BS ISO 23519-2010 Sintered metal materials excluding hardmetals - Measurement of surface roughness《硬质合金除外的烧结金属材料 表面光洁度测量》.pdf

1、BS ISO23519:2010ICS 77.160NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSintered metalmaterials, excludinghardmetals Measurement ofsurface roughnessThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June201

2、0 BSI 2010ISBN 978 0 580 61817 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 23519:2010National forewordThis British Standard is the UK implementation of ISO 23519:2010.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/65, Sintered metal components.

3、A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom leg

4、al obligations.BS ISO 23519:2010Reference numberISO 23519:2010(E)ISO 2010INTERNATIONAL STANDARD ISO23519First edition2010-06-01Sintered metal materials, excluding hardmetals Measurement of surface roughness Matriaux mtalliques fritts, lexclusion des mtaux-durs Mesurage de la rugosit de surface BS IS

5、O 23519:2010ISO 23519:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editi

6、ng. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be f

7、ound in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at t

8、he address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from eit

9、her ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 23519:2010ISO 2

10、3519:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Symbols and units.2 5 Principle2 6 Procedure.3 7 Expression of results4 Bibliography5 BS ISO 23519:2010ISO 23519:2010(E) iv ISO 2010 All rights reservedForeword ISO (t

11、he International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical commit

12、tee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotech

13、nical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member

14、 bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

15、 any or all such patent rights. ISO 23519 was prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 3, Sampling and testing methods for sintered metal materials (excluding hardmetals). BS ISO 23519:2010INTERNATIONAL STANDARD ISO 23519:2010(E) ISO 2010 All rights reserved 1Si

16、ntered metal materials, excluding hardmetals Measurement of surface roughness 1 Scope This International Standard specifies a method to determine the surface roughness of sintered parts of metal materials. It also establishes principles for the use of the suitable parameters for measurement. 2 Norma

17、tive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4287, Geometrical Product Spe

18、cification (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters ISO 13565-1, Geometrical Product Specifications (GPS) Surface texture: Profile method; Surface having stratified functional properties Part 1: Filtering and general measurement conditions ISO 13565-2,

19、Geometrical Product Specifications (GPS) Surface texture: Profile method; Surfaces having stratified functional properties Part 2: Height characterization using the linear material ratio curve ISO 13565-3, Geometrical Product Specifications (GPS) Surface texture: Profile method; Surfaces having stra

20、tified functional properties Part 3: Height characterization using the material probability curve 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 4287 apply. BS ISO 23519:2010ISO 23519:2010(E) 2 ISO 2010 All rights reserved4 Symbols and units For the

21、 purposes of this document, the following symbols and units apply. Symbol Quantity Unit Rpk Reduced peak height m Rp Maximum profile peak height m Rv Maximum profile valley depth m Rz Maximum height of profile m Rt Total height of profile m Ra Arithmetic mean deviation of the assessed profile m Rq R

22、oot mean square deviation of the assessed profile m Rs Surface roughness m RSm Mean width of the profile elements m Rmr(c) Material ratio of the profile % Rk Core roughness depth mRvk Reduced valley depth m d Density g/cm3c Level m5 Principle The surface roughness is measured according to standard p

23、rocedures. Because of the porosity and the nature of the surface of sintered materials, their surface roughness cannot be compared with the surface roughness of wrought materials. As most of the roughness parameters are defined by measuring the height of the surface peaks, porosity will negatively i

24、nfluence this value, because the depth of the pore will increase the value of the peak. This International Standard specifies the most suitable way to measure surface roughness and the correct parameters to use. BS ISO 23519:2010ISO 23519:2010(E) ISO 2010 All rights reserved 36 Procedure The surface

25、 roughness shall be measured in accordance with ISO 13565-1, ISO 13565-2 and ISO 13565-3, by using the following particular parameters: a) always use a filtered profile (roughness profile), by applying the standard Gaussian filter, with a cut-off of 0,8 mm; b) use a total evaluation length of 4 mm,

26、which is five times the cut-off value of 0,8 mm; NOTE Only in the case of a roughness higher than 4,0 Ra, the cut-off will be increased up to 2,5 mm, so the new evaluation length will be 12,5 mm. This is because the surface is so irregular that a longer evaluation length is necessary to obtain a rea

27、l statistical approach. c) use a probe with a radius of 2 m that will define the surface irregularities as well as possible; d) express the results as parameters Rk and Rpk, in micrometres. Roughness parameters that are strongly affected by porosity, which do not really characterize the surface stat

28、e, but rather the addition between the surface state and the size of the open porosity, shall not be used. This is the case for Rp, Rv, Rz, Rt, Ra, Rq, Rs and RSm. In order to illustrate the convenience of Rpk and the inconvenience of other parameters typical for wrought materials, a comparison betw

29、een different materials and surface conditions is shown in Table 1. BS ISO 23519:2010ISO 23519:2010(E) 4 ISO 2010 All rights reservedTable 1 Comparison of roughness of powder metallurgy (PM) material with wrought materials Material Surface profile BACacurve supporting surface Roughness Ra = 1,22 Rt

30、= 10,6 Rmr(3) = 91 %Rpk = 0,8 Rk = 0,6 Sintered and sized d = 6,6 g/cm3Figure 1 Surface profile Sintered and sized Figure 2 BAC curve Sintered and sized Rvk = 9,1 Ra = 1,28 Rt = 10,7 Rmr(3) = 20 %Rpk = 4,5 Rk = 5,4 Turned solid material Figure 3 Surface profile Turned solid material Figure 4 BAC cur

31、ve Turned solid material Rvk = 0,6 Ra = 0,6 Rt = 4,2 Rmr(3) = 83 %Rpk = 1,3 Rk = 1,4 Ground solid material Figure 5 Surface profile Ground solid material Figure 6 BAC curve Ground solid material Rvk = 1,3 NOTE The way to obtain the BAC curve and to determine the Rpk- and Rvk-roughness parameters are

32、 described in ISO 4287 and ISO 13565-2. aBAC: Bearing area curve. 7 Expression of results The result is the surface roughness, expressed as parameters Rk and Rpk, in micrometres. The result should be reported to the nearest 0,1 m. BS ISO 23519:2010ISO 23519:2010(E) ISO 2010 All rights reserved 5Bibl

33、iography 1 ISO 3274, Geometrical Product Specifications (GPS) Surface texture: Profile method Nominal characteristics of contact (stylus) instruments 2 ISO 4288, Geometrical Product Specifications (GPS) Surface texture: Profile method Rules and procedures for the assessment of surface texture 3 ISO

34、11562, Geometrical Product Specifications (GPS) Surface texture: Profile method Metrological characteristics of phase correct filters 4 ISO 12085, Geometrical Product Specification (GPS) Surface texture: Profile method Motif parameters BS ISO 23519:2010ISO 23519:2010(E) ICS 77.160 Price based on 5 p

35、ages ISO 2010 All rights reserved BS ISO 23519:2010This page has been intentionally left blank BS ISO23519:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for

36、preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions

37、.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside fro

38、nt cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should b

39、eaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have be

40、en published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also availabl

41、e whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof thes

42、e and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyrigh

43、t subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by

44、 anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: