BS ISO 26623-1-2014 Polygonal taper interface with flange contact surface Dimensions and designation of shanks《法兰连接表面的多边锥形接口 柄的尺寸和标注》.pdf

1、BSI Standards PublicationBS ISO 26623-1:2014Polygonal taper interface withflange contact surfacePart 1: Dimensions and designation ofshanksBS ISO 26623-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 26623-1:2014.It supersedes BS ISO 26623-1:2008 which i

2、s withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necess

3、aryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 81564 5ICS 25.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was pu

4、blished under the authority of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 26623-1:2014 ISO 2014Polygonal taper interface with flange contact surface Part 1: Dimensions and designation of shanksInterfaces cne polygonal avec

5、 face dappui Partie 1: Dimensions et dsignation des queuesINTERNATIONAL STANDARDISO26623-1Second edition2014-09-01Reference numberISO 26623-1:2014(E)BS ISO 26623-1:2014ISO 26623-1:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specifi

6、ed, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs

7、 member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 26623-1:2014ISO 26623-1:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1

8、Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2 Polygon-shanks . 14 Clamping forces . 85 Designation 8Annex A (informative) Recommendations for use and application . 9Annex B (normative) Polygon shanks for stationary tools .11BS ISO 26623-1:2014ISO 26623-1:2014(E)ForewordISO (the

9、 International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committe

10、e has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechni

11、cal standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in

12、 accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

13、Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute

14、an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee

15、 responsible for this document is ISO/TC 29, Small tools.This second edition cancels and replaces the first edition (ISO 26623-1:2008), which has been technically revised as follows: addition of polygonal shanks of nominal size 100.ISO 26623 consists of the following parts, under the general title P

16、olygonal taper interface with flange contact surface: Part 1: Dimensions and designation of shanks Part 2: Dimensions and designation of receiversiv ISO 2014 All rights reservedBS ISO 26623-1:2014INTERNATIONAL STANDARD ISO 26623-1:2014(E)Polygonal taper interface with flange contact surface Part 1:

17、Dimensions and designation of shanks1 ScopeThis part of ISO 26623 specifies dimensions for polygonal taper interfaces with flange contact surface polygon-shanks for automatic and manual tool exchange to be applied on machine tools (e. g. turning machines, drilling machines, milling machines, and tur

18、n/milling centres, as well as grinding machines). A range of shank sizes is specified.These shanks incorporate a grooved flange to enable automatic tool exchange. The clamping can be realized by a circular groove using clamping segments or internal screw threads using centre-bolts.The torque is tran

19、smitted by form lock (polygon).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

20、 document (including any amendments) applies.ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium qualityISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without indivi

21、dual tolerance indicationsISO 2768-2, General tolerances Part 2: Geometrical tolerances for features without individual tolerance indications3 Dimensions3.1 GeneralTolerances for linear dimensions for features without individual tolerance indications shall be of tolerance class “m” in accordance wit

22、h ISO 2768-1 and geometrical tolerances for features without individual tolerance indications shall be of tolerance class “K” in accordance with ISO 2768-2.Tolerances for threads where tolerance is not stated shall be in accordance with ISO 965-2.3.2 Polygon-shanksThe dimensions of polygon-shanks sh

23、all be as specified in Figure 1 and Figure 2 and in Table 1.NOTE Additional dimensions as in use for stationary tools are given in Annex A. Additional recommendations for use and application, (i.e. balancing with a particular design for size 100), are given in Annex B. ISO 2014 All rights reserved 1

24、BS ISO 26623-1:2014ISO 26623-1:2014(E)Surface roughness in micrometresDimensions in millimetres2 ISO 2014 All rights reservedBS ISO 26623-1:2014ISO 26623-1:2014(E) ISO 2014 All rights reserved 3BS ISO 26623-1:2014ISO 26623-1:2014(E)4 ISO 2014 All rights reservedBS ISO 26623-1:2014ISO 26623-1:2014(E)

25、Size 100 polygon shanksaGauge line.kr2or f1as alternative.bPosition of the cutting edge for right hand tools with single cutting edge.lDetail R alternative 1.cGauge ball.mDetail R alternative 2.d0,5 45 or R 0,4.nForm of profile from actual ground curve = +0 0070,(sectioned areas).eThread soft.oTheor

26、etical polygon curve.fData chip hole, optional.pActual ground curve.g0,3 45 or R 0,3.qPolygon curve according to Figure 2.hGauge pin.rSection A-A with data chip hole, optional.sRounded.xX-axis for theoretical polygon curve according to Figure 2.Figure 1 Polygon shanks ISO 2014 All rights reserved 5B

27、S ISO 26623-1:2014ISO 26623-1:2014(E)() () 4cos2cos2cos2 += eeDxm() () 4sin2sin2sin2 += eeDymaNormal to polygon curve.Figure 2 Polygon curveTable 1 Polygon shanks DimensionsDimensions in millimetresNominal size 32 40 50 63 80 80X 100b1 0,1 39 46 59,3 70,7 86 110 110b228,3 35,3 44,4 55,8 71,1 88,7 88

28、,7b3 0,1 27,9 34,9 44 55,4 70,7 88,3 88,3b44,2 5,2 6,5 8,5 9,6 9,6 12,4b54,5 5,5 7 9 10,1 10,1 13,2b62,5 2,5 3,5 3,5 3,5 5 5b72,6 2,6 4,1 4,1 4,1 6,1 6,1b81,5 1,5 2 2 2 2 2d1 0,1 32 40 50 63 80 100 100d2+00501,15 18 21 28 32 32 43d3 0,05 16,5 20 24 32 38 38 50,5d4M12 1,5 M14 1,5 M16 1,5 M20 2 M20 2

29、M20 2 M24 2d5 0,1 3,6 4,6 6,1 8,1 9,1 9,1 12NOTEFor dimensions d12and l17, see Annex A.aValid only if balancing is needed.bFor stationary tools, dimensions see Annex B.6 ISO 2014 All rights reservedBS ISO 26623-1:2014ISO 26623-1:2014(E)Nominal size 32 40 50 63 80 80X 100d6 0,2 12,3 14,3 16,5 20,5 20

30、,5 20,5 25d725,2 31,6 39,1 48,5 60,8 87 79,4d8 0,1 21,6 28 35,5 44,9 57,2 57,2 75,8d9 0,3 4 4 4 4 4 4 4d101,5 2 3 4 6 6 7,5d115 5 7 7 7 10 10d12d13 0,05 31d14H9 26Dm22 28 35 44 55 55 72e 0,7 0,9 1,12 1,4 2 2 2,8f10,3 45 0,3 45 0,5 45 0,5 45 0,5 45 0,5 45 0,5 45h1 0,1 9 11 14 18 h1 0,2 22,2 22,2 29h2

31、 11 14 17,5 22 22ah3002+ ,5,4 5,2 5,1 5 4,9 4,9 4,9l12,5 2,5 3 3 3 3 3l2 0,1 19 24 30 38 48 48 60l3min 15 20 20 22 30 32 36l41 1,5 1,5 1,5 1,5 1,5 2l53,2003+ ,4004+ ,5,3005+ ,6,2005+ ,8005+ ,8005+ ,11005+ ,l6 0,15 6 8 10 12 12 16 16l7 0,15 6 9 10 11 20 20 20l8min 6 6 7 9 0 0 10l99 12 12 12 12 12 16l

32、10 0,2 8 11,5 14 15,5 25 25 26,5l11 0,1 13,5 17,5 22 26 34 34 42,5l122,8 0,15 3,4 0,15 4,6 0,15 5,8 0,15 8,5 0,15 8,5 0,15 11l133,6 3,5 4 6,5 6,5 6,5 8l140,3 0,4 0,5 0,6 0,6 0,6 0,6l15 0,2 2 1,4 1,5 1,6 1,6 1,6 1,9l169 12 12 12 12 12 16l17l18bl19 3,8l20 1,5NOTEFor dimensions d12and l17, see Annex A.

33、aValid only if balancing is needed.bFor stationary tools, dimensions see Annex B.Table 1 (continued) ISO 2014 All rights reserved 7BS ISO 26623-1:2014ISO 26623-1:2014(E)Nominal size 32 40 50 63 80 80X 100l21 9,5r102+3 3 4 5 6 6 7r20,3 0,3 0,5 0,5 0,5 0,5 0,5r3010,0,75 1 1,5 2 3 3 3,75r40,3 0,3 0,3 0

34、,3 0,3 0,3 0,4NOTEFor dimensions d12and l17, see Annex A.aValid only if balancing is needed.bFor stationary tools, dimensions see Annex B.4 Clamping forcesThe clamping system shall provide sufficient clamping force to ensure contact of the shank flange with the face of the receiver. A guide to clamp

35、ing forces for polygon-shank is given in Annex A.5 DesignationA polygon-shank in accordance with this part of ISO 26623 shall be designated by the following:a) “POLYGON-SHANK”;b) reference to this part of ISO 26623 (i.e. ISO 26623-1);c) designation symbols PSC;d) nominal size, in millimetres.EXAMPLE

36、 Designation of a polygon-shank for automatic and manual tool exchange with nominal size 32:POLYGON-SHANK ISO 26623-1 PSC 32Table 1 (continued)8 ISO 2014 All rights reservedBS ISO 26623-1:2014ISO 26623-1:2014(E)Annex A (informative) Recommendations for use and applicationA.1 Clamping forcesVariation

37、s of taper shank and receiver size within the specified limits of tolerance will cause the portion of the clamping force acting on the flange surface to vary. However, the clamping forces given in Table A.1 will ensure that the portion of acting on the flange surface is never less than 80 % of the t

38、otal. The flange contact is decisive for the stiffness of the polygonal taper interface.Table A.1 Clamping forceNominal size, mm 32 40 50 63 80 80X 100Clamping force, kN 15 20 25 30 40 40 60Lower clamping forces can be sufficient when operational loads are low (e.g. cutting forces in finish machinin

39、g). Conversely, higher clamping forces can be required when high operational loads are encountered (e.g. cutting and feed forces in heavy machining).A.2 Information about speeds, torques, bending loads and stiffnessThe manufacturer should provide information regarding permissible speeds, torque tran

40、smitting capacities, bending loads, and stiffness.A.3 Information about material and heat treatmentThe polygonal taper shanks should be heat treated with considerations for strength, hardness, and case depth (if not through hardened). Toughness and wear requirements are to be taken into consideratio

41、n.The coupling could be either through hardened or surface hardened depending on what is suitable for the range of application.A.4 General surface hardness recommendationsTapered polygon, internal clamping groove, and axial contact surface: HRC 42 min. External gripper groove area: HRC 51 min.A.5 Ba

42、lancingIf the polygonal taper shank requires balancing before tools or equipment are assembled on to the shank, it may be balanced with a hole located according to Figure A.1 and Table A.2.NOTE The balancing hole is exclusively used for compensation of coolant hole and orientation recess on the poly

43、gonal taper (balanced by design). The data chip hole has not been taken into consideration.If post assembly balancing is needed, it should be confined to the preferred balancing zone as shown in Figure A.1 and Table A.2. ISO 2014 All rights reserved 9BS ISO 26623-1:2014ISO 26623-1:2014(E)aPreferred

44、balancing zone.bPre-balancing hole.Figure A.1 BalancingTable A.2 Dimensions for balancingDimensions in millimetresNominal size 32 40 50 63 80 80X 100d12max recom-mended6,5 7,5 8,5 10 11,5 11,5 14l177 8 10 12 12 12 16h2 29,710 ISO 2014 All rights reservedBS ISO 26623-1:2014ISO 26623-1:2014(E)Annex B

45、(normative) Polygon shanks for stationary toolsB.1 Polygon shanks Design for stationary toolsSee Figure B.1.Figure B.1 Polygon shanks for stationary toolsB.2 Polygon shanks Dimensions for stationary toolsSee Table B.1.Table B.1 Dimensions for stationary toolsDimensions in millimetresNominal size 32

46、40 50 63 80 80X 100l18min 12 16 16 18 20 25 36 ISO 2014 All rights reserved 11BS ISO 26623-1:2014ISO 26623-1:2014(E) ISO 2014 All rights reservedICS 25.060.20Price based on 11 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standar

47、ds-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring togethe

48、r business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizat

49、ions of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and do