BS ISO 24453-2008 Rubber - Acquisition and presentation of comparable single-point data《橡胶 可比单点数据的采集和表示》.pdf

1、BS ISO24453:2008ICS 83.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRubber Acquisitionand presentation ofcomparable single-point dataThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 August2008 BSI 200

2、8ISBN 978 0 580 58339 1Amendments/corrigenda issued since publicationDate CommentsBS ISO 24453:2008National forewordThis British Standard is the UK implementation of ISO 24453:2008. Itsupersedes BS 903-3:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommit

3、tee PRI/22, Physical testing of rubber.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British

4、Standard cannot confer immunityfrom legal obligations.BS ISO 24453:2008Reference numberISO 24453:2008(E)ISO 2008INTERNATIONAL STANDARD ISO24453First edition2008-05-01Rubber Acquisition and presentation of comparable single-point data Caoutchouc Acquisition et prsentation de donnes simples comparable

5、s BS ISO 24453:2008ISO 24453:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing th

6、e editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file c

7、an be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretari

8、at at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing f

9、rom either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedBS ISO 24453:20

10、08ISO 24453:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 3 4 Test piece preparation 3 5 Conditioning 3 6 Processability properties. 4 7 Test requirements. 4 8 Presentation of results. 5 Bibliography . 8 BS ISO 24453

11、:2008ISO 24453:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.

12、Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internat

13、ional Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Stand

14、ards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subjec

15、t of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 24453 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 2, Testing and analysis. BS ISO 24453:2008INTERNATIONAL STANDARD ISO 24453:2008(E) ISO 2008 All ri

16、ghts reserved 1Rubber Acquisition and presentation of comparable single-point data 1 Scope This International Standard identifies specific test procedures for the acquisition and presentation of comparable single-point data for properties of rubber compounds. In general, each property is specified b

17、y a single test method and a single experimental value although, in certain cases, properties may be represented by more than one value obtained under different test conditions. The properties presented are those used to characterize processing properties, those most often quoted by manufacturers an

18、d in material specifications, and those relevant to more specific applications. An important application of this International Standard consists in helping different suppliers produce material specification sheets in which the same set of properties is measured using the same conditions. 2 Normative

19、 references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 34-1, Rubber, vulcanized or therm

20、oplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces ISO 36, Rubber, vulcanized or thermoplastic Determination of adhesion to textile fabric ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties ISO 48, Rubber, vulcanized or

21、thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 289-1, Rubber, unvulcanized Determinations using a shearing-disc viscometer Part 1: Determination of Mooney viscosity ISO 289-

22、2, Rubber, unvulcanized Determinations using a shearing-disc viscometer Part 2: Determination of pre-vulcanization characteristics ISO 812, Rubber, vulcanized or thermoplastic Determination of low-temperature brittleness ISO 813, Rubber, vulcanized or thermoplastic Determination of adhesion to a rig

23、id substrate 90 peel method ISO 815-1, Rubber, vulcanized or thermoplastic Determination of compression set at ambient, elevated or low temperatures Part 1: At ambient or elevated temperatures ISO 815-2, Rubber, vulcanized or thermoplastic Determination of compression set at ambient, elevated or low

24、 temperatures Part 2: At low temperatures BS ISO 24453:2008ISO 24453:2008(E) 2 ISO 2008 All rights reservedISO 1431-1, Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing ISO 1432, Rubber, vulcanized or thermoplastic Determination of low tempera

25、ture stiffening (Gehman test) ISO 1817, Rubber, vulcanized Determination of the effects of liquids ISO 1827, Rubber, vulcanized or thermoplastic Determination shear modulus adhesion to rigid plates Quadruple-shear method ISO 1853, Conducting and dissipative rubbers, vulcanized or thermoplastic Measu

26、rement of resistivity ISO 2007, Rubber, unvulcanized Determination of plasticity Rapid-plastimeter method ISO 2285, Rubber, vulcanized or thermoplastic Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load ISO 2393, Rubber test m

27、ixes Preparation, mixing and vulcanization Equipment and procedures ISO 2781, Rubber, vulcanized and thermoplastic Determination of density ISO 2782, Rubber, vulcanized or thermoplastic Determination of permeability to gases ISO 2921, Rubber, vulcanized Determination of low-temperature characteristi

28、cs Temperature-retraction procedure (TR test) ISO 3384, Rubber, vulcanized or thermoplastic Determination of stress relaxation in compression at ambient and elevated temperatures ISO 3387, Rubber Determination of crystallization effects by hardness measurements ISO 3865, Rubber, vulcanized or thermo

29、plastic Methods of test for staining in contact with organic material ISO 4649, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device ISO 4662, Rubber Determination of rebound resilience of vulcanizates ISO 4666-3, Rubber, vulcanized Determ

30、ination of temperature rise and resistance to fatigue in flexometer testing Part 3: Compression flexometer ISO 6179, Rubber, vulcanized or thermoplastic Rubber sheets and rubber-coated fabrics Determination of transmission rate of volatile liquids (gravimetric technique) ISO 6502, Rubber Guide to th

31、e use of curemeters ISO 7743, Rubber, vulcanized or thermoplastic Determination of compression stress-strain properties ISO 8013, Rubber, vulcanized Determination of creep in compression or shear ISO 9026, Raw rubber or unvulcanized compounds Determination of green strength ISO 11345, Rubber Assessm

32、ent of carbon black and carbon black/silica dispersion Rapid comparative methods ISO 15113, Rubber Determination of frictional properties ISO 23529, Rubber General procedures for preparing and conditioning test pieces for physical test methods BS ISO 24453:2008ISO 24453:2008(E) ISO 2008 All rights r

33、eserved 3IEC 60093, Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials BS 903:A18, Physical testing of rubber Part A18: Determination of equilibrium water vapour absorption 3 Terms and definitions For the purposes of this document, the following t

34、erms and definitions apply. 3.1 single-point data data characterizing a rubber material by means of those property tests in which important aspects of performance can be described with single-value results 4 Test piece preparation Where relevant, materials for test shall be prepared, mixed and mould

35、ed following the general principles given in ISO 2393. The detailed conditions used shall be as recommended by the manufacturer of the rubber compound and shall, for each of the processing steps, be the same for each test piece except that different cure times may be used for different sized test pi

36、eces. The equipment, mixing cycle and conditions used for moulding shall be given in the test report. The final preparation of test pieces (for example stamping from sheet) shall be in accordance with the relevant test method standard. The properties of a rubber compound can vary depending on the pr

37、ocessing procedures used and this should be taken into account when comparing materials. To maximize the usefulness of results, processing conditions should be representative of those used in production. 5 Conditioning The time between mixing and moulding shall be between 24 h and one week. The time

38、 between moulding and conditioning shall be between 16 h and four weeks. Recommendations for the storage of vulcanized rubber products are given in ISO 2230. Test pieces shall be conditioned in accordance with the relevant test method standard. Where this refers to standard laboratory conditions of

39、temperature and/or humidity, these are taken to mean (23 2) C and 50 % RH. NOTE If tests are carried out at the alternative standard laboratory temperature of (27 2) C, the results will not be strictly comparable unless adjusted by the known relationship of the property with temperature. For tests a

40、t temperatures other than (23 2) C, where specific instructions are not included in the test method standard, condition the test pieces at the temperature at which the test is to be conducted for a period sufficient to enable test pieces to attain substantial equilibrium in accordance with ISO 23529

41、. Details of the conditioning used shall be given in the test report. BS ISO 24453:2008ISO 24453:2008(E) 4 ISO 2008 All rights reserved6 Processability properties If processability data are required (for example if unvulcanized material is being supplied), the test methods, test conditions and units

42、 shall be selected from those specified in Table 1. The test temperature(s) shall be as considered appropriate for the material in question. NOTE The measurement of viscoelastic flow and cure properties of rubber compounds is essential for the processor in order to form the material efficiently and

43、effectively into the required product. However, these properties are generally of little consequence for the end user of the product and it is for this reason that processability properties are considered separately to other properties in this International Standard. Table 1 Test methods for process

44、ability data Property Symbol International Standard Unit Test conditions 1.1 Mooney viscosity See ISO 289-1 ISO 289-1 Mooney units Large rotor 1.2 Mooney scorch time txISO 289-2 min Rise of 5 MU 2.1 Rapid plasticity number ISO 2007 0,01 mm 3.1 Time to 90 % cure (The cure curve is normally presented.

45、) tc(90) ISO 6502 min 3.2 Time to 50 % cure tc(50) ISO 6502 min 3.3 Scorch time tsxISO 6502 min 3.4 Minimum torque MLISO 6502 Nm 3.5 Plateau torque (Maximum torque or torque after a specified time, if appropriate) MHF(MHRor MH) ISO 6502 Nm Preference is given to an oscillating die instrument. The te

46、mperature is selected according to the compound and expected processing conditions. 4.1 Green strength (yield or maximum stress) ISO 9026 MPa Use beaded type 1 test piece. 4.2 Carbon black dispersion ISO 11345 Dimensionless Method A or B 7 Test requirements The test methods, test conditions and unit

47、s specified in Table 2 shall be used when determining data according to this International Standard. A property may be omitted if it is not relevant to the material in question (for example fluid resistance, if a compound is not for use in oil or fuel). It is not essential to measure both compressio

48、n and tension set, the choice being dependent on the material and the intended application. If required, additional properties may be presented using the test methods, test conditions and units specified in Table 3. It is recommended that all properties relevant to the intended end use of the materi

49、al be presented. BS ISO 24453:2008ISO 24453:2008(E) ISO 2008 All rights reserved 5Unless otherwise specified in the tables or the test method standard, properties shall be measured at standard laboratory temperature and, where appropriate, humidity, in an air atmosphere in accordance with ISO 23529. NOTE 1 The properties listed in Table 2 are those usually included in data sheets whilst those listed in Table 3 will generally only