1、BS ISO22915-21:2009ICS 53.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDIndustrial trucks Verification of stabilityPart 21: Order-picking trucks withoperator position elevating above 1 200mmThis British Standardwas published underthe authority of theStandar
2、ds Policy andStrategy Committee on 30November 2009. BSI 2009ISBN 978 0 580 62103 1Amendments/corrigenda issued since publicationDate CommentsBS ISO 22915-21:2009National forewordThis British Standard is the UK implementation of ISO 22915-21:2009.The UK participation in its preparation was entrusted
3、to TechnicalCommittee MHE/7, Industrial trucks.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a
4、British Standard cannot confer immunityfrom legal obligations.BS ISO 22915-21:2009Reference numberISO 22915-21:2009(E)ISO 2009INTERNATIONAL STANDARD ISO22915-21First edition2009-08-01Industrial trucks Verification of stability Part 21: Order-picking trucks with operator position elevating above 1 20
5、0 mm Chariots de manutention Vrification de la stabilit Partie 21: Chariots prparateurs de commandes avec un poste de loprateur levable au-dessus de 1 200 mm BS ISO 22915-21:2009ISO 22915-21:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing poli
6、cy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central
7、Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken t
8、o ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publ
9、ication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Gene
10、va 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 22915-21:2009ISO 22915-21:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide
11、 federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that
12、committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in acc
13、ordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ
14、ires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 22915-21 was prepared by Tech
15、nical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2, Safety of powered industrial trucks. ISO 22915 consists of the following parts, under the general title Industrial trucks Verification of stability: Part 1: General Part 2: Counterbalanced trucks with mast Part 3: Reach and straddle t
16、rucks Part 4: Pallet stackers, double stackers and order-picking trucks with operator position elevating up to and including 1 200 mm lift height Part 5: Single side loading trucks Part 7: Bidirectional and multidirectional trucks Part 8: Additional stability test for trucks operating in the special
17、 condition of stacking with mast tilted forward and load elevated Part 10: Additional stability test for trucks operating in the special condition of stacking with load laterally displaced by powered devices Part 20: Additional stability test for trucks operating in the special condition of offset l
18、oad, offset by utilization Part 21: Order-picking trucks with operator position elevating above 1 200 mm The following parts are under preparation: Part 9: Counterbalanced trucks with mast handling freight containers of 6 m (20 ft) length and longer Part 11: Industrial variable reach trucks BS ISO 2
19、2915-21:2009ISO 22915-21:2009(E) iv ISO 2009 All rights reserved Part 12: Industrial variable reach trucks handling freight containers of 6 m (20 ft) length and longer Part 14: Rough-terrain variable reach trucks Part 15: Counterbalanced trucks with articulated steering Part 16: Pedestrian-propelled
20、 trucks Part 17: Burden and personnel carriers BS ISO 22915-21:2009INTERNATIONAL STANDARD ISO 22915-21:2009(E) ISO 2009 All rights reserved 1Industrial trucks Verification of stability Part 21: Order-picking trucks with operator position elevating above 1 200 mm 1 Scope This part of ISO 22915 specif
21、ies the tests for verifying the stability of order-picking trucks with an elevating operator position, as defined in ISO 5053, where the operators position can be raised to an elevation above 1 200 mm. It is applicable to industrial trucks fitted with fork arms, platforms and/or integrated attachmen
22、ts under normal operating conditions. It is not applicable to trucks fitted with a load carrier that can be shifted laterally or pivoted out of the trucks longitudinal centre plane. 2 Normative references The following referenced documents are indispensable for the application of this document. For
23、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5053, Powered industrial trucks Terminology ISO 22915-1, Industrial trucks Verification of stability General 3 Terms and definitions For the
24、 purposes of this document, the terms and definitions given in ISO 5053 and ISO 22915-1, and the following apply. 3.1 normal operating conditions operating conditions corresponding to the truck travelling indoors on smooth, level floors of sufficient strength such as those of concrete NOTE This defi
25、nition is different from the one given for normal operating conditions in ISO 22915-1:2008. 3.2 guided steering steering mode, either mechanical (e.g. guidance rails) or non-mechanical (e.g. inductive guidance, laser sensor or infrared) not controlled directly by the operator, used to steer the truc
26、k on a predetermined straight path while travelling BS ISO 22915-21:2009ISO 22915-21:2009(E) 2 ISO 2009 All rights reserved3.3 restricted steering operation under which the trucks steering is controlled by the operator and the steering angle is limited to not more than 10 from the forward or reverse
27、 travel direction 3.4 unrestricted steering steering mode controlled by the operator with no limitation of the steering angle 4 Test conditions 4.1 General See ISO 22915-1. 4.2 Position of truck on tilt table 4.2.1 Load and drive/steer axles The load axle and the drive/steer axle are defined by Figu
28、re 1. Key AA longitudinal centre plane of truck BB drive/steer axle CC load axle Figure 1 Load and drive/steer axles 4.2.2 Test 1 The truck shall be positioned on the tilt table so that its drive/steer axle, BB, and load axle, CC, are parallel to the tilt axis, XY, of the tilt table. See Table 1. 4.
29、2.3 Tests 2, 3, 4 and 5 The truck shall be positioned on the tilt table with the line, MN, parallel to the tilt axis, XY, of the tilt table. See Table 1. Point M is defined as follows. a) For trucks with a single drive (steer) wheel: point M shall be the vertical projection onto the tilt table of th
30、e point of intersection between the centreline of the drive/steer axle and the centreline of the drive wheel width. b) For trucks with a drive/steer axle in an articulating frame articulated in the centre plane of the truck: point M shall be the vertical projection onto the tilt table of the point o
31、f intersection between the lateral axis of the articulating frame and the centre plane, AA, of the truck. BS ISO 22915-21:2009ISO 22915-21:2009(E) ISO 2009 All rights reserved 3c) For trucks with dual drive (steer) wheels: point M shall be the vertical projection onto the tilt table of the point of
32、intersection between the centreline of the drive/steer axle and the centre plane, AA, of the truck. d) For trucks with non-articulated, non-sprung castors: point M shall be the vertical projection onto the tilt table of the point of intersection between the centreline of the castor wheel width, with
33、 the non-sprung castor positioned with the centreline of the castor wheel axle nearer to the centre plane of the truck. e) For trucks with non-articulated, non-sprung castors or wheels and a non-articulated drive wheel: 1) for the non-sprung castor or wheel, point M shall be the vertical projection
34、onto the tilt table of the point of intersection between the centreline of the castor or wheel axle and the centreline of the castor wheel or drive wheel width, with the non-sprung castor or wheel being positioned with the centreline of the castor wheel axle nearer to the centre plane of the truck;
35、2) for the non-articulated drive wheel, point M shall be the vertical projection onto the tilt table of the point of intersection between the centreline of the drive wheel axle and the centre line of the drive wheel width. f) For trucks with a sprung castor or wheel point: point M shall be the verti
36、cal projection onto the tilt table of the point of intersection between the centre line of the drive wheel axle and the centre line of the drive wheel width. As shown in Table 1, point N is defined as the centre point of the area of contact between the tilt table surface and the front load wheel clo
37、sest to the tilt axis, XY, of the tilt table. 4.3 Lift height Lift heights for tests shall be measured from the tilt table to the upper-most point of the load-carrying surface. 5 Verification of stability The stability shall be verified in accordance with Table 1. BS ISO 22915-21:2009ISO 22915-21:20
38、09(E) 4 ISO 2009 All rights reservedTable 1 Verification of stabilityTest criteria Test 1 Test 2 Test 3 Test 4 Test 5 Guided xxRestricted xxSteering Unrestrictedx x x x LongitudinalxDirection of test Lateralx x x x Withx x x x Load Withoutx x x x Lift heightb b c c d(4 +1,24v) % eTilt-tableangle (8
39、+1,24v) % f6 % (6 +1,24v) % (6 +2,48v) % (15 +1,1v) % vis the maximum travel speedofthe unladen truck, in km/h. BS ISO 22915-21:2009ISO 22915-21:2009(E) ISO 2009 All rights reserved 5Table1(continued) Test criteria Test 1 Asper4.2.2Truck position on tilt table Load leading Truck position on tilt tab
40、le Load trailing BS ISO 22915-21:2009ISO 22915-21:2009(E) 6 ISO 2009 All rights reservedTable1(continued) Tests 2 to 5Test criteria Tests 2, 3 and 5 Tests 2, 4 and 5 Tests 2 to 5 (pointsM and N)Asper4.2.3 a) Asper4.2.3 b) Asper4.2.3 c) Truck position on tilt table Key1 articulated rear wheelmounting
41、BS ISO 22915-21:2009ISO 22915-21:2009(E) ISO 2009 All rights reserved 7Table1(continued) Test criteria Tests 2 to 5 (pointsM and N)Asper4.2.3 d) Asper4.2.3 e)1) Asper4.2.3 e)2) Asper4.2.3 f) Truck position on tilt table Key1 non-articulatednon-sprung castoror wheel2 non-articulateddrive wheel3 sprun
42、g castoror wheelaParallel. bAny attainable combination ofliftheight,load and travelspeed thatproducesthe leasttilttable anglevalue for agiven tilttable anglerequirementoftests 1 and 2.Travelspeed vcan be zero.cAny attainable combination ofliftheightabove 1 200 mmand travelspeed thatproducesthe least
43、tilttable angle value foragiven tilttable angle requirementoftests3and 4.Travelspeed vcan be zero.dLiftheightuptoand including 1200 mm.eRequired tilttableangle for test1 when travelling load leading.fRequired tilttableangle for test1 when travelling load trailing.BS ISO 22915-21:2009ISO 22915-21:200
44、9(E) ICS 53.060 Price based on 7 pages ISO 2009 All rights reserved BS ISO 22915-21:2009This page has been intentionally left blank BS ISO22915-21:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the in
45、dependent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they
46、possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity
47、 of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and
48、 foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1