BS ISO 19338-2014 Performance and assessment requirements for design standards on structural concrete《结构混凝土设计标准的功效和评定要求》.pdf

1、BSI Standards PublicationBS ISO 19338:2014Performance and assessmentrequirements for designstandards on structuralconcreteBS ISO 19338:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 19338:2014.The UK participation in its preparation was entrusted to Techn

2、icalCommittee B/525/2, Structural use of concrete.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Sta

3、ndards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 86125 3ICS 91.080.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2014

4、.Amendments issued since publicationDate Text affectedBS ISO 19338:2014 ISO 2014Performance and assessment requirements for design standards on structural concreteExigences de performance et dvaluation pour la conception des normes relatives au bton structurelINTERNATIONAL STANDARDISO19338Third edit

5、ion2014-09-15Reference numberISO 19338:2014(E)BS ISO 19338:2014ISO 19338:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electr

6、onic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41

7、 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 19338:2014ISO 19338:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 General requirements . 44.1 Overall

8、 structural concept . 44.2 Structural integrity 44.3 Design approach 44.4 Design service life . 44.5 Workmanship, materials and quality assurance 45 Performance requirements . 45.1 General . 45.2 Structural safety and ultimate limit states 45.3 Serviceability limit states . 45.4 Restorability limit

9、states . 55.5 Durability limit state 55.6 Fire resistance limit state. 55.7 Fatigue limit state . 56 Loadings and actions 56.1 General . 56.2 Load factors . 56.3 Action combinations 56.4 Permanent loads 66.5 Variable loads . 66.6 Accidental loads . 66.7 Construction loads . 66.8 Impact load . 66.9 E

10、arthquake forces. 66.10 Wind forces 66.11 Environmental actions . 67 Assessment . 67.1 Materials . 67.2 Analysis of concrete structures . 67.3 Strength calculations . 77.4 Partial safety factors for materials . 87.5 Resistance factors . 87.6 Resistance criteria 87.7 Stability 87.8 Precast concrete a

11、nd composite action . 87.9 Prestressed concrete 87.10 Designs for earthquake resistance . 97.11 Detailing requirements 97.12 Durability . 97.13 Fire . 98 Constructions and quality control 98.1 Construction requirements 98.2 Quality control 10BS ISO 19338:2014ISO 19338:2014(E)ForewordISO (the Interna

12、tional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has be

13、en established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stan

14、dardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accord

15、ance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details

16、 of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endo

17、rsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee respo

18、nsible for this document is ISO/TC 71, Concrete, reinforced concrete and pre-stressed concrete, Subcommittee SC 4, Performance requirements for structural concrete.This third edition cancels and replaces the second edition (ISO 19338:2007), of which it constitutes a minor revision. It also incorpora

19、tes the Technical Corrigenda ISO 19338:2007/Cor, 1:2008 and ISO 19338:2007/Cor, 2:2009.iv ISO 2014 All rights reservedBS ISO 19338:2014ISO 19338:2014(E)IntroductionConcrete is the most popular material used in the construction market. Presently, about one-third of a ton of concrete is produced each

20、year for every human being in the world (some 2 billion tons per year).International Standards on concrete technology can play a significant role for improving the global trade climate. International Standards in the field of concrete and its use in civil infrastructure are ever more needed as the e

21、conomic development of the world continues.ISO/TC 71/SC 4 was established to develop standards for performance requirements of structural concrete. This International Standard gives the performance and assessment requirements for design standards on concrete structures. It is an umbrella-type docume

22、nt with general provisions and guidelines intended to provide wide latitude of choice in terms of general requirements for performance and assessment of concrete structures. It should be used, therefore, in conjunction with sound engineering judgment.National and regional standards are generally mor

23、e prescriptive in nature than International Standards and vary somewhat from region to region.In a document accessible at http:/isotc.iso.org/livelink/livelink/Open/ISO_19338, ISO/TC 71/SC 4 has defined a procedure to assess whether a national or regional standard can be deemed to satisfy this Inter

24、national Standard. This separate document also gives the list of national and regional standards that so far have gone through the procedure and are deemed to satisfy this International Standard. ISO 2014 All rights reserved vBS ISO 19338:2014BS ISO 19338:2014Performance and assessment requirements

25、for design standards on structural concrete1 ScopeThis International Standard provides performance and assessment requirements for design standards of structural concrete. It can be used for international harmonization of design and construction requirements.This International Standard includesa) re

26、quirements, which define the required structural concrete performance,b) criteria, which give means for expressing the requirements, andc) assessment clauses, which give acceptable methods of verifying the specific criteria.2 Normative referencesThe following documents, in whole or in part, are norm

27、atively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2394, General principles on reliability for structuresISO

28、 6241, Performance standards in building Principles for their preparation and factors to be consideredISO 7162, Performance standards in building Contents and format of standards for evaluation of performance3 Terms and definitionsFor the purposes of this document, the following terms and definition

29、s apply.3.1accidental loadactions whose chance of occurrence is very small but intensity is very large compared with variable actions3.2actionassembly of concentrated or distributed mechanical forces acting on/in a structure (direct actions), deformations imposed on the structure or contained within

30、 it (indirect actions), or environmental actions (3.7)3.3analysis acceptable methods of evaluating the performance index or verifying the compliance of specific criteriaNote 1 to entry: Analysis may also be called assessment.3.4criteriameans of expressing the performance requirements for structural

31、concrete by specific technical values and appropriate limitsINTERNATIONAL STANDARD ISO 19338:2014(E) ISO 2014 All rights reserved 1BS ISO 19338:2014ISO 19338:2014(E)3.5design service lifeperiod for which the structure or structural element is to be used for its intended purpose with anticipated main

32、tenance but without substantial repair being necessary3.6durabilityability of a structure or structural element to assure no deterioration that is harmful to required performance in the relevant environment3.7environmental actionsassembly of physical, chemical, or biological influences which may cau

33、se restraint effects or deterioration to the materials making up the structure, which in turn may adversely affect its serviceability, restorability, and safety3.8experimental analysisuse of physical models to determine load-carrying capacity and serviceability of prototype design3.9limit statecriti

34、cal state specified using a performance index, beyond which the structure no longer satisfies the design performance requirement3.10limit states designdesign procedure where actions under factored loads are used to determine structural response and where resistance at limit state conditions is made

35、equal to or greater than the response3.11load factorsmultiplier(s) applied to load3.12maintenancetotal set of activities performed during the design service life of the structure to enable it to fulfil the performance requirements3.13modelssimplified mathematical descriptions of actions simulating e

36、xperimental setup, material properties, the behaviour of a structure, etc.3.14partial safety factors for materialsdevisors applied to the material characteristic strength in general conformance with reliability-based design requirementsNote 1 to entry: See also resistance factor (3.21).3.15performan

37、ce evaluationprocedure where actions at service load are used to determine structural response and limits are placed on response at service loads3.16performance requirementdefinition of the required structural performance in designed concrete structures2 ISO 2014 All rights reservedBS ISO 19338:2014

38、ISO 19338:2014(E)3.17permanent loadself-weights of structures including permanent attachments3.18reliabilityability of a structure or structural element to fulfil the specified requirements during design service life of the structure3.19representative value of actionvalue of action used for the veri

39、fication of criteria3.20resistanceability of a member to bear loads or section forcesNote 1 to entry: The resistance is also used to control response values, such as permissible crack width and deflection.3.21resistance factormultiplier applied to resistance in general conformance with reliability-b

40、ased design requirementsNote 1 to entry: When applied to materials, these multipliers may also be called material factors. See partial safety factors for materials (3.14).3.22robustnessability of a structure not to be damaged by events like fire, explosions, impact, or consequences of human errors,

41、to an extent disproportionate to the original cause3.23restorabilityability of a structure or structural element to be repaired physically and economically when damaged under the effects of considered actions3.24safetyability of a structure or structural element to assure no casualty to users of, an

42、d people around, the structure, within the limits of acceptable probability3.25serviceabilityability of a structure or structural elements to provide appropriate behaviour or functionality in use under the effects of considered actions at serviceability limit state3.26structural integrityability of

43、a structure to avoid widespread collapse when localized damage occurs3.27variable loadweights of moving objects on structures, as well as any other loads whose intensity is variable, including traffic loads, wave loads, wind loads, water pressures, earth pressures, and loads induced by temperature I

44、SO 2014 All rights reserved 3BS ISO 19338:2014ISO 19338:2014(E)4 General requirements4.1 Overall structural conceptThe overall quality of a structure shall be implemented through strict quality control and care by a knowledgeable qualified design professional complying with ISO 2394, ISO 6241, and I

45、SO 7162. In conceiving a structural system, load-carrying behaviour under maximum and frequent loads, materials and their combinations, constructibility, costs, and environmental aspects and aesthetics shall be considered. 4.2 Structural integrityDesign of concrete structures shall provide general s

46、tructural integrity, directly or implicitly. Localized damage or deterioration in a structure shall not impair general structural integrity.4.3 Design approachA design standard for structural concrete shall be based on quantitative performance evaluation at the limit states. Design shall consider sa

47、fety, serviceability, restorability, structural integrity, robustness, environmental adequacy, and durability. Where applicable, limit states caused by fatigue, fire, explosion, impact, and rare accidental actions or other extreme loadings or actions shall be considered.4.4 Design service lifeDesign

48、 service life shall be defined in consideration of the structural role, the social importance of the structures concerned, and the economically justified service life. Structural requirements shall be satisfied throughout the defined design life.4.5 Workmanship, materials and quality assuranceIn ord

49、er for the properties of the completed structure to be consistent with the requirements and the assumptions made during the planning and design, quality assurance and execution expectations for construction shall be considered and adequate quality control measures shall be taken.5 Performance requirements5.1 GeneralFor limit states, the design standard shall specify sets of action combinations and a reliability-based design concept that can be analytically demonstrated to give an adequate performance level during the design life of the structure.5.2 Stru