BS ISO 24631-5-2014 Radio frequency identification of animals Procedure for testing the capability of RFID transceivers of reading ISO 11784 and ISO 11785 transponders《动物射频识别 读取ISO.pdf

1、BSI Standards PublicationBS ISO 24631-5:2014Radio frequency identificationof animalsPart 5: Procedure for testing the capabilityof RFID transceivers of reading ISO 11784and ISO 11785 transpondersBS ISO 24631-5:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of IS

2、O 24631-5:2014.The UK participation in its preparation was entrusted to TechnicalCommittee AGE/6/1, Radio Frequency ID for Animals.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions

3、 of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 71824 3ICS 65.040.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under

4、 the authority of theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS ISO 24631-5:2014 ISO 2014Radio frequency identification of animals Part 5: Procedure for testing the capability of RFID transceivers of reading ISO 11784 and ISO 1

5、1785 transpondersIdentification des animaux par radiofrquence Partie 5: Procdure pour vrifier les capacits des metteurs-rcepteurs lire des transpondeurs RFID conformes lISO 11784 et lISO 11785INTERNATIONAL STANDARDISO24631-5First edition2014-12-15Reference numberISO 24631-5:2014(E)BS ISO 24631-5:201

6、4ISO 24631-5:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on th

7、e internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb

8、 www.iso.orgPublished in SwitzerlandBS ISO 24631-5:2014ISO 24631-5:2014(E)Contents PageForeword ivIntroduction v1 Scope . 12 Conformance . 13 Normative reference . 14 Terms and definitions . 25 Abbreviations. 36 Application . 37 Test procedures . 47.1 Frequency of activation field . 47.2 Functional

9、test . 47.3 Timing of the activation field 57.4 Test setup and test equipment 57.5 Test conditions 7Annex A (normative) Test application form . 8Annex B (informative) Conditions of use of transceiver approval . 9Bibliography .11 ISO 2014 All rights reserved iiiBS ISO 24631-5:2014ISO 24631-5:2014(E)F

10、orewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec

11、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o

12、f electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document

13、 was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such paten

14、t rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not consti

15、tute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword Supplementary information.The commi

16、ttee responsible for this document is ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 19, Agricultural electronics.ISO 24631 consists of the following parts, under the general title Radio frequency identification of animals: Part 1: Evaluation of conformance of RFID t

17、ransponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code) Part 2: Evaluation of conformance of RFID transceivers with ISO 11784 and ISO 11785 Part 3: Evaluation of performance of RFID transponders conforming with ISO 11784 and ISO 11785 Part 4: Evaluation of perfor

18、mance of RFID transceivers conforming with ISO 11784 and ISO 11785 Part 5: Procedure for testing the capability of RFID transceivers of reading ISO 11784 and ISO 11785 transponders Part 6: Representation of animal identification information (visual display/data transfer) Part 7: Synchronization of I

19、SO 11785 identification systemsiv ISO 2014 All rights reservedBS ISO 24631-5:2014ISO 24631-5:2014(E)IntroductionISO has appointed ICAR (International Committee for Animal Recording) as the registration authority (RA) competent to register manufacturer codes used in the radio frequency identification

20、 (RFID) of animals in accordance with ISO 11784 and ISO 11785.ISO 24631 defines means, based upon ICAR test procedures1, for evaluating and verifying both the conformance and performance of RFID devices in respect of ISO 11784 and ISO 11785. Only those results emanating from RA-approved test centres

21、 are recognized.This part of ISO 24631 deals with the capability of RFID transceivers of reading ISO 11784 and ISO 11785 transponders. ISO 2014 All rights reserved vBS ISO 24631-5:2014BS ISO 24631-5:2014Radio frequency identification of animals Part 5: Procedure for testing the capability of RFID tr

22、ansceivers of reading ISO 11784 and ISO 11785 transponders1 ScopeThis part of ISO 24631 specifies rules and procedures for verifying the capability of RFID transceivers of reading transponders used in individual animal identification complying to ISO 11784 and ISO 11785. In addition, this part of IS

23、O 24631 specifies how to apply for an approval and the rights and duties to use this approval. This part of ISO 24631 does not set out the procedures for evaluating wireless synchronised mobile transceivers and also this document contains no provision for evaluating wired synchronisation of stationa

24、ry transceivers.This test differs from ISO 24631-2, which is intended for testing transceivers with all mandatory features described in ISO 11784 and ISO 11785. The test described here is intended for cost-effective non-synchronising transceivers that are capable of reading transponders complying to

25、 ISO 11784 and ISO 11785 but have no synchronisation capability and does not have to support the dual adaptive protocol. Furthermore, the activation field frequency accuracy is more relaxed. 2 ConformanceThe procedures of this part of ISO 24631 include the options of RA approval and registration of

26、transceiver equipment. The procedures of this part of ISO 24631 shall be followed if a company wants RA approval and registration of a transceiver.The test procedures given in Clause 7 of this part of ISO 24631 specify the procedure how to verify RFID-transceivers capability of reading transponders

27、complying to ISO 11784 and ISO 11785. RA-approved test centres carry out transceiver tests in conformance with these procedures and report the results to the RA. A transceiver test approval is granted to a company whose transceiver product has passed the tests mentioned in Clause 7. Approved transce

28、iver products receive an approval reference number. To apply for an approval reference number, an application form (Annex A) shall be completed, signed, and submitted to the RA. In order to standardize the use of the test approval, the conditions for the right of using this approval are given in Ann

29、ex B.3 Normative referenceThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any am

30、endments) applies.ISO 3166-1, Codes for the representation of names of countries and their subdivisions Part 1: Country codesISO 11784:1996, Radio frequency identification of animals Code structureISO 11785:1996, Radio frequency identification of animals Technical conceptISO 24631-1:2009, Radiofrequ

31、ency identification of animals Part 1: Evaluation of conformance of RFID transponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code)INTERNATIONAL STANDARD ISO 24631-5:2014(E) ISO 2014 All rights reserved 1BS ISO 24631-5:2014ISO 24631-5:2014(E)4 Terms and definitions

32、For the purposes of this document, the following terms and definitions apply.4.1approval reference numbernumber issued to the manufacturer of an approved transceiver by the registration authorityEXAMPLE 246315 2009001Note 1 to entry: It comprises the reference of the International Standard for which

33、 approval is made, the year of issue (four digits) and the running number (three digits), referencing the transceivers tested successfully during that year.4.2country codethree-digit numeric code representing the name of a country in accordance with ISO 3166-14.3ISO 11784 and ISO 11785 transceivertr

34、ansceiver that reads at least both ISO FDX-B and ISO HDX transponders as defined in ISO 11784 and ISO 117854.4ISO 11784 and ISO 11785 transponderradio frequency identification (RFID) device that transmits its transponder code according to ISO 11784 and ISO 11785 when activated by a transceiver4.5man

35、ufacturercompany that submitted the application for conformance testing in conformance with ISO 11784 and ISO 117854.6manufacturer codethree-digit number granted by the RA to a manufacturer under the conditions set forth in ISO 24631-1:2009, Annex E, whose range and placement within the code structu

36、re are in accordance with ISO 11784Note 1 to entry: Only one manufacturer code is granted to the same manufacturer.4.7RA-approved test centreaccredited test centre meeting the criteria of the registration authorityNote 1 to entry: Accreditation: third-party attestation related to a conformity assess

37、ment body conveying formal demonstration of its competence to carry out specific conformity assessment tasks (see Reference 2).4.8RA-approved transpondertransponder approved by the registration authority4.9reference transpondertransponder that is used to test a transceiver, selected from the differe

38、nt RA-approved transponder types4.10registration authorityRAentity that approves test laboratories and issues and registers manufacturer and product codes2 ISO 2014 All rights reservedBS ISO 24631-5:2014ISO 24631-5:2014(E)4.11transceiverdevice used to communicate with the transponder4.12transponderr

39、adio frequency identification (RFID) device that transmits its stored information when activated by a transceiver and that may be able to store new informationNote 1 to entry: See ISO 24631-1 for definitions of the main types.4.13transponder codecode as programmed in the transponder and defined in I

40、SO 11784:1996, Table 1 and ISO 117855 AbbreviationsCRC cyclic redundancy checkFDX-B full duplex communication protocol (conforming to ISO 11785, excluding protocols mentioned in ISO 11785:1996, Annex A).HDX half duplex communication protocolMFC manufacturer codeRA registration authorityRF radio freq

41、uencyRFID radio frequency identification6 Application6.1 The manufacturer can apply for a conformance test for a transceiver capable of reading ISO 11784 and ISO 11785 transponders.6.2 The application submitted to the RA shall consist of a covering letter together with the application form presented

42、 in Annex A. The RA shall confirm receipt of the application to the manufacturer within two weeks. By signing the application form, the manufacturer agrees to fulfil the provisions of this part of ISO 24631.6.3 The test centres shall be approved by the RA.6.4 The RA maintains a list of approved test

43、 centres, from which the manufacturer may choose the centre that will test his transceiver product.6.5 The manufacturer shall send a transceiver and all the necessary accessories to the RA-approved test centre. The manufacturer shall ensure that the equipment is able to display or store the transpon

44、der codes during the test.6.6 The RA-approved test centre shall verify the transceivers using the test procedures specified in Clause 7. All reference transponders shall be readable by the transceiver under test. The codes read shall match the known codes of the reference transponders.6.7 The RA-app

45、roved test centre shall prepare a confidential report of the results and shall send two copies (and an electronic version) of the report to the chairman of the RA. ISO 2014 All rights reserved 3BS ISO 24631-5:2014ISO 24631-5:2014(E)6.8 The RA Chairman shall inform the manufacturer of the test result

46、s in a letter together with a copy of the report.6.9 The RA shall issue an approval reference number for each conformant transceiver type and model.6.10 The tested transceivers shall be kept by the test centre, under the ownership of the RA.6.11 The RA shall make publicly available a list of conform

47、ant transceivers. A photograph of the approved transceiver shall be included in the list.6.12 The RA shall do everything within its power to protect the integrity of this procedure with regard to ISO 11784 and ISO 11785.7 Test proceduresThe test procedure that shall be applied is the same for every

48、transceiver capable of reading ISO 11784 and ISO 11785 transponders. Transceivers shall meet the technical criteria.This type of transceivers shall be named: “transceivers capable of reading transponders conforming to ISO 11784/11785”.IMPORTANT As there may be electronic interference between transce

49、ivers, this type of transceiver shall not be operated within a distance of 10 m from any ISO transceiver. The non-synchronising transceiver shall be marked as such by a label, clearly designating the transceiver as a non-synchronising transceiver and shall carry the warning mentioned above.For documentation, a photograph of the transceiver shall be taken and included in the final test report. Additionally, weight, dimensions, and the device serial number shall be noted in the test report.7.1 Frequency of activation fiel