BS ISO 3338-2-2013 Cylindrical shanks for milling cutters Dimensional characteristics of flatted cylindrical shanks《铣刀直柄 削平直柄的型式和尺寸》.pdf

1、BSI Standards PublicationBS ISO 3338-2:2013Cylindrical shanks for millingcuttersPart 2: Dimensional characteristics of flattedcylindrical shanksBS ISO 3338-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 3338-2:2013. Itsupersedes BS ISO 3338-2:2007 which

2、 is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the nece

3、ssaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 77000 5ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was

4、published under the authority of theStandards Policy and Strategy Committee on 31 August 2013.Amendments issued since publicationDate Text affectedBS ISO 3338-2:2013 ISO 2013Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanksQueues cylindriques do

5、utils fraiser Partie 2: Caractristiques dimensionnelles des queues cylindriques mplatINTERNATIONAL STANDARDISO3338-2Seventh edition2013-08-15Reference numberISO 3338-2:2013(E)BS ISO 3338-2:2013ISO 3338-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved.

6、Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at t

7、he address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 3338-2:2013ISO 3338-2:2013(E) ISO 2013 All rights reserved iiiCont

8、ents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2 WE form Flatted cylindrical shanks with single flat for diameter, d1, of 6 mm to 20 mm 13.3 WE form Flatted cylindrical shanks with double flat for diameter, d1, of 25 mm to 63 mm . 23.4 WN form Flatted cylindr

9、ical shanks with inclined clamping surface . 3Annex A (informative) Relationship between the symbols of this part of ISO 3388 and ISO 13399 (all parts) 5Bibliography 6BS ISO 3338-2:2013ISO 3338-2:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nat

10、ional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna

11、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intend

12、ed for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.o

13、rg/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be i

14、n the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Subcommittee SC 2, Hig

15、h speed steel cutting tools and their attachments.This seventh edition cancels and replaces the sixth edition (ISO 3338-2:2007), of which it constitutes a minor revision. In particular, an annex giving the relationship between the symbols of this part of ISO 3338 and the symbols according to ISO 133

16、99 (all parts) has been added.ISO 3338 consists of the following parts, under the general title Cylindrical shanks for milling cutters: Part 1: Dimensional characteristics of plain cylindrical shanks Part 2: Dimensional characteristics of flatted cylindrical shanks Part3: Dimensional characteristics

17、 of threaded shanksiv ISO 2013 All rights reservedBS ISO 3338-2:2013INTERNATIONAL STANDARD ISO 3338-2:2013(E)Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks1 ScopeThis part of ISO 3338 specifies the dimensions of flatted cylindrical shanks for

18、 milling cutters, of diameters 6 mm to 20 mm for single-flatted shanks, of 25 mm to 63 mm for double-flatted shanks and of 6 mm to 32 mm for shank with inclined clamping surface. In the case of single-flatted shanks, it is applicable to both single-ended cutters and double-ended cutters, as double-f

19、latted shanks cannot admit single-ended cutters.The dimensions of plain cylindrical shanks and threaded shanks are given in ISO 3338-1 and ISO 3338-3, respectively.The two shank types covered by ISO 3338-1 and this part of ISO 3338 have the same dimensional characteristics (diameters and lengths), b

20、ut different tolerances on diameters, namely: h8 for plain cylindrical shanks, commonly used for tools mounted in collets; h6 for flatted cylindrical shanks, intended to be mounted in chucks and secured with a clamping screw, and requiring an accuracy adjustment.2 Normative referencesThe following d

21、ocuments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dime

22、nsions without individual tolerance indications3 Dimensions3.1 GeneralAll dimensions and tolerances are given in millimetres. Tolerances not specified shall be of tolerance class “m” in accordance with ISO 2768-1.3.2 WE form Flatted cylindrical shanks with single flat for diameter, d1, of 6 mm to 20

23、 mmThe dimensions of flatted cylindrical shanks with single flat shall be in accordance with the dimensions shown in Figure 1 and given in Table 1. ISO 2013 All rights reserved 1BS ISO 3338-2:2013ISO 3338-2:2013(E)Figure 1 WE Form Flatted cylindrical shanks with single flat3.3 WE form Flatted cylind

24、rical shanks with double flat for diameter, d1, of 25 mm to 63 mmThe dimensions of flatted cylindrical shanks with double flat shall be in accordance with the dimensions shown in Figure 2 and Table 1.Figure 2 WE form Flatted cylindrical shanks with double flat2 ISO 2013 All rights reservedBS ISO 333

25、8-2:2013ISO 3338-2:2013(E)Table 1 WE form Flatted cylindrical shanks with single or double flatd1h6l102+l210l30005+ ,l401+hh11636 184,2-4,88 5,5 6,610 40 20 7 8,41245 22,5 810,414 12,71648 24 1014,218 16,220 50 25 11 18,225 56 32 12 17 2332 60 3614 193040 70 40 3850 80 4518 2347,863 90 50 60,83.4 WN

26、 form Flatted cylindrical shanks with inclined clamping surfaceThe dimensions of flatted cylindrical shanks with inclined clamping surface shall be in accordance with the dimensions shown in in Figure 3 and Table 2.Figure 3 WN form Flatted cylindrical shanks with inclined clamping surface ISO 2013 A

27、ll rights reserved 3BS ISO 3338-2:2013ISO 3338-2:2013(E)Table 2 WN form Flatted cylindrical shanks with inclined clamping surfaced1h6l102+l2l510hh11h1b1b2r2636 18 254,8 5,4 3,5 4,81,28 6,6 7,2 4,7 6,110 40 20 28 8,4 9,1 5,7 7,31245 22,5 3310,4 11,2 6 8,214 12,7 - - 8,11648 24 3614,2 15 7,6 10,11,618

28、 16,2 - - 10,820 50 25 38 18,2 19,1 8,4 11,525 56 32 44 23 24,1 9,3 13,632 60 36 48 30 31,2 9,9 15,54 ISO 2013 All rights reservedBS ISO 3338-2:2013ISO 3338-2:2013(E)Annex A (informative) Relationship between the symbols of this part of ISO 3388 and ISO 13399 (all parts)For the relationship between

29、the symbols of this part of ISO 3388 and symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship between symbols in this part of ISO 3388 and ISO 13399 (all parts)Symbol in this part of ISO 3338(ISO 3338-2)Reference inthis part ofISO 3338(ISO 3338-2)Property namein theISO 133

30、99 seriesSymbolin theISO 13399seriesReference in the ISO 13399 seriesBSU codeb1Not specified Not specified Not specified Not specifiedb2Not specified Not specified Not specified Not specifiedd1Figure 1,Figure 2 andFigure 3Shank diameter DMM ISO/TS 13399-371CF29862B277h Not specified Not specified No

31、t specified Not specifiedh1Not specified Not specified Not specified Not specifiedl1Figure 1,Figure 2 andFigure 3Shank length LS ISO/TS 13399-371CF298870946l2Not specified Not specified Not specified Not specifiedl3Not specified Not specified Not specified Not specifiedl4Not specified Not specified

32、Not specified Not specifiedr2Not specified Not specified Not specified Not specified ISO 2013 All rights reserved 5BS ISO 3338-2:2013ISO 3338-2:2013(E)Bibliography1 ISO 3338-1, Cylindrical shanks for milling cutters Part 1: Dimensional characteristics of plain cylindrical shanks2 ISO 3338-3, Cylindr

33、ical shanks for milling cutters Part 3: Dimensional characteristics of threaded shanks6 ISO 2013 All rights reservedBS ISO 3338-2:2013BS ISO 3338-2:2013ISO 3338-2:2013(E) ISO 2013 All rights reservedICS 25.100.20Price based on 6 pagesThis page deliberately left blankBSI is the national body responsi

34、ble for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswi

35、ck High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and ref

36、ined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our

37、 website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need intern

38、ational and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to Br

39、itish Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discou

40、nts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find

41、out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available,

42、you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity

43、within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the informat

44、ion used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any for

45、m or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW