mm F design stress factor (see 3.1.7) fccryoforming factor established by the manufacturer fo
38、r each batch of cylinders h height, in mm, of the cylindrical part of the end (see Figure 1) H outside height, in mm, of the domed part of the end (see Figure 1) J stress reduction factor L length, in mm, of the cylinder n ratio of diameter of bend test former (Df) to the thickness of the test piece
39、 (t) pbmeasured burst pressure, in MPa (bar)1), above atmospheric pressure, in the burst test pccryoforming or cold forming pressure in MPa (bar), above atmospheric pressure 1) 0,1 MPa = 105Pa = 1 bar BS ISO 18172-1:20074 phhydraulic test pressure, in MPa (bar), above atmospheric pressure pyobserved
40、 yield pressure, in MPa (bar), above atmospheric pressure r inside radius of the knuckle end, in mm (see Figure 1) R inside radius of the dished end, in mm (see Figure 1) Reyield stress, in MPa, as defined in 3.1.1 and used for design calculation Reavalue of the actual yield stress, in MPa, determin
41、ed by the tensile test Rp0,2minimum value of 0,2 % proof stress, in MPa, guaranteed by the cylinder manufacturer for the finished cylinder, in accordance with ISO 6892 (see Note) Rp1,0minimum value of 1,0 % proof stress, in MPa, guaranteed by the cylinder manufacturer for the finished cylinder, in a
42、ccordance with ISO 6892 (see Note) Rgminimum value of tensile strength, in MPa, guaranteed by the cylinder manufacturer for the finished cylinder Rmactual value of tensile strength, in MPa, determined by a tensile test (see 8.3) t actual thickness of the test specimen, in mm (see Figure 7) NOTE For
43、cryoformed and cold formed cylinders, the minimum value guaranteed by the manufacturer refers only to the cylindrical part of the finished cylinder. 4 Materials and heat treatment 4.1 General 4.1.1 Materials of shells and end pressings shall be stainless steels in a condition suitable for pressing o
44、r drawing and welding, and shall conform to ISO 9328-7. 4.1.2 Grades of steel used for the cylinder manufacture shall be compatible with the intended gas service (e.g. corrosive gases, embrittling gases), in accordance with ISO 11114-1. 4.1.3 There is a risk of sensitization to intergranular corrosi
45、on resulting from the hot processing of austenitic and duplex stainless steels. If any heat treatment was done during manufacturing, an intergranular corrosion test in accordance with 7.3.3 shall be carried out. 4.1.4 The manufacturer shall be able to guarantee cylinder steel casting traceability fo
46、r each pressure-retaining part of the cylinder. 4.1.5 All parts welded to the cylinder shall be made of compatible material with respect to the weldability. 4.1.6 The cylinder manufacturer shall obtain and provide material certificates of the ladle analysis from the steel manufacture of the steel su
47、pplied for the construction of the pressure-retaining parts of the cylinder and for the welding consumables. 4.1.7 Some grades of stainless steel may be susceptible to environmental stress corrosion cracking (SCC). A check shall be made of the material standard to ensure that the selection of materi
48、al is compatible with the intended service. Special precautions shall be taken, e.g. by carrying out a post-processing SCC test or by using a grade of material more resistant to SCC. No special precautions shall compromise any other requirements in this part of ISO 18172. BS ISO 18172-1:200754.1.8 T
49、he welding consumables shall be such that they are capable of giving consistent welds. The strength characteristics of the welds shall not be less than those considered in the design and/or calculations. 4.1.9 Cylinders for acetylene service shall be manufactured with materials compatible with the manufacturing process of the porous mass, or an internal coating shall be applied. 4.2 Categories The following three broad categories of stainless steels are recognised: ferrit
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1