BS ISO 254-2011 Belt drives Pulleys Quality finish and balance《皮带传动 皮带轮 质量、精整和平衡》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 254:2011Belt drives Pulleys Quality, finish and balanceBS ISO 254:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 254:2011. Its

2、upersedes BS ISO 254:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/10, Belts it does not apply to those pulleys for variable speed drives that have one or more moving flanges.The other characteristics of transmission pulleys can be found in t

3、he relevant International Standards.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

4、applies.ISO 1940-1, Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerancesISO 4287, Geometrical Product Specifications (GPS) Surface texture: Profile method Terms, definitions and surface texture parameter

5、s 3 Choice and quality of materialsThe pulleys shall be made of any material that can be shaped to the standardized dimensions and tolerances, and is capable of withstanding the conditions of service (heating, mechanical stresses, abrasion, environment, etc.) without damage. Moreover, it is desirabl

6、e that the pulley material be capable of dissipating any significant heat which can be generated by the belts.4 Surface roughness4.1 Transmission pulleysThe surface roughness of the working surfaces shall not be coarser than the value given in Table 1.Table 1 Transmission pulleysWorking surface Surf

7、ace roughness, RaamV-pulley and V-ribbed pulley grooves and all pulley bores 3,2Flat pulley rims and all pulley rim edges 6,3Synchronous pulley tooth flanks and tips: industrial type drives 3,2 high-performance type drives (for example for automotive applications)1,6aAs defined in ISO 4287. ISO 2011

8、 All rights reserved 1BS ISO 254:20114.2 Test pulleysThe surface roughness of the working surfaces shall not be coarser than the value given in Table 2.Table 2 Test pulleysWorking surface Surface roughness, RaamV-pulley and V-ribbed pulley grooves (dynamic test) 1,6Synchronous pulley grooves 1,6Idle

9、r pulleys 1,6aAs defined in ISO 4287.4.3 EdgesThe edges of flat pulley rims, V-pulley grooves and V-ribbed pulley grooves shall be chamfered or radiused.5 Balance5.1 The purpose of balancing a pulley is to improve its mass distribution so as to diminish the out-of-balance forces exerted as it revolv

10、es; these forces cannot be completely eliminated, but the remaining imbalance shall not be greater than the allowable limit.5.2 As balancing is an expensive operation, the specified limit of the residual imbalance should be given a value as large as the envisioned applications allow.5.3 Two classes

11、of balancing may be considered: balancing in one plane, called static balancing; balancing in two planes, called dynamic balancing.5.4 Static balancing is usually sufficient; dynamic balancing may be necessary for pulleys with a wide-faced rim or those revolving at relatively high speeds.5.5 Pulleys

12、 manufactured for stock shall be statically balanced since their future conditions of use are not known at the time of manufacture.5.6 Static balancing shall be done so as to leave an eccentric residual mass on the working diameter (datum or effective, according to the type of pulley) which does not

13、 exceed the larger of the two following values:a) 0,005 kg;NOTE This value applies only to pulleys where there is adequate material to remove for balancing. Many light-duty pulleys have inadequate space to drill balancing holes or to add appropriate masses by permanent means.b) 0,2 % of the equivale

14、nt mass of the pulley, eventually including any companion bushing.The equivalent mass is taken as the mass of a geometrically identical pulley made of cast iron.5.7 When the rotational frequency, n, in minutes to the power minus one (min-1), of a pulley becomes known, it is advisable to ascertain wh

15、ether dynamic balancing may be necessary, as follows.NOTE The term “rotations per minute (r/min)” is usually used for rotating machines.ISO 254:2011(E)2 ISO 2011 All rights reservedBS ISO 254:2011Determine the limiting speed n1(min-1) by reference to Figure 1 or by calculation using the formula:nld1

16、=1,58 1011(1)wherel is the pulley rim face width, in millimetres;d is the diameter (datum or effective) of the pulley, in millimetres.Then:if n n1: dynamic balancing may be necessary.5.8 For dynamic balancing, the operation shall be implemented in accordance with ISO 1940-1. The balance quality grad

17、e G is determined by the largest of the following two numbers:G1= 6,3 mm/s (2)GvM25= mm/s (3)The expression for G2is derived from the definition in ISO 1940-1.In Formula (3):5 is the practical limit of the residual eccentric mass, in grams, specified in 5.6 a);v is the circumferential pulley speed,

18、in metres per second;M is the equivalent mass of the pulley, in kilograms, as given in 5.6 b).The G quality grade may be less than G1or G2if the user specifies a particular requirement.ISO 254:2011(E) ISO 2011 All rights reserved 3BS ISO 254:2011Figure 1 Limit n1(min-1) for static or dynamic balanci

19、ngISO 254:2011(E)4 ISO 2011 All rights reservedBS ISO 254:2011BS ISO 254:2011ISO 254:2011(E) ISO 2011 All rights reservedICS 21.220.10Price based on 4 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related pub

20、lications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fa

21、x +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy

22、or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresth

23、at subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international a

24、nd foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwi

25、se requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all

26、its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. T

27、el: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, o

28、f the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior

29、written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: