BS ISO 3019-1-2001 Hydraulic fluid power - Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors - Inch series shown in metric uni.pdf

1、BRITISH STANDARD BS ISO 3019-1:2001 Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 1: Inch series shown in metric units ICS 23.100.99; NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 3019

2、-1:2001 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 BSI 08-2001 ISBN 0 580 38020 3 National foreword This British Standard reproduces verbatim

3、 ISO 3019-1:2001 and implements it as the UK national standard. BS ISO 3019-1: 2001 and BS ISO 3019-2: 2001 supersede BS 6276: 1987 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems and components which has the responsibility

4、 to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “I

5、nternational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance wit

6、h a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internat

7、ional and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 12, a blank page and a back cover. The BSI copyright date displayed in this document indicates when the documen

8、t was last issued. Amendments issued since publication Amd. No. Date CommentsReference number ISO 3019-1:2001(E) INTERNATIONAL STANDARD ISO 3019-1 Second edition 2001-06-01 Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors P

9、art 1: Inch series shown in metric units Transmissions hydrauliques Dimensions et code didentification des flasques de montage et des bouts darbres des pompes volumtriques et moteurs Partie 1: Conversion en units mtriques de la srie en inchesii ISO 3019-1:2001(E)iii Foreword ISO (the International O

10、rganization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been estab

11、lished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardizat

12、ion. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 %

13、 of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 3019 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 3019-1 was prepared by Techn

14、ical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 2, Pumps, motors and integral transmissions. This second edition cancels and replaces the first edition (ISO 3019-1:1975), which has been technically revised. ISO 3019 consists of the following parts, under the general title Hydraulic f

15、luid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors: Part 1: Inch series shown in metric units Part 2: Metric series Annex A forms a normative part of this part of ISO 3019.ISO 3019-1:2001(E) iv Introduction In hydraulic fluid power syst

16、ems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Pumps convert mechanical power into hydraulic fluid power, while motors convert hydraulic fluid power into mechanical power. This part of ISO 3019 provides composite dimension reference and identific

17、ation codes for both pumps and motors, simplified dimensional interchangeability for their flanges and shafts, and preferred sizes and dimensions for new designs.INTERNATIONAL STANDARD ISO 3019-1:2001(E)1 Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of

18、 displacement pumps and motors Part 1: Inch series shown in metric units 1 Scope This part of ISO 3019 specifies sizes and dimensions and establishes an identification code for the two- and four- bolt mounting flanges and the shaft ends of positive-displacement, rotary hydraulic fluid power pumps an

19、d motors. It is applicable to cylindrical keyed shaft ends with an external thread, as well as to those without a thread, to conical keyed shaft ends with an external thread and to 30 involute spline shaft ends. NOTE Involute spline is in accordance with SAE J744 1 . 2 Normative references The follo

20、wing normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 3019. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 3019 ar

21、e encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.

22、 ISO 68-2, ISO general purpose screw threads Basic profile Part 2: Inch screw threads. ISO 1101: 1) , Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out. ISO 5598, Fluid power systems and components Vocabulary. 3 Terms and definitio

23、ns For the purposes of this part of ISO 3019, the terms and definitions given in ISO 5598 apply. 1) To be published. (Revision of ISO 1101:1983) 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E) 2 4 Dimensions 4.1 Tolerances Dimensions shown without tolerances are nominal. Tolerances of form and pos

24、ition are shown in accordance with ISO 1101. 4.2 Selection of mounting flanges and shaft ends Select flange and shaft dimensions for pumps and motors manufactured in accordance with this part of ISO 3019 from Figures 1 to 6 and Tables 1 to 6, inclusive. Shaft ends according to Figure 3 and Figure 6

25、may be provided with a tapped hole. 4.3 Mating components The dimensions and related tolerances of the mating components shall be compatible with the dimensions and tolerances specified in this part of ISO 3019, thus avoiding undue body strain as well as transverse loads on shafts in excess of those

26、 permitted by the pump or motor manufacturer. 5 Identification code 5.1 Mounting flanges Use the mounting flange identification code given in Table 1 and Table 2. The number preceding the hyphen (-) is an approximation, in millimetres, of the mounting flange pilot diameter. The number following the

27、hyphen is the number of mounting bolt holes in the flange. 5.2 Shaft ends Use the shaft end identification codes shown in Tables 3 to 6. The number preceding the hyphen is an approximation, in millimetres, of the shaft major diameter. The number following the hyphen is arbitrarily assigned as follow

28、s: cylindrical keyed shaft ends without thread, -1; cylindrical keyed shaft ends with external thread, -2; conical keyed shaft ends with external thread, -3; 30 involute spline shaft ends, -4. 6 Flange/shaft end combinations Use the preferred flange or shaft end combinations given in Table 7. Use ot

29、her combinations only when necessary, by agreement between the purchaser and the supplier. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E)3 7 Flange/shaft end concentricity and perpendicularity Maintain flange or shaft end concentricity within 0,25 mm and perpendicularity within 0,002/1, in accord

30、ance with Figures 3 to 6. NOTE Rigid couplings may require closer tolerances. 8 Identification statement (Reference to this part of ISO 3019) It is strongly recommended that manufacturers use the following statement in test reports, catalogues and sales literature when electing to comply with this p

31、art of ISO 3019: “Dimensions and identification code for mounting flanges and shaft ends in accordance with ISO 3019-1:2001, Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 1: Inch series shown in metric units.” 1002:

32、19103OSISBBSISO30191:2001 ISO 3019-1:2001(E) 4 Dimensions in millimetres, surface roughness values in micrometres a Slots instead of holes are optional. Figure 1 Basic layout of two-bolt mounting flanges Table 1 Dimensions of two-bolt mounting flanges Dimensions in millimetres Pilot dimensions Flang

33、e dimensions Identification code A 0 0,05 W 0 0,5 X min. Y max. BJKD 0,3 0,1 Tr max. 50-2 50,8 6,4 0,8 64 14 82,6 10,3 102 10 82-2 82,55 6,4 0,8 95 0,5 18 106,4 11,1 130 0,5 12 101-2 101,6 9,7 51 1,5 120 25 146 14,3 174 14 127-2 127 12,7 64 1,5 148 31 181 17,5 213 16 152-2 152,4 12,7 70 1,5 200 1,5

34、40 228,6 20,6 267 1,5 19 165-2 165,1 15,9 70 2,3 270 55 317,5 27 368 25 177-2 177,8 15,9 70 2,3 300 60 350 27 400 25 Tolerances: dimensions without tolerances 0,5. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E)5 Dimensions in millimetres, surface roughness values in micrometres a Slots instead of

35、 holes are optional. Figure 2 Basic layout of four-bolt mounting flanges Table 2 Dimensions of four-bolt mounting flanges Dimensions en millimetres Pilot dimensions Flange dimensions Identification code A 0 0,05 W 0 0,5 X min. Y max. SD 0,3 0,1 r 101-4 101,6 9,7 51 1,5 89,8 14,3 14 127-4 127 12,7 64

36、 1,5 114,5 14,3 14 152-4 152,4 12,7 70 1,5 161,6 20,6 19 165-4 165,1 15,9 70 2,3 224,5 20,6 19 177-4 177,8 15,9 70 2,3 247,5 27 25 Tolerances: dimensions without tolerances 0,5. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E) 6 Dimensions in millimetres, surface roughness values in micrometres Fig

37、ure 3 Basic layout of cylindrical keyed shaft ends without thread Table 3 Dimensions of cylindrical keyed shaft ends without thread Dimensions in millimetres DE (key width) F L L a L S Identification code max. min. 0,03 0 0,13 13-1 12,70 12,67 3,18 14,07 19 16-1 15,88 15,85 3,97 17,6 51 24 19-1 19,0

38、5 19,02 4,78 21,1 51 24 22-1 22,23 22,20 6,35 24,9 63 33 25-1 25,40 25,35 6,35 28,1 70 38 32-1 31,75 31,70 7,94 35,2 76 48 38-1 38,10 38,05 9,53 42,27 83 54 44-1 44,45 44,40 11,11 49,3 92 67 Tolerances: dimensions without tolerances 0,5. a Optional long length shaft. 1002:19103OSISBBSISO30191:2001 I

39、SO 3019-1:2001(E)7 Dimensions in millimetres, surface roughness values in micrometres Figure 4 Basic layout of cylindrical keyed shaft ends with external thread Table 4 Dimensions of cylindrical keyed shaft ends with external thread Dimensions in millimetres CD D T a E (key width) F L C L S L T Iden

40、tification code 0,13 0,08 max. min. 0,03 0 0,13 13-2 2,4 12,70 12,67 3/8-24 3,18 14,07 29 19 14,25 16-2 3,2 15,88 15,85 1/2-20 3,97 17,6 34 24 18,25 19-2 3,2 19,05 19,02 1/2-20 4,78 21,1 34 24 18,25 22-2 4 22,23 22,20 5/8-18 6,35 24,9 48 33 23 25-2 4 25,40 25,35 3/4-16 6,35 28,1 52 38 27 32-2 4 31,7

41、5 31,70 1-12 7,94 35,2 67 48 31 38-2 4 38,10 38,05 1 1/8-12 9,53 42,27 73 54 34,9 44-2 4 44,45 44,40 1 1/4-12 11,11 49,3 89 67 39,7 Tolerances: dimensions without tolerances 0,5. a For threads, see annex A. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E) 8 Dimensions in millimetres, surface roughn

42、ess values in micrometres a Dimension Z is normal to the key and at the large end of the taper. Figure 5 Basic layout of conical keyed shaft ends with external thread Table 5 Dimensions of conical keyed shaft ends with external thread Dimensions in millimetres CD D T a E (key width) L CT L ST L T Z

43、Identification code +0 ,1 3 0,08 max. min. +0 ,0 3 0 min. max. 13-3 2 12,70 12,67 5/16-32 3,18 25 17 12,7 1,63 1,37 16-3 3,2 15,88 15,85 1/2-20 3,97 28 17 18,26 2,13 1,88 19-3 3,2 19,05 19,02 1/2-20 4,78 34 24 18,26 2,54 2,29 22-3 4 22,23 22,20 5/8-18 6,35 43 28 23,01 3,33 3,07 25-3 4 25,43 25,37 3/

44、4-16 6,35 49 35 26,97 3,33 3,07 32-3 4 31,78 31,72 1-12 7,94 49 35 30,96 4,11 3,86 38-3 4 38,13 38,07 1 1/8-12 9,53 62 47 34,92 4,93 4,67 44-3 4 44,48 44,42 1 1/4-12 11,11 71 54 39,67 5,72 5,46 50-3 4 50,83 50,77 1 1/4-12 12,7 90 73 39,67 6,50 6,25 Tolerances: dimensions without tolerances 0,5. a Fo

45、r threads, see annex A. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E)9 Dimensions in millimetres a Spline b Undercut defined by dimension U is optional. Figure 6 Basic layout of 30 involute spline shaft ends Table 6 Dimensions of 30 involute spline shaft ends Dimensions in millimetres Spline L A

46、 min. L B L S U min. Identification code 1st choice 2nd choice 1st choice 2nd choice 1st choice 2nd choice 13-4 9T 20/40 DP 5,1 1,5 19 8,8 16-4 9T 16/32 DP 7,6 1,5 24 11,4 19-4 11T 16/32 DP 8,9 1,5 30 14,3 22-4 13T 16/32 DP 10,2 1,5 33 17,5 25-4 15T 16/32 DP 12,7 1,5 38 20,6 32-4 14T 12/24 DP 15,2 2

47、 48 25,6 35-4 21T 16/32 DP 15,2 24 8 30 38-4 17T 12/24 DP 23T 16/32 DP 17,8 2 2 54 31,9 33,2 44-4 13T 8/16 DP 27T 16/32 DP 20,3 3 2 67 35,8 39,5 50-4 15T 8/16 DP 30T 16/32 DP 25,4 3 2 80 42,1 44,3 Tolerances: dimensions without tolerance 0,5. 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E) 10 Tabl

48、e 7 Flange/shaft combinations Flange series Shaft end series 50- 13- 82- 16- 82- 19- 101- 22- 101- 25- 127- 32- 127- 35- 127- 38- 152- 44- 165- 44- 177- 50- 1002:19103OSISBBSISO30191:2001 ISO 3019-1:2001(E)11 Annex A (normative) ISO inch screw threads Basic dimensions Table A.1 specifies the basic d

49、imensions in inches, of which the basic profile is specified in ISO 68-2. Table A.1 Basic dimensions Diameter Size Number of threads per inch Major Pitch Minor 5/16 32 0,312 5 0,292 2 0,278 7 3/8 24 0,375 0,347 9 0,329 9 1/2 20 0,5 0,467 5 0,445 9 5/8 18 0,625 0,588 9 0,564 9 3/4 16 0,75 0,709 4 0,682 3 1 12 1 0,945 9 0,909 8 11 /8 12 1,125 1,070 9 1,034