BS ISO 24033-2009 Polyethylene of raised temperature resistance (PE-RT) pipes - Effect of time and temperature on the expected strength《耐升温的聚乙烯管道(PE-RT) 时间和温度对预期强度的影响》.pdf

1、BS ISO24033:2009ICS 23.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPolyethylene of raisedtemperature resistance(PE-RT) pipes Effect of time andtemperature on theexpected strengthThis British Standardwas published under theauthority of the StandardsPoli

2、cy and StrategyCommittee on 28 February2009 BSI 2009ISBN 978 0 580 57516 7Amendments/corrigenda issued since publicationDate CommentsBS ISO 24033:2009National forewordThis British Standard is the UK implementation of ISO 24033:2009.The UK participation in its preparation was entrusted to TechnicalCo

3、mmittee PRI/88/4, Test methods.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard

4、 cannot confer immunityfrom legal obligations.BS ISO 24033:2009Reference numberISO 24033:2009(E)ISO 2009INTERNATIONAL STANDARD ISO24033Second edition2009-01-15Polyethylene of raised temperature resistance (PE-RT) pipes Effect of time and temperature on the expected strength Tubes en polythylne de me

5、illeure rsistance la temprature (PE-RT) Influence du temps et de la temprature sur la rsistance espre BS ISO 24033:2009ISO 24033:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited

6、 unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trad

7、emark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodie

8、s. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any me

9、ans, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copy

10、rightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 24033:2009ISO 24033:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The wo

11、rk of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governm

12、ental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The

13、main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

14、Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 24033 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the

15、 transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic specifications. This second edition cancels and replaces the first edition (ISO 24033:2006), which is extended to cover PE-RT materials, type II

16、, which have a higher hoop stress performance at higher temperatures than type I. The first edition dealt only with PE-RT materials, currently designated type I. BS ISO 24033:2009ISO 24033:2009(E) iv ISO 2009 All rights reservedIntroduction An increasing number of types of polyethylene (PE) polymers

17、, made in a variety of processes, is on the market for different applications in plastic piping and ducting systems. Many applications have their own system standard that defines the properties and requirements for the pipes and fittings used. The types of PE suitable for use in hot and cold water s

18、ystems are basically different from those for applications at ambient temperatures such as in water supply, sewage and drainage, and gaseous fuels. Therefore, it makes sense to differentiate those PE having raised temperature-resistance by terming them “PE-RT” (for polyethylene of raised temperature

19、)1). See the foreword for details of PE-RT materials, types I and II. 1) Abbreviated term based on the provisions of, and guidance for preparing new abbreviated terms for, basic polymers, mixtures of polymers, and related terms given in ISO 1043-11. BS ISO 24033:2009INTERNATIONAL STANDARD ISO 24033:

20、2009(E) ISO 2009 All rights reserved 1Polyethylene of raised temperature resistance (PE-RT) pipes Effect of time and temperature on the expected strength 1 Scope This International Standard specifies minimum values for expected strength as a function of time and temperature in the form of reference

21、lines, for use in calculations on pipes made of: a) polyethylene of raised temperature resistance (PE-RT) type I; b) PE-RT type II. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.

22、For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics pipe

23、s, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 reference line PE-RT pipes generic descriptio

24、n of the minimum long-term hydrostatic strength to be expected from a particular polymer NOTE 1 A reference line is not to be considered as characteristic of a specific grade or of material from a specific supplier. NOTE 2 A line is described by a mathematical equation, which permits interpolation a

25、nd extrapolation in an unambiguous way at various temperatures. NOTE 3 The reference lines for PE-RT have been agreed by a group of experts after considering experimental data, and have been accepted by the relevant ISO technical committees. BS ISO 24033:2009ISO 24033:2009(E) 2 ISO 2009 All rights r

26、eserved4 Basic equations The reference lines for PE-RT type I temperatures between 20 C and 95 C are described by Equations (1) and (2): Ig t = A1+ (B1/T) Ig + C1/T + D1Ig (1) lg t = A2+ (B2/T) Ig + C2/T + D2Ig (2where t is the time, in hours; T is the temperature, in kelvin; is the hoop stress, in

27、megapascals; A1= 190,481 A2= 23,795 4 B1= 58 219,035 B2= 1 723,318 C1= 78 763,07 C2= 11 150,56 D1= 119,877 D2= 0 The 110 C values have been determined separately using water inside and air outside the test specimen and have not been derived from Equations (1) and (2). The reference lines for PE-RT t

28、ype II for temperatures between 20 C and 110 C are described by Equation (3): lg t = A + (B/T) lg + C/T + D lg (3) where A = 219 B = 62600,752 C = 90 635,353 D = 126,387 NOTE ISO 90802quotes equations in a different sequence where C1= A, C2= C, C3= D and C4= B. 5 Expected strength 5.1 Extrapolation

29、limits The extrapolation limits (the end points of the reference lines) are based on an experimentally determined life at 110 C and an Arrhenius equation for the temperature dependence with an activation energy of 110 kJ/mol ( 26 kcal/mol). This yields the values given in Table 1 for the extrapolati

30、on factor, Kx(i.e. the expected lifetime at a given temperature divided by the lifetime at 110 C). BS ISO 24033:2009ISO 24033:2009(E) ISO 2009 All rights reserved 3Table 1 Extrapolation factors, KxTemperature Extrapolation factor T KxC 100 W T 95 2,5 95 W T 90 4 90 W T 85 6 85 W T 80 12 80 W T 75 18

31、 75 W T 70 30 T u 70 50 With a life of 1 year at 110 C, these values are therefore the number of years the pipes would be expected to last at each of the temperatures given. For temperatures up to and including 50 C, an extrapolation factor Kxof 100 is acceptable. 5.2 Graphical representation Figure

32、 1 and Figure 2 contain the reference lines corresponding to the values of the parameters given in Clause 4, to be used for demonstrating conformity to this specification, as specified in Annex A. The broken lines represent the extrapolation of the reference lines, applicable when longer failure tim

33、es are obtained at 110 C, extrapolation being permitted up to the limits given by the extrapolation factors in Table 1. 5.3 Tabulated values The calculated hoop strength values to be used for various temperatures and times are given in Table 2 and include no safety factors or design factors. The tim

34、es at 80 C, 90 C and 95 C not in brackets in the “Time” column in Table 2 are based on a lifetime of one year at 110 C. Proof of a longer lifetime at 110 C allows a corresponding extension of the times at lower temperatures. Such values are given in brackets in Table 2. BS ISO 24033:2009ISO 24033:20

35、09(E) 4 ISO 2009 All rights reservedTable 2 Expected hoop strength values for various values of time and temperature for PE-RT Temperature C Time a Expected strength MPa TemperatureC Time a Expected strength MPa Type I Type II Type I Type II 20 1 5 10 25 50 100 8,8 8,6 8,5 8,4 8,3 8,3 9,8 9,6 9,5 9,

36、4 9,3 9,3 70 1 5 10 25 50 5,1 4,8 4,8 4,7 4,1 5,4 5,3 5,2 5,1 5,1 30 1 5 10 25 50 100 8,1 7,9 7,8 7,7 7,6 7,6 8,9 8,7 8,6 8,5 8,5 8,4 80 1 5 10 18 (25) 4,3 4,2 3,8 3,4 (3,2) 4,6 4,5 4,4 4,3 (4,3) 40 1 5 10 25 50 100 7,3 7,2 7,1 7,0 6,9 6,8 8,0 7,8 7,8 7,7 7,6 7,5 90 1 4 6 (10) (15) 3,6 3,1 2,9 (2,6)

37、 (2,4) 3,8 3,7 3,6 (3,6) (3,6) 50 1 5 10 25 50 100 6,6 6,4 6,3 6,2 6,2 6,1 7,2 7,0 6,9 6,8 6,7 6,7 95 1 4 (6) (10) 3,2 2,6 (2,4) (2,1) 3,4 3,3 (3,3) (3,2) 60 1 5 10 25 50 5,8 5,7 5,6 5,5 5,4 6,3 6,1 6,1 6,0 5,9 BS ISO 24033:2009ISO 24033:2009(E) ISO 2009 All rights reserved 5Key X1t1time to fracture

38、, h X2t2time to fracture, a Y hoop stress, MPa Figure 1 Expected strength of PE-RT type I pipes BS ISO 24033:2009ISO 24033:2009(E) 6 ISO 2009 All rights reservedKey X1t1time to fracture, h X2t2time to fracture, a Y hoop stress, MPa Figure 2 Expected strength of PE-RT type II pipes BS ISO 24033:2009I

39、SO 24033:2009(E) ISO 2009 All rights reserved 7Annex A (normative) Demonstrating conformity of pipes to reference lines At each of the following temperatures, specimens shall be tested at each of the temperatures given; at least three failure times shall fall in each of the following time intervals:

40、 Temperatures: 20 C, 60 C to 82 C, 95 C and, for type II, 110 C NOTE 82 C is equivalent to 180F, commonly used as a test temperature in ASTM standards. Time intervals: 10 h to 100 h 100 h to 1000 h 1 000 h to 8760 h 8760 h In the case of tests lasting longer than 8 760 h, any test time after this va

41、lue may be considered as the failure time. Testing shall be carried out in accordance with ISO 1167-1 and ISO 1167-2. Conformity to reference lines shall be demonstrated by plotting the individual experimental results on the graph. At least 97,5 % of them shall lie on or above the reference lines gi

42、ven in either Figure 1 or Figure 2. For PE-RT type II materials, these experimental results shall not give any brittle failures indicating the presence of a knee at any temperature up to 110 C within 8 760 h. BS ISO 24033:2009ISO 24033:2009(E) 8 ISO 2009 All rights reservedBibliography 1 ISO 1043-1,

43、 Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics 2 ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation BS ISO 24033:2009BS ISO 24033:2009ISO 24033:2

44、009(E) ICS 23.040.20 Price based on 8 pages ISO 2009 All rights reserved BS ISO 24033:2009This page has been intentionally left blank BS ISO24033:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the ind

45、ependent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they p

46、ossess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity

47、of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and

48、foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational