BS ISO 23480-2013 Tools for pressing Sliding plates《冲压工具 滑床台》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 23480:2013Tools for pressing SlidingplatesBS ISO 23480:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 23480:2013. Itsupersedes

2、 BS ISO 23480:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all

3、the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 76979 5ICS 25.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Stand

4、ard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2013.Amendments issued since publicationDate Text affectedBS ISO 23480:2013 ISO 2013Tools for pressing Sliding platesOutillage de presse Plaques de retenueINTERNATIONAL STANDARDISO23480Second edition2013-

5、03-01Reference numberISO 23480:2013(E)BS ISO 23480:2013ISO 23480:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or

6、mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749

7、01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 23480:2013ISO 23480:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 Type A, one-face sliding plates 13.2 Type B, two-face sliding plat

8、es 44 Material 55 Designation 5BS ISO 23480:2013ISO 23480:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical co

9、mmittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with th

10、e International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft Internation

11、al Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the

12、 subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 23480 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding.This second edition cancels and replaces the first edition (ISO 23480:20

13、08), Figures 1, 2 and 3 of which have been technically revised.iv ISO 2013 All rights reservedBS ISO 23480:2013INTERNATIONAL STANDARD ISO 23480:2013(E)Tools for pressing Sliding plates1 ScopeThis International Standard specifies the main dimensions and tolerances of sliding plates, to be used in pre

14、ss tools (an application example is shown in Figure 1).It also specifies the designation of sliding plates.Key1 sliding plates, type A2 sliding plates, type BFigure 1 Application example of sliding plates2 Normative referencesThe following documents, in whole or in part, are normatively referenced i

15、n this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimension

16、s without individual tolerance indicationsISO 4762, Hexagon socket head cap screwsISO 13715, Technical drawings Edges of undefined shape Vocabulary and indications3 Dimensions3.1 Type A, one-face sliding platesThe dimensions of one-face sliding plates, type A, shall conform to the indications in Fig

17、ure 2 and Table 1.All edges of undefined shape shall be in accordance with ISO 13715. ISO 2013 All rights reserved 1BS ISO 23480:2013ISO 23480:2013(E)General tolerance: ISO 2768-mDimensions in millimetresSurface roughness values in micrometresFigure 2 Type A, one-face sliding plates2 ISO 2013 All ri

18、ghts reservedBS ISO 23480:2013ISO 23480:2013(E)Table 1 Dimensions of one-face sliding plates, type ADimensions in millimetresb1020,h 0,2l10,2b2l2l3l4d Hexagon socketISO 4762 pieces35 1016020 4570 11 M10 302200 110 250 80 345 1516030 4570 13,5 M12 402200 110 250 80 355 1516035 4570 17,5 M16 502200 11

19、0 250 80 375 2516040 4570 17,5 M16 602200 110 250 80 3100 2516060 4570 17,5 M16 602200 110 250 80 3400 80 75 5100 3016060 4570 22 M20 702200 110 250 80 3400 80 75 5125 2516075 4570 17,5 M16 602200 110 250 80 3400 80 75 5125 3016075 4570 22 M20 702200 110 250 80 3400 80 75 5 ISO 2013 All rights reser

20、ved 3BS ISO 23480:2013ISO 23480:2013(E)3.2 Type B, two-face sliding platesThe dimensions of two-face sliding plates, type B, shall conform to the indications in Figure 3 and Table 2.All edges of undefined shape shall be in accordance with ISO 13715.General tolerance: ISO 2768-mDimensions in millimet

21、resSurface roughness values in micrometresFigure 3 Type B, two-face sliding plates4 ISO 2013 All rights reservedBS ISO 23480:2013ISO 23480:2013(E)Table 2 Dimensions of two-face sliding plates, type BDimensions in millimetresb1020,h 020,l1l2l3b2d1H13d2H13h1005+ ,Hexagon socketISO 4762 pieces25 121102

22、56012,5 9 15 8,5 M8 20 2120 7025 15110256012,5 11 18 10,5 M10 25 2120 7060 30125257530 13,5 20 13 M12 35 2160 110200 75 30 13,5 20 13 M12 35 360 40125257530 13,5 20 13 M12 452160 110 2200 75 34 MaterialThe choice of material is left to the manufacturers discretion.EXAMPLE Steel for type A sliding pl

23、ate and bronze with embedded solid lubricant for type B sliding plate.5 DesignationSliding plates in accordance with this International Standard shall be designated by:a) “Sliding plate”;b) a reference to this International Standard (i.e. ISO 23480);c) the type, A or B;d) the width, b1, in millimetr

24、es;e) the height, h, in millimetres;f) the length, l1, in millimetres.EXAMPLE 1 A sliding plate of type A with width b1= 100 mm, height h = 25 mm, and length l1= 250 mm is designated as follows:Sliding plate ISO 23480 A 100 25 250EXAMPLE 2 A sliding plate of type B with width b1= 60 mm, height h = 3

25、0 mm, and length l1= 125 mm is designated as follows:Sliding plate ISO 23480 B 60 30 125 ISO 2013 All rights reserved 5BS ISO 23480:2013ISO 23480:2013(E) ISO 2013 All rights reservedICS 25.120.10Price based on 5 pagesThis page deliberately left blankBSI is the independent national body responsible f

26、or preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards

27、Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the

28、latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which ca

29、n be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of Briti

30、sh Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addresse

31、d to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide ran

32、ge of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For det

33、ails of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI we

34、bsite at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed

35、such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior writt

36、en permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: