BS ISO 2982-2-2013 Rolling bearings Accessories Dimensions for locknuts and locking devices《滚动轴承 附件 防松螺母和锁紧装置的尺寸规格》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 2982-2:2013Rolling bearings AccessoriesPart 2: Dimensions for locknuts and lockingdevicesBS ISO 2982-2:2013 BRITISH STANDARDNational forewordThis British Standard is the U

2、K implementation of ISO 2982-2:2013. Itsupersedes BS ISO 2982-2:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/7, Rolling bearings.A list of organizations represented on this committee can beobtained on request to its secretary.This publicatio

3、n does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 78233 6ICS 21.100.20Compliance with a British Standard cannot confer immunity fromle

4、gal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 2982-2:2013 ISO 2013Rolling bearings Accessories Part 2: Dimensions for locknuts and locking devicesRoulem

5、ents Accessoires Partie 2: Dimensions des crous encoches et dispositifs de blocageINTERNATIONAL STANDARDISO2982-2Third edition2013-04-15Reference numberISO 2982-2:2013(E)BS ISO 2982-2:2013ISO 2982-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unles

6、s otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the ad

7、dress below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 2982-2:2013ISO 2982-2:2013(E) ISO 2013 All rights reserved iiiContents

8、PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 14.1 General . 14.2 Locknuts with 4 slots . 24.3 Lockwashers with straight inner tab . 34.4 Locknuts with 8 slots . 44.5 Locking clip assemblies . 55 Dimensions . 55.1 Locknuts with 4 slots . 55.2 Lockwashers with

9、 straight inner tab . 75.3 Locknuts with 8 slots . 85.4 Locking clip assemblies . 9Annex A (informative) Lockwashers with bent inner tab 11Bibliography .13BS ISO 2982-2:2013ISO 2982-2:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standa

10、rds bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organ

11、izations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in

12、 the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % o

13、f the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 2982-2 was prepared by Technical Committee ISO/TC 4, Rolling be

14、arings.This third edition cancels and replaces the second edition (ISO 2982-2:2001), which has been technically revised.ISO 2982 consists of the following parts, under the general title Rolling bearings Accessories: Part 1: Dimensions for adapter sleeve assemblies and withdrawal sleeves Part 2: Dime

15、nsions for locknuts and locking devicesiv ISO 2013 All rights reservedBS ISO 2982-2:2013INTERNATIONAL STANDARD ISO 2982-2:2013(E)Rolling bearings Accessories Part 2: Dimensions for locknuts and locking devices1 ScopeThis part of ISO 2982 specifies: dimensions of locknuts; runout tolerance of locknut

16、 clamp face with respect to pitch diameter of screw thread; dimensions of lockwashers with straight inner tab for use with 4-slot locknuts; dimensions of locking clip assemblies for use with 8-slot locknuts.The locknuts are also suitable for axial location of bearing inner rings on shafts and for di

17、smounting of withdrawal sleeves.For adapter sleeve assemblies and withdrawal sleeves, see ISO 2982-1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

18、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5593, Rolling bearings VocabularyISO 15241, Rolling bearings Symbols for physical quantities3 Terms and definitionsFor the purposes of this document, the terms and definitions given

19、 in ISO 5593 and the following apply.3.1locking clippart in C-shape for securing a locknut3.2locking clip assemblyassembly comprising a locking clip and a bolt4 Symbols4.1 GeneralFor the purposes of this document, the symbols given in ISO 15241 and the following listed in 4.2, 4.3, 4.4 and 4.5 apply

20、.The symbols shown in Figure 1, Figure 2, Figure 3 and Figure 4 and the values given in Table 1, Table 2, Table 3 and Table 4 denote nominal dimensions, unless specified otherwise. ISO 2013 All rights reserved 1BS ISO 2982-2:2013ISO 2982-2:2013(E)4.2 Locknuts with 4 slotsSee Figure 1.B locknut width

21、b width of slot in locknutd1outside diameter of clamp face of locknutd2outside diameter of locknutG designation of screw threadh depth of slot in locknuttSrunout tolerance of locknut clamp face with respect to pitch diameter of screw threadFigure 1 Locknut with 4 slots2 ISO 2013 All rights reservedB

22、S ISO 2982-2:2013ISO 2982-2:2013(E)4.3 Lockwashers with straight inner tabSee Figure 2.B7material thickness of lockwasherd3bore diameter of lockwasherd4root diameter of outer tab of lockwasherd5outside diameter of lockwasherf width of outer tab of lockwasherf1width of inner tab of lockwasherM distan

23、ce between inner tab and bore (d3 height of inner tab)N minimum number of outer tabs of lockwasherFigure 2 Lockwasher with straight inner tab ISO 2013 All rights reserved 3BS ISO 2982-2:2013ISO 2982-2:2013(E)4.4 Locknuts with 8 slotsSee Figure 3.B locknut widthb width of slot in locknutd1outside dia

24、meter of clamp face of locknutd2outside diameter of locknutG1designation of screw thread of the locknut boreh depth of slot in locknuttSrunout tolerance of locknut clamp face with respect to pitch diameter of screw threadFigure 3 Locknut with 8 slots4 ISO 2013 All rights reservedBS ISO 2982-2:2013IS

25、O 2982-2:2013(E)4.5 Locking clip assembliesSee Figure 4 for bolt and locking clip.b1width of locking clipd6diameter of hole in locking clipe inner width of locking clipG2designation of screw threadh1height of locking clipl length of bolts material thickness of locking clipNOTE The bolt may or may no

26、t be secured to prevent loosening.Figure 4 Locking clip assembly5 Dimensions5.1 Locknuts with 4 slotsDimensions and runout tolerance, tS, of locknuts with 4 slots are given in Table 1. ISO 2013 All rights reserved 5BS ISO 2982-2:2013ISO 2982-2:2013(E)Table 1 Locknuts with 4 slotsDimensions and toler

27、ances in millimetresGad2d1B b htSbM10 0,75 M12 1 M15 1 M17 1 M20 118 22 25 28 3213,5 17 21 24 264 4 5 5 63 3 4 4 42 2 2 2 20,04 0,04 0,04 0,04 0,04M25 1,5 M30 1,5 M35 1,5 M40 1,5 M45 1,538 45 52 58 6532 38 44 50 567 7 8 9 105 5 5 6 62 2 2 2,5 2,50,04 0,04 0,04 0,04 0,04M50 1,5 M55 2 M60 2 M65 2 M70

28、270 75 80 85 9261 67 73 79 8511 11 11 12 126 7 7 7 82,5 3 3 3 3,50,04 0,05 0,05 0,05 0,05M75 2 M80 2 M85 2 M90 2 M95 298 105 110 120 12590 95 102 108 11313 15 16 16 178 8 8 10 103,5 3,5 3,5 4 40,05 0,05 0,05 0,05 0,05M100 2 M105 2 M110 2 M115 2 M120 2130 140 145 150 145120 126 133 137 13518 18 19 19

29、 2010 12 12 12 124 5 5 5 50,05 0,05 0,05 0,05 0,05M120 2 M125 2 M130 2 M130 2 M135 2155 160 155 165 175138 148 145 149 16020 21 21 21 2212 12 12 12 145 5 5 5 60,05 0,06 0,06 0,06 0,06M140 2 M140 2 M145 2 M150 2 M150 2165 180 190 180 195155 160 171 170 17122 22 24 24 2412 14 14 14 145 6 6 5 60,06 0,0

30、6 0,06 0,06 0,06M155 3 M160 3 M160 3 M165 3 M170 3200 190 210 210 200182 180 182 193 19025 25 25 26 2616 14 16 16 167 5 7 7 50,06 0,06 0,06 0,06 0,06M170 3 M180 3 M180 3 M190 3 M190 3220 210 230 220 240193 200 203 210 21426 27 27 28 2816 16 18 16 187 5 8 5 80,06 0,06 0,06 0,06 0,06M200 3 M200 3 Tr21

31、0 4 Tr220 4 Tr230 4240 250 270 280 290222 226 238 250 26029 29 30 32 3418 18 20 20 208 8 10 10 100,06 0,06 0,12 0,12 0,12Tr240 4 Tr250 4 Tr260 4 Tr280 4300 320 330 350270 290 300 32034 36 36 3820 20 24 2410 10 12 120,12 0,12 0,12 0,12aTolerance class 5H, ISO 965-3, for metric threads and 7H, ISO 290

32、1, for metric trapezoidal threads.bMeasurements taken at a radius = (thread outside diameter + d1) / 4.6 ISO 2013 All rights reservedBS ISO 2982-2:2013ISO 2982-2:2013(E)5.2 Lockwashers with straight inner tabDimensions of lockwashers with straight inner tab are given in Table 2.Table 2 Lockwashers w

33、ith straight inner tabDimensions in millimetresd3d4d5f1max.Mf aB7bNc10 12 15 17 2013,5 17 21 24 2621 25 28 32 363 3 4 4 48,5 10,5 13,5 15,5 18,53 3 4 4 41 1 1 1 19 11 11 11 1125 30 35 40 4532 38 44 50 5642 49 57 62 695 5 6 6 623 27,5 32,5 37,5 42,55 5 5 6 61,25 1,25 1,25 1,25 1,2513 13 13 13 1350 55

34、 60 65 7061 67 73 79 8574 81 86 92 986 8 8 8 847,5 52,5 57,5 62,5 66,56 7 7 7 81,25 1,5 1,5 1,5 1,513 17 17 17 1775 80 85 90 9590 95 102 108 113104 112 119 126 1338 10 10 10 1071,5 76,5 81,5 86,5 91,58 8 8 10 101,5 1,8 1,8 1,8 1,817 17 17 17 17100 105 110 115 120120 126 133 137 135142 145 154 159 15

35、112 12 12 12 1496,5 100,5 105,5 110,5 11510 12 12 12 121,8 1,8 1,8 2 217 17 17 17 17120 125 130 130 135138 148 145 149 160164 170 161 175 18514 14 14 14 14115 120 125 125 13012 12 12 12 142 2 2 2 217 17 17 17 17140 140 145 150 150155 160 171 170 171171 192 202 188 20516 16 16 16 16135 135 140 145 14

36、512 14 14 14 142 2 2 2 217 17 17 17 17155 160 160 165 170182 180 182 193 190212 199 217 222 21116 18 18 18 18147,5 154 154 157,5 16416 14 16 16 162,5 2,5 2,5 2,5 2,519 19 19 19 19170 180 180 190 190193 200 203 210 214232 221 242 231 25218 20 20 20 20164 174 174 184 18416 16 18 16 182,5 2,5 2,5 2,5 2

37、,519 19 19 19 19 ISO 2013 All rights reserved 7BS ISO 2982-2:2013ISO 2982-2:2013(E)d3d4d5f1max.Mf aB7bNc200 200 210 220 230222 226 250 248 262 292 20 20 24 194 194 213 18 18 20 2,5 2,5 3 19 19 19 19 19240 250 260 280270 300 320312 342 36224 28 28233 253 27320 24 243 3 319 19 19 19af shall be b (see

38、Figure 1 and Table 1).bThe thickness is only approximate and small variations are permissible.cSince the locknut has 4 slots, N shall be an odd number.5.3 Locknuts with 8 slotsDimensions and runout tolerance, tS, of locknuts with 8 slots are given in Table 3.Table 3 Locknuts with 8 slotsDimensions a

39、nd tolerances in millimetresG1ad2d1B b htSbSuitable locking clip No.Tr220 4 Tr240 4 Tr260 4 Tr280 4 Tr300 4260 290 310 330 360242 270 290 310 33630 34 34 38 4220 20 20 24 249 10 10 10 120,12 0,12 0,12 0,12 0,121 2 2 3 4Tr300 4 Tr320 5 Tr320 5 Tr340 5 Tr340 5380 380 400 400 440340 356 360 376 40040 4

40、2 42 45 5524 24 24 24 2812 12 12 12 150,12 0,12 0,12 0,12 0,125 6 7 6 8Tr360 5 Tr360 5 Tr380 5 Tr380 5 Tr400 5420 460 450 490 470394 420 422 440 44245 58 48 60 5228 28 28 32 2813 15 14 18 140,12 0,12 0,12 0,12 0,129 8 10 11 10Tr400 5 Tr420 5 Tr420 5 Tr440 5 Tr440 5520 490 540 520 560460 462 490 490

41、51062 52 70 60 7032 32 32 32 3618 14 18 15 200,12 0,15 0,15 0,15 0,1512 13 12 14 15Tr460 5 Tr460 5 Tr480 5 Tr480 5 Tr500 5540 580 560 620 580510 540 530 560 55060 75 60 75 6832 36 36 36 3615 20 15 20 150,15 0,15 0,15 0,15 0,1514 15 16 17 16Tr500 5 Tr530 6 Tr530 6 Tr560 6 Tr560 6630 630 670 650 71058

42、0 590 610 610 65080 68 80 75 8540 40 40 40 4523 20 23 20 250,15 0,15 0,15 0,15 0,1518 19 20 21 22Table 2 (continued)8 ISO 2013 All rights reservedBS ISO 2982-2:2013ISO 2982-2:2013(E)G1ad2d1B b htSbSuitable locking clip No.Tr600 6 Tr600 6 Tr630 6 Tr630 6 Tr670 6700 750 730 800 780660 690 690 730 7407

43、5 85 75 95 8040 45 45 50 4520 25 20 28 200,15 0,15 0,2 0,2 0,219 22 23 24 25Tr670 6 Tr710 7 Tr710 7 Tr750 7 Tr750 7850 830 900 870 950775 780 825 820 875106 90 106 90 11250 50 55 55 6028 25 30 25 340,2 0,2 0,2 0,2 0,226 27 28 29 30Tr800 7 Tr800 7 Tr850 7 Tr850 7 Tr900 7920 1 000 980 1 060 1 030870 9

44、25 925 975 97590 112 90 118 10055 60 60 70 6025 34 25 38 250,2 0,2 0,2 0,2 0,229 30 31 32 31Tr900 7 Tr950 8 Tr950 8 Tr1000 8 Tr1000 81 120 1 080 1 170 1 140 1 2401 030 1 025 1 080 1 085 1 140125 100 125 100 12570 60 70 60 7038 25 38 25 380,2 0,2 0,2 0,2 0,233 34 35 36 37Tr1060 8 Tr1060 8 Tr1120 81 2

45、00 1 300 1 2601 145 1 210 1 205100 125 10060 70 6025 38 250,2 0,2 0,236 37 36aTolerance class 7H, ISO 2901 for metric trapezoidal threads.bMeasurements taken at a radius = (thread outside diameter + d1) / 4.5.4 Locking clip assembliesDimensions of locking clip assemblies are given in Table 4.Table 3

46、 (continued) ISO 2013 All rights reserved 9BS ISO 2982-2:2013ISO 2982-2:2013(E)Table 4 Locking clip assembliesDimensions in millimetresLocking clip No.sab1bh1ed6l cG21 2 3 4 54 4 4 4 420 20 24 24 2412 12 12 12 1213,5 17,5 17,5 20,5 30,57 9 9 9 1212 16 16 16 20M6 M8 M8 M8 M106 7 8 9 105 5 5 5 524 24

47、28 28 2815 15 15 15 1521 31 38 20 249 12 14 9 1216 20 25 16 20M8 M10 M12 M8 M1011 12 13 14 155 5 5 5 532 32 32 32 3615 15 15 15 1540 45 24 28 4314 18 12 14 1825 30 20 25 30M12 M16 M10 M12 M1616 17 18 19 205 5 5 7 736 36 40 40 4015 15 15 21 2128 53 45 34 5114 18 18 18 2225 30 30 30 40M12 M16 M16 M16

48、M2021 22 23 24 257 7 7 7 740 45 45 50 4521 21 21 21 2129 54 34 61 3918 22 18 22 1830 40 30 40 30M16 M20 M16 M20 M1626 27 28 29 307 7 7 7 750 50 55 55 6021 21 21 21 2166 39 69 39 7022 18 26 18 2640 30 50 30 50M20 M16 M24 M16 M2431 32 33 34 357 7 7 7 760 70 70 60 7021 21 21 21 2144 71 76 46 7822 26 26 22 2640 50 50 40 50M20 M24 M24 M20 M2436 377 760 7021 2151 8822 2640 50M20 M24aThe thickness is only approximate and small variations are permissible.bb1shall be b (see Figure 3 and Table 3).cThe lengths shown correspond to preferred length of the bolt for