BS ISO 3272-4-1994 Microfilming of technical drawings and other drawing office documents - Microfilming of drawings of special and exceptional elongated sizes《技术图纸和其他办公室图纸文件缩微胶片 专用.pdf

1、BRITISH STANDARD BS ISO 3272-4:1994 Implementation of ISO 3272-4:1994 Microfilming of technical drawings and other drawing office documents Part 4: Microfilming of drawings of special and exceptional elongated sizes UDC 778.14:744BSISO3272-4:1994 This British Standard, having been prepared under the

2、 directionof the Information andDocumentation Standards Policy Committee, was publishedunder the authorityofthe Standards Boardand comes into effect on 15May1994 BSI 04-2000 The following BSI references relate to the work on this standard: Committee reference DOT/16 Draft for comment 91/96068DC ISBN

3、 0 580 23156 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Information and Documentation Standards Policy Committee (DOT/-) to Technical Committee DOT/16, upon which the following bodies were represented: British Computer Society Bri

4、tish Library British Office Technology Manufacturers Alliance British Photographic Association Cranfield Imaging and Document Management User Group Her Majestys Stationery Office KODAK Limited Library Association London Borough of Bromley National Centre for Information Media and Technology (Cimtech

5、) United Kingdom Association for Information and Image Management The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Federation of the Electronics Industry Local Authority Organizations Ministry of Defence Royal Institute of British Architec

6、ts Amendments issued since publication Amd. No. Date CommentsBSISO3272-4:1994 BSI 04-2000 i Contents Page Committees responsible Inside front cover National foreword ii Foreword iii Text of ISO 3272-4 1BSISO3272-4:1994 ii BSI 04-2000 National foreword This British Standard reproduces verbatim ISO327

7、2-4:1994and implements it as the UK national standard. This British Standard is published under the direction of the Information and Documentation Standards Policy Committee whose Technical Committee DOT/16 has the responsibility to: aid enquirers to understand the text; present to the responsible i

8、nternational committee any enquiries on interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. NOTEInternational and European Standards, as well as overseas standards, are available from Customer

9、 Services, Publications, BSI, Linford Wood, Milton Keynes, MK146LE. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immuni

10、ty from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISO title page, pages ii to iv, pages 1 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indic

11、ated in the amendment table on the inside front cover.ISO3272-4:1994(E) ii BSI 04-2000 Contents Page Foreword iii Introduction 1 1 Scope 1 2 Normative references 1 3 Definitions 1 4 Microfilming in one frame 1 5 Microfilming in sections 1 6 Non-standard formats 4 Figure 1 Centring marks and overlap

12、2 Figure 2 Multiple frames for formats of not more than890mm in width and more than1210mm in length 3 Figure 3 Multiple frames for formats of more than890mm but not more than 1210mm in width and more than1210mm in length 3 Figure 4 Multiple frames for formats of more than1210mm in width and length 4

13、ISO3272-4:1994(E) BSI 04-2000 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int

14、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic

15、al Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote. Int

16、ernational Standard ISO3272-4was prepared by Technical Committee ISO/TC171, Micrographics and optical memories for document and image recording, storage and use. ISO3272consists of the following parts, under the general title Microfilming of technical drawings and other drawing office documents: Par

17、t 1: Operating procedures; Part 2: Quality criteria and control of35mm silver gelatin microfilms; Part 3: Aperture card for35mm microfilm; Part 4: Microfilming of drawings of special and exceptional elongated sizes; Part 5: Test procedures for duplicating diazo microfilm images in aperture cards; Pa

18、rt 6: Enlargement from35mm microfilm, quality criteria and control.iv blankISO3272-4:1994(E) BSI 04-2000 1 Introduction Drawing offices produce, in addition to drawings, documents which differ in purpose, form and intention. Easy exchanges of such documentation between organizations should be possib

19、le without ambiguities arising from the use of the information they contain. Microfilming enables the information contained in drawing office documents to be reduced to small dimensions thus facilitating survey, transport, handling and storage. Faithful reconstitution of a microform can only be acco

20、mplished readily if the microform satisfies precise requirements with respect to dimensions and quality. The quality requirements themselves can be fulfilled readily only if the original document complies with standards for the preparation of drawings for microfilming. 1 Scope This part of ISO3272es

21、tablishes general principles for microfilming drawings of special and exceptional elongated sizes specified in ISO5457. It is applicable to sequences of microfilmed multiple frame drawings, reduction ratios and frame overlap. 2 Normative references The following standards contain provisions which, t

22、hrough reference in this text, constitute provisions of this part of ISO 3272. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 3272 are encouraged to investigate the possibility of applying the

23、most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3272-1:1983, Microfilming of technical drawings and other drawing office documents Part 1: Operating procedures. ISO 3272-2:1994, Microfilming of technical

24、 drawings and other drawing office documents Part 2: Quality criteria and control of 35 mm silver gelatin microfilms. ISO 5457:1980, Technical drawings Sizes and layout of drawing sheets. ISO 6196-1:1993, Micrographics Vocabulary Part 01: General terms. ISO 6196-2:1993, Micrographics Vocabulary Part

25、 02: Image positions and methods of recording. ISO 6196-3:1983, Micrographics Vocabulary Part 03: Film processing. ISO 6196-4:1987, Micrographics Vocabulary Part 04: Materials and packaging. ISO 6196-5:1987, Micrographics Vocabulary Part 05: Quality of images, legibility, inspection. ISO 6196-6:1992

26、, Micrographics Vocabulary Part 06: Equipment. 3 Definitions For the purposes of this part of ISO 3272, the definitions given in ISO 6196 apply. 4 Microfilming in one frame When microfilming a drawing smaller than 890 mm 1 210 mm in one frame, it shall be positioned so that the centre of the image i

27、s in the centre of the frame. It shall be recorded using the lowest reduction ratio that will allow the whole image to be accommodated within one frame. 5 Microfilming in sections 5.1 Centring marks When microfilming the drawings described in clause4 or drawings too large to be recorded in one frame

28、, centring marks shall be provided at the midpoint of the longer side of each section. Sequential sections shall overlap by at least 100 mm (see Figure 1). If originals have important information in the overlap area, the overlap shall be larger than 100 mm. The reduction ratio shall be selected from

29、 ISO 3272-1 to maximize the use of the frame area. 5.2 Positioning of the document on the camera table If a document requires rotation when microfilmed in sections, it shall be rotated through 90 in an anticlockwise direction. 5.3 Reduction ratio 1/30 5.3.1 Drawings or individual sheets of multishee

30、t drawings not more than 890 mm in width but more than 1 210 mm in length shall be microfilmed in sections, using multiple frames so that they will appear on the processed microfilm as shown in Figure 2. 5.3.2 Drawings or individual sheets of multisheet drawings more than 890 mm but not more than121

31、0 mm in width and more than 1210 mm in length shall be microfilmed in sections, using multiple frames so that they will appear on the processed microfilm as shown in Figure 3. 5.3.3 Drawings or individual sheets of multisheet drawings that are more than 1210 mm in width and more than 1 210 mm in len

32、gth shall be microfilmed in sections, using multiple frames so that they will appear in the processed microfilm as shown in Figure 4.ISO3272-4:1994(E) 2 BSI 04-2000 5.3.4 When drawings or individual sheets of multi-sheet drawings are microfilmed in sections using multiple frames (see Figure 2 to Fig

33、ure 4), no section shall exceed 890 mm by 1 210 mm in size, and there shall be a minimum of 100 mm overlap between adjacent sections. To utilize a full frame for the final section, the overlap may be greater. 5.4 Reduction ratio 1/15 5.4.1 Drawings or individual sheets of multisheet drawings not mor

34、e than 440 mm in width but more than 600 mm in length shall be microfilmed in sections, using multiple frames so that they will appear on the processed microfilm as shown inFigure 2. 5.4.2 Drawings or individual sheets of multisheet drawings more than 440 mm but not more than 600 mm in width, and no

35、t more than 600 mm in length, shall be microfilmed in sections, using multiple frames so that they will appear on the processed microfilm as shown in Figure 3. Figure 1 Centring marks and overlapISO3272-4:1994(E) BSI 04-2000 3 5.4.3 Drawings or individual sheets of multisheet drawings that are more

36、than 600 mm in width and more than 600 mm in length shall be microfilmed in sections, using multiple frames so that they will appear in the processed microfilm as shown in Figure 4. 5.4.4 When drawings or individual sheets of multisheet drawings are microfilmed in sections using multiple frames (see

37、 Figure 2 to Figure 4), no section shall exceed 440 mm by 600 mm in size, and there shall be a minimum of 100 mm overlap between adjacent sections. To utilize a full frame for the final section, the overlap may be greater. Figure 2 Multiple frames for formats of not more than 890 mm in width and mor

38、e than 1 210 mm in length Figure 3 Multiple frames for formats of more than 890 mm but not more than 1 210 mm in width and more than 1 210 mm in lengthISO3272-4:1994(E) 4 BSI 04-2000 5.5 Identification Each frame of a multiframe series shall be identified by consecutive frame numbers as shown in Fig

39、ure 2 to Figure 4 as well as by the engineering document and sheet number. The first frame of a multiframe series shall be numbered F1 and contain the title block. Succeeding frames shall be numbered F2, F3 etc. Identification characters used in microfilming shall be at least 25 mm in height, shall

40、be white on a dark background and shall be so positioned that they will appear in the lower part of the microfilm frame in an area clear of text. 6 Non-standard formats Other formats shall be treated as the smallest standard size that will accommodate the whole document. Figure 4 Multiple frames for

41、 formats of more than 1 210 mm in width and lengthblankBS ISO 3272-4:1994 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international l

42、evel. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be g

43、rateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service c

44、alled PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international

45、standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical He

46、lp to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substa

47、ntial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international sta

48、ndardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not p

49、reclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.