BS ISO 199-2014 Rolling bearings Thrust bearings Geometrical product specification (GPS) and tolerance values《滚动轴承 止推轴承 几何产品规格 (GPS) 和公差值》.pdf

1、BSI Standards PublicationBS ISO 199:2014Rolling bearings Thrustbearings Geometricalproduct specification (GPS) andtolerance valuesBS ISO 199:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 199:2014. Itsupersedes BS ISO 199:2005 which is withdrawn.The UK pa

2、rticipation in its preparation was entrusted to TechnicalCommittee MCE/7, Rolling bearings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible fo

3、r its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 79153 6ICS 21.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy an

4、d Strategy Committee on 31 July 2014.Amendments issued since publicationDate Text affectedBS ISO 199:2014 ISO 2014Rolling bearings Thrust bearings Geometrical product specification (GPS) and tolerance valuesRoulements Butes Spcification gomtrique des produits (GPS) et valeurs de tolranceINTERNATIONA

5、L STANDARDISO199Fourth edition2014-07-15Reference numberISO 199:2014(E)BS ISO 199:2014ISO 199:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or

6、 by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-12

7、11 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 199:2014ISO 199:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 15 Limit d

8、eviations and tolerance values . 75.1 General . 75.2 Tolerance class Normal 85.3 Tolerance class 6 . 105.4 Tolerance class 5 . 125.5 Tolerance class 4 . 14Annex A (informative) Symbols and terms as given in ISO 199:2005 in relationship to new descriptions given in this document .16Annex B (informati

9、ve) Example of drawing indications of characteristics with specification for thrust bearings 18Annex C (informative) Illustration of ISO 1132-14and ISO 14405-1 terms and definitions .20Annex D (informative) Description with illustrations for specification modifiers of linear sizes 25Bibliography .33

10、BS ISO 199:2014ISO 199:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interest

11、ed in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Co

12、mmission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents

13、 should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible fo

14、r identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the c

15、onvenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Forew

16、ord - Supplementary informationThe committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 4, Tolerances, tolerance definitions and symbols (including GPS).This fourth edition cancels and replaces the third edition (ISO 199:2005), which has been technically revised.iv

17、ISO 2014 All rights reservedBS ISO 199:2014ISO 199:2014(E)IntroductionThis International Standard is a machine element geometry standard as defined in the geometrical product specification (GPS) system as presented in master plan of ISO/TR 14638.10The fundamental rules of ISO/GPS given in ISO 80157a

18、pply to this International Standard and the default decision rules given in ISO 14253-18apply to the specifications made in accordance with this International Standard, unless otherwise indicated.The connection between functional requirements, measuring technique and measuring uncertainty is always

19、intended to be considered. The traditionally used measuring technique is described in ISO 1132-2.5For measurement uncertainty it is intended that ISO 14253-29should be considered. ISO 2014 All rights reserved vBS ISO 199:2014BS ISO 199:2014Rolling bearings Thrust bearings Geometrical product specifi

20、cation (GPS) and tolerance values1 ScopeThis International Standard specifies dimensional characteristics, limit deviations from nominal values, and tolerance values to define the interface (except chamfers) of thrust rolling bearings. Nominal boundary dimensions are defined in ISO 1041.This Interna

21、tional Standard is not applicable to certain thrust bearings (e.g. thrust needle roller bearings) or for particular fields of application (e.g. special thrust precision bearings). Tolerances for such bearings are given in the relevant International Standards.Chamfer dimension limits are given in ISO

22、 5823.2 Normative referencesThe following documents in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

23、mendments) applies.ISO 5593, Rolling bearings VocabularyISO 14405-1, Geometrical product specifications (GPS) Dimensional tolerancing Part 1: Linear sizesISO/TS 17863, Geometrical product specification (GPS) Geometrical tolerancing of moveable assemblies3 Terms and definitionsFor the purposes of thi

24、s document, the terms and definitions in ISO 5593, ISO 14405-1, and ISO/TS 17863 apply.4 SymbolsTo express that the ISO/GPS system, ISO 8015 7is applied, the dimensional characteristics shall be included in the technical product documentation (for example on the drawing). The dimensional specificati

25、ons, associated to these characteristics, are described in Table 1 and Figures 1 to 4.Descriptions for symbols are in accordance with GPS terminology; relationships with traditional terms are described in Annex A.A tolerance value associated to a characteristic is symbolized by t followed by the sym

26、bol for characteristic, for example, tdmp.In this International Standard, the ISO default specification operator for size is in accordance with ISO 14405-1, i.e. the two-point size is valid. Some specification modifiers are described in Annex D.The detailed definitions for terms in ISO 14405-1 and t

27、raditional terms in ISO 1132-14are not fully equal, for differences, see Annex C.INTERNATIONAL STANDARD ISO 199:2014(E) ISO 2014 All rights reserved 1BS ISO 199:2014ISO 199:2014(E)Table 1 Symbols for nominal sizes, characteristics and specification modifiersSymbol for nominal size aSymbol for charac

28、teristic aGPS symbol and specification modifier b cDescription dSee Figured Nominal bore diameter of shaft washer, single-direction bearing1; 2dmpACSDeviation of a mid-range size (out of two-point sizes) of shaft washer bore diameter in any cross-section from its nominal size1; 2VdspACSRange of two-

29、point sizes of shaft washer bore diameter in any cross-section1; 2d2Nominal bore diameter of central shaft washer, double-direction bearing3; 4d2mpACSDeviation of a mid-range size (out of two-point sizes) of central shaft washer bore diameter in any cross-section from its nominal size3; 4Vd2spACSRan

30、ge of two-point sizes of central shaft washer bore diameter in any cross-section3; 4D Nominal outside diameter of housing washer1; 2; 3; 4DmpACSDeviation of a mid-range size (out of two-point sizes) of housing washer outside diameter in any cross-section from its nominal size1; 2; 3; 4VDspACSRange o

31、f two-point sizes of housing washer outside diameter in any cross-section1; 2; 3; 4T Nominal assembled bearing height, single-direction bearing1; 2TsGNeDeviation of minimum circum-scribed size of assembled bear-ing height from its nominal size, single-direction bearing1; 22 ISO 2014 All rights reser

32、vedBS ISO 199:2014ISO 199:2014(E)Table 1 (continued)Symbol for nomi-nal sizeaSymbol for characteristicaGPS symbols and specification modifiersb cDescriptionsdSee Fig-ureT1Nominal assembled bearing height, double-direction bearing3; 4T1sGNeDeviation of minimum circum-scribed size of assembled bearing

33、 height from its nominal size, double-direction bearing3; 4Se fThrust cylindrical roller bear-ings: range of two-point sizes of thickness between housing washer raceway and the back face2; 4ALSSNLSThrust ball bearings: range of minimum spherical sizes between the raceway and the opposite back face o

34、f the housing washer, obtained from any longitudinal section which includes the housing washer outside surface axis1; 3Si fThrust cylindrical roller bear-ings: range of two-point sizes of thickness between shaft washer raceway and the back face2ALSSNLSThrust ball bearings: range of minimum spherical

35、 sizes between the raceway and the opposite back face of the shaft washer, obtained from any longitudinal section which includes the shaft washer bore axis1aSymbols as defined in ISO 1524112except for the format used.bSymbols as defined in ISO 14405-1.cSpecification modifier shall not be indicated o

36、n a drawing, because two-point size is the default specification modifier for size.dDescriptions based on ISO 14405-1.esymbols for direction of gravity Gaccording to ISO/TS 17863, see Figures 1 to 4.fApplies only to thrust ball bearings with 90 contact angle and thrust cylindrical roller bearings wi

37、th 90 contact angle.The indications in Figures 1 to 4 illustrate the correlation of interface dimensions and corresponding dimensional tolerance symbols.NOTE Figures 1 to 4 are drawn schematically and do not necessarily show all design details.Two examples of a real drawing indication are given in A

38、nnex B. ISO 2014 All rights reserved 3BS ISO 199:2014ISO 199:2014(E)ACStVdsptVDspACStdmpACSd T tTsGN 1 2tDmpACSDKMGG2GG1tSet SiSN K LS ALSSN M LS ALS121 =G1 or G2=2the rolling elements shall be in contact with both shaft and housing washer racewaysKey1 housing washer2 shaft washerFigure 1 Size speci

39、fication for single-direction bearing Thrust ball bearingACSt SitVDspACSACStVdsptSetdmpd ACStDmpDT tTsGN 1 2GG2GG1121 =G1 or G2=2the rolling elements shall be in contact with both shaft and housing washer racewaysKey1 housing washer2 shaft washerFigure 2 Size specification for single-direction beari

40、ng Thrust cylindrical roller bearing4 ISO 2014 All rights reservedBS ISO 199:2014ISO 199:2014(E)112MtVDspACStVDspACST tT1sGN121tDmpACSDtDmp ACSDGG2GG1Lt ACSd 2 d2mptVd2spACS tSeSN L LS ALStSeSN M LS ALS1 =G1 or G2=2the rolling elements shall be in contact with both shaft and housing washer racewaysK

41、ey1 housing washer2 central shaft washerFigure 3 Size specification for double-direction bearing Thrust ball bearing ISO 2014 All rights reserved 5BS ISO 199:2014ISO 199:2014(E)1121 =G1 or G2=2the rolling elements shall be in contact with both shaft and housing washer racewaysKey1 housing washer2 ce

42、ntral shaft washerFigure 4 Size specification for double-direction bearing Thrust cylindrical roller bearing6 ISO 2014 All rights reservedBS ISO 199:2014ISO 199:2014(E)5 Limit deviations and tolerance values5.1 GeneralLimit deviations and tolerance values for single-direction and double-direction th

43、rust bearings are given in Tables 2 to 9.NOTE Details, except for inner diameter, of the central washer will be dealt with in a future revision of this International Standard.In Tables 2 to 9, the symbols U and L are used as follows:U = upper limit deviation;L = lower limit deviation. ISO 2014 All r

44、ights reserved 7BS ISO 199:2014ISO 199:2014(E)5.2 Tolerance class NormalSee Tables 2 and 3.Table 2 Shaft washer, central shaft washer, and bearing height Tolerance class NormalLimit deviations and tolerance values in micrometersd, d2mmtdmp, td2mptVdsp, tVd2sptSia btTstT1s U L U L U L 18 0 8 6 10 +20

45、 250 +150 40018 30 0 10 8 10 +20 250 +150 40030 50 0 12 9 10 +20 250 +150 40050 80 0 15 11 10 +20 300 +150 50080 120 0 20 15 15 +25 300 +200 500120 180 0 25 19 15 +25 400 +200 600180 250 0 30 23 20 +30 400 +250 600250 315 0 35 26 25 +40 400 315 400 0 40 30 30 +40 500 400 500 0 45 34 30 +50 500 500 6

46、30 0 50 38 35 +60 600 630 800 0 75 55 40 +70 750 800 1 000 0 100 75 45 +80 1 000 1 000 1 250 0 125 95 50 +100 1 400 1 250 1 600 0 160 120 60 +120 1 600 1 600 2 000 0 200 150 75 +140 1 900 2 000 2 500 0 250 190 90 +160 2 300 NOTE For double-direction bearings, the values apply only up to and includin

47、g d2= 190 mm.aApplies only to thrust ball bearings with 90 contact angle and thrust cylindrical roller bearings with 90 contact angle.bIs not applicable for central shaft washer.8 ISO 2014 All rights reservedBS ISO 199:2014ISO 199:2014(E)Table 3 Housing washer Tolerance class NormalLimit deviations

48、and tolerance values in micrometersD mmtDmptVDsptSea U L10 18 0 11 8Identical to tSiof shaft washer of same bearing18 30 0 13 1030 50 0 16 1250 80 0 19 1480 120 0 22 17120 180 0 25 19180 250 0 30 23250 315 0 35 26315 400 0 40 30400 500 0 45 34500 630 0 50 38630 800 0 75 55800 1 000 0 100 751 000 1 2

49、50 0 125 951 250 1 600 0 160 1201 600 2 000 0 200 1502 000 2 500 0 250 1902 500 2 850 0 300 225NOTE For double-direction bearings, the values apply only up to and including D = 360 mm.aApplies only to thrust ball bearings with 90 contact angle and thrust cylindrical roller bearings with 90 contact angle. ISO 2014 All rights reserved 9BS ISO 199:201