BS ISO 20515-2012 Rolling bearings Radial bearings retaining slots Dimensions and tolerances《滚动轴承 保留开槽的径向轴承 尺寸规格和公差》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 20515:2012Rolling bearings Radialbearings, retaining slots Dimensions and tolerancesBS ISO 20515:2012 BRITISH STANDARDNational forewordThis British Standard is the UK impl

2、ementation of ISO 20515:2012. Itsupersedes BS ISO 20515:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/7, Rolling bearings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does n

3、ot purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 76134 8ICS 21.100.20Compliance with a British Standard cannot confer immunity fromlegal obli

4、gations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2012.Amendments issued since publicationDate Text affectedBS ISO 20515:2012 ISO 2012Rolling bearings Radial bearings, retaining slots Dimensions and tolerancesRoulements Roulement

5、s radiaux, encoches de retenue Dimensions et tolrancesINTERNATIONAL STANDARDISO20515Second edition2012-06-01Reference numberISO 20515:2012(E)BS ISO 20515:2012ISO 20515:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part

6、of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH

7、-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 20515:2012ISO 20515:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Terms and definitions . 14 Symbols . 15 Dimensions .

8、 35.1 General . 35.2 Single-row angular contact ball bearings and four-point-contact ball bearings . 35.3 Radial cylindrical roller bearings 66 Tolerances . 7BS ISO 20515:2012ISO 20515:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national stand

9、ards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International orga

10、nizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given i

11、n the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 %

12、of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 20515 was prepared by Technical Committee ISO/TC 4, Rolling be

13、arings, Subcommittee SC 12, Ball bearings.This second edition cancels and replaces the first edition (ISO 20515:2007), of which it constitutes a minor revision. In particular, a new Figure 2 and a corrected title for Table 6 have been added.iv ISO 2012 All rights reservedBS ISO 20515:2012INTERNATION

14、AL STANDARD ISO 20515:2012(E)Rolling bearings Radial bearings, retaining slots Dimensions and tolerances1 ScopeThis International Standard specifies dimensions and tolerances of retaining slots to be used for outer rings of single-row angular contact ball bearings, four-point-contact ball bearings a

15、nd radial cylindrical roller bearings. The retaining slots are not suitable for use in the outer rings of sealed and shielded radial ball bearings, nor in the outer rings of radial cylindrical roller bearings without ribs.2 Normative referencesThe following referenced documents are indispensable for

16、 the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 15, Rolling bearings Radial bearings Boundary dimensions, general planISO 1132-1, Rolling bearings Tol

17、erances Part 1: Terms and definitionsISO 5593, Rolling bearings VocabularyISO 15241, Rolling bearings Symbols for quantities 3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 1132-1 and ISO 5593 and the following apply.3.1retaining slotangled slot in an

18、 outer ring at the intersection of the outside surface and the face of the ringNOTE The slot is to provide a simple means of preventing rotation of the outer ring of a bearing.4 SymbolsFor the purposes of this document, the symbols given in ISO 15241 and the following apply.The symbols (except those

19、 for tolerances) shown in Figure 1, and the values given in Tables 1 to 6, denote nominal dimensions, unless specified otherwise.NOTE Figures 1 and 2 show four-point-contact ball bearings with one retaining slot and two retaining slots, respectively. b retaining slot widthD outside diameter of outer

20、 ringh retaining slot depthr0fillet radius at bottom of retaining slott retaining slot symmetry or position tolerance ISO 2012 All rights reserved 1BS ISO 20515:2012ISO 20515:2012(E)bsdeviation of a single retaining slot widthhsdeviation of a single retaining slot depthFigure 1 Retaining slot in rad

21、ial bearing with one retaining slot2 ISO 2012 All rights reservedBS ISO 20515:2012ISO 20515:2012(E)Figure 2 Retaining slot in radial bearing with two diametrically opposed retaining slots5 Dimensions5.1 GeneralThe dimensions for retaining slots in single-row angular contact ball bearings and four-po

22、int-contact ball bearings of diameter series 0, 2, 3 and 4, and radial cylindrical roller bearings of dimension series 10, 02E, 22E, 03E, 23E and 04, are given in Tables 1 and 2, respectively.The diameter series and dimension series referred to in Tables 1 and 2 are those defined in ISO 15.NOTE For

23、radial cylindrical roller bearings of dimension series 02E, 22E, 03E and 23E, the E signifies that they are of a design having reinforced roller and cage assembly and increased radial load-carrying capacity.5.2 Single-row angular contact ball bearings and four-point-contact ball bearingsTable 1 Diam

24、eter series 0, 2, 3 and 4Dimensions in millimetresDDiameter series0 2 3 4h b r0h b r0h b r0h b r0max. max. max. max.40 2,5 3,5 0,5 47 2,5 3,5 0,5 3 4,5 0,5 3,5 4,5 0,5 50 3 4,5 0,5 52 3 3,5 0,5 3 4,5 0,5 3,5 4,5 0,5 3,5 4,5 0,555 3 3,5 0,5 56 3,5 4,5 0,5 58 3 3,5 0,5 3 4,5 0,5 62a3,5a4,5a0,5a3,5 4,5

25、 0,5 3,5 4,5 0,5 3,5 4,5 0,565 3,5 4,5 0,5 ISO 2012 All rights reserved 3BS ISO 20515:2012ISO 20515:2012(E)DDiameter series0 2 3 4h b r0h b r0h b r0h b r0max. max. max. max.68 3,5 4,5 0,5 3,5 4,5 0,5 72 3,5 4,5 0,5 3,5 4,5 0,5 3,5 4,5 0,575a4a5,5a0,5a 4 5,5 0,5 80a4a5,5a0,5a4 5,5 0,5 4 5,5 0,5 4 5,5

26、 0,585 4 5,5 0,5 90 4 5,5 0,5 4 5,5 0,5 4 5,5 0,5 4 5,5 0,595 4 5,5 0,5 100a5a6,5a0,5a5 6,5 0,5 5 6,5 0,5 5 6,5 0,5110 5 6,5 0,5 5 6,5 0,5 5 6,5 0,5 5 6,5 0,5115 5 6,5 0,5 120 6,5 6,5 0,5 8,1 6,5 1 8,1 6,5 1125 5 6,5 0,5 6,5 6,5 0,5 130 5 6,5 0,5 6,5 6,5 0,5 8,1 6,5 1 8,1 6,5 1140a5 6,5 0,5 8,1a6,5a

27、1a8,1 6,5 1 8,1 6,5 1145 5 6,5 0,5 150 6,5 6,5 0,5 8,1 6,5 1 10,1 8,5 2 10,1 8,5 2160 6,5 6,5 0,5 8,1 6,5 1 10,1 8,5 2 10,1 8,5 2170 6,5 6,5 0,5 8,1 6,5 1 10,1 8,5 2 180 6,5 6,5 0,5 10,1 8,5 2 11,7 10,5 2 11,7 10,5 2190 10,1 8,5 2 11,7 10,5 2 11,7 10,5 2200 8,1 6,5 1 10,1 8,5 2 11,7 10,5 2 11,7 10,5

28、 2210 8,1 6,5 1 11,7 10,5 2215 11,7 10,5 2 11,7 10,5 2 225 8,1 6,5 1 11,7 10,5 2 11,7 10,5 2230 11,7 10,5 2 240 10,1 8,5 2 11,7 10,5 2 11,7 10,5 2250 11,7 10,5 2 11,7 10,5 2260 11,7 10,5 2 11,7 10,5 2 11,7 10,5 2270 11,7 10,5 2 280 11,7 10,5 2 12,7 10,5 2 12,7 10,5 2290 11,7 10,5 2 12,7 10,5 2 300 1

29、2,7 10,5 2 310 12,7 10,5 2 12,7 10,5 2 12,7 10,5 2320 12,7 10,5 2 12,7 10,5 2 Table 1 (continued)4 ISO 2012 All rights reservedBS ISO 20515:2012ISO 20515:2012(E)DDiameter series0 2 3 4h b r0h b r0h b r0h b r0max. max. max. max.340 12,7 10,5 2 12,7 10,5 2 12,7 10,5 2 12,7 10,5 2360 12,7 10,5 2 12,7 1

30、0,5 2 12,7 10,5 2 12,7 10,5 2380 12,7 10,5 2 12,7 10,5 2400 12,7 10,5 2 12,7 10,5 2 12,7 10,5 2 12,7 10,5 2420 15 12,5 2,5 15 12,5 2,5 15 12,5 2,5440 15 12,5 2,5 15 12,5 2,5460 15 12,5 2,5 15 12,5 2,5 15 12,5 2,5480 15 12,5 2,5 15 12,5 2,5 15 12,5 2,5500 15 12,5 2,5 15 12,5 2,5 aThese values are not

31、 suitable for single-row angular contact ball bearings or four-point-contact ball bearings with a contact angle of less than 35.Table 1 (continued) ISO 2012 All rights reserved 5BS ISO 20515:2012ISO 20515:2012(E)5.3 Radial cylindrical roller bearingsTable 2 Dimension series 10, 02E, 22E, 03E, 23E an

32、d 04Dimensions in millimetresDDimension series10 02E, 22E 03E, 23E 04h b r0h b r0h b r0h b r0max. max. max. max.47 2,5 3,5 0,5 52 2,5 3,5 0,5 2,5 3,5 0,5 62 2,5 3,5 0,5 3 4,5 0,5 3 4,5 0,5 68 2,5 3,5 0,5 72 3,5 4,5 0,5 4 5,5 0,5 5 6,5 0,575 3 4,5 0,5 80 3 4,5 0,5 4 5,5 0,5 4 5,5 0,5 5 6,5 0,585 4 5,

33、5 0,5 90 4 5,5 0,5 4 5,5 0,5 5 6,5 0,5 5 6,5 0,595 4 5,5 0,5 100 4 5,5 0,5 4 5,5 0,5 5 6,5 0,5 6,5 6,5 0,5110 4 5,5 0,5 5 6,5 0,5 6,5 6,5 0,5 6,5 6,5 0,5115 4 5,5 0,5 120 5 6,5 0,5 6,5 6,5 0,5 6,5 6,5 0,5125 5 6,5 0,5 5 6,5 0,5 130 5 6,5 0,5 5 6,5 0,5 8,1 6,5 1 6,5 6,5 0,5140 6,5 6,5 0,5 6,5 6,5 0,5

34、 8,1 6,5 1 8,1 6,5 1145 6,5 6,5 0,5 150 6,5 6,5 0,5 6,5 6,5 0,5 8,1 6,5 1 8,1 6,5 1160 6,5 6,5 0,5 6,5 6,5 0,5 8,1 6,5 1 8,1 6,5 1170 6,5 6,5 0,5 8,1 6,5 1 8,1 6,5 1 180 6,5 6,5 0,5 8,1 6,5 1 10,1 8,5 2 10,1 8,5 2190 8,1 6,5 1 10,1 8,5 2 10,1 8,5 2200 8,1 6,5 1 8,1 6,5 1 11,7 10,5 2 11,7 10,5 2210 8

35、,1 6,5 1 12,7 10,5 2215 10,1 8,5 2 11,7 10,5 2 225 10,1 8,5 2 11,7 10,5 2 12,7 10,5 2230 10,1 8,5 2 240 10,1 8,5 2 11,7 10,5 2 12,7 10,5 2250 11,7 10,5 2 12,7 10,5 2260 11,7 10,5 2 11,7 10,5 2 12,7 10,5 2270 11,7 10,5 2 6 ISO 2012 All rights reservedBS ISO 20515:2012ISO 20515:2012(E)DDimension serie

36、s10 02E, 22E 03E, 23E 04h b r0h b r0h b r0h b r0max. max. max. max.280 11,7 10,5 2 12,7 10,5 2 15 12,5 2,5290 11,7 10,5 2 12,7 10,5 2 300 15 12,5 2,5 310 12,7 10,5 2 12,7 10,5 2 15 12,5 2,5320 12,7 10,5 2 15 12,5 2,5 340 12,7 10,5 2 12,7 10,5 2 15 12,5 2,5 15 12,5 2,5360 12,7 10,5 2 12,7 10,5 2 15 1

37、2,5 2,5380 20 15,5 3400 20 15,5 3420 20 15,5 3440 20 15,5 3460 20 15,5 3480 20 15,5 36 TolerancesThe tolerances for retaining slots in single-row angular contact ball bearings and four-point-contact ball bearings of diameter series 0, 2, 3 and 4, and radial cylindrical roller bearings of dimension s

38、eries 10, 02E, 22E, 03E, 23E and 04, are given in Tables 3 to 6.The diameter series and dimension series referred to in Tables 3 and 4 are those defined in ISO 15.Table 2 (continued) ISO 2012 All rights reserved 7BS ISO 20515:2012ISO 20515:2012(E)Table 3 Retaining slot depth for single-row angular c

39、ontact ball bearings and four-point-contact ball bearingsDimensions and tolerance values in millimetreshDiameter series0 2, 3 and 4hshshigh low high low2,5+0,5 0 +1 033,5456,58,110,111,712,7+1,4 0 +1,4 015Table 4 Retaining slot depth for radial cylindrical roller bearingsDimensions and tolerance val

40、ues in millimetreshDimension series10 02E, 22E, 03E, 23E and 04hshshigh low high low2,5+0,5 0 +1 033,5456,58,110,111,712,7+1,4 0 +1,4 01520 +2 0 +2 08 ISO 2012 All rights reservedBS ISO 20515:2012ISO 20515:2012(E)Table 5 Retaining slot widthDimensions and tolerance values in millimetresbbshigh low3,

41、5+0,2 04,55,56,5+0,4 08,510,512,5+0,6 015,5Table 6 Retaining slot symmetry and position toleranceDimensions and tolerance values in millimetresD t max. 290 0,2290 0,4 ISO 2012 All rights reserved 9BS ISO 20515:2012ISO 20515:2012(E) ISO 2012 All rights reservedICS 21.100.20Price based on 8 pagesThis

42、page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. Britis

43、h Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revisio

44、n. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform

45、the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS whi

46、ch ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996