BS ISO 3375-2010 Textile glass - Determination of stiffness of rovings《纺织玻璃纤维 粗纱硬挺度的测定》.pdf

1、BS ISO 3375:2009ICS 59.100.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTextile glass Determination ofstiffness of rovingsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010. BSI 20ISBN 978 0

2、580 65164 9Amendments/corrigenda issued since publicationDate CommentsBS ISO 3375:2009National forewordThis British Standard is the UK implementation of ISO 3375:2009.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics and prepr

3、egs.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom

4、 legal obligations.10BS ISO 3375:2009Reference numberISO 3375:2009(E)ISO 2009INTERNATIONAL STANDARD ISO3375Second edition2009-11-15Textile glass Determination of stiffness of rovings Verre textile Dtermination de la rigidit des stratifils BS ISO 3375:2009ISO 3375:2009(E) PDF disclaimer This PDF file

5、 may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the r

6、esponsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-cre

7、ation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2

8、009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the co

9、untry of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 3375:2009ISO 3375:2009(E) ISO 2009 All rights reserved iiiForeword ISO (t

10、he International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical commit

11、tee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotech

12、nical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member

13、 bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying

14、 any or all such patent rights. ISO 3375 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. This second edition cancels and replaces the first edition (ISO 3375:1975), of which it constitutes a minor revision. The main changes are as fol

15、lows: a) the sampling clause has been deleted (the sampling standard referred to in the previous edition, ISO 1886, has been withdrawn without replacement); b) the specimen-conditioning time has been changed from 48 h to a minimum of 6 h. BS ISO 3375:2009BS ISO 3375:2009INTERNATIONAL STANDARD ISO 33

16、75:2009(E) ISO 2009 All rights reserved 1Textile glass Determination of stiffness of rovings 1 Scope This International Standard specifies a method for the determination of the stiffness of textile glass rovings. 2 Normative references The following referenced documents are indispensable for the app

17、lication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 291, Plastics Standard atmospheres for conditioning and testing 3 Principle A test specimen of defined length

18、 is suspended at its centre, and the separation of the two hanging ends of the specimen measured at a standard distance below the point of suspension. 4 Apparatus 4.1 Means for the controlled unwinding of the roving (see Figure 1). 4.2 Roving stiffness tester, consisting of a stainless-steel hook of

19、 circular cross-section and a sliding scale positioned 60 mm below the point of suspension (see Figure 2). 5 Conditioning The roving shall be unpacked and the packages conditioned for at least 6 h in one of the standard laboratory atmospheres specified in ISO 291. 6 Procedure 6.1 Carry out the test

20、in one of the standard atmospheres specified in ISO 291. 6.2 Unwind the roving from the outside of the package as shown in Figure 1, pulling it through the guide eye and round the stainless-steel rollers. 6.3 The speed of unwinding shall be about 100 mm/s, since the roving must be handled carefully,

21、 without too much tension. 6.4 Before taking test specimens from the outer layer of the package, first remove at least 10 m of the roving. Then cut off five test specimens, each (500 5) mm long, with a sharp knife. BS ISO 3375:2009ISO 3375:2009(E) 2 ISO 2009 All rights reserved6.5 Drape one of the t

22、est specimens over the hook, ensuring that an equal length of the test specimen is hanging down on each side, and wait (30 5) s before making any measurements. 6.6 Stand directly in front of the end of the test specimen hanging to the left of the hook (to avoid any parallax error) and align the zero

23、 point of the sliding scale with the centre of the roving. 6.7 Move to stand directly in front of the end of the test specimen hanging on the right of the hook (to avoid any parallax error) and read off the distance, in millimetres, between the centres of the hanging ends of the roving. 6.8 Always t

24、ake the readings at the position where the centres of the draped test specimen intersect the top of the sliding scale, situated 60 mm below the top of the hook. 6.9 Proceed in the same way with the remaining four test specimens. 7 Expression of results Report the arithmetic mean of the five measurem

25、ents, expressed in millimetres, as the stiffness of the roving. 8 Test report The test report shall include the following particulars: a) a reference to this International Standard; b) all details necessary for complete identification of the roving tested; c) the outer diameter of the package from w

26、hich the specimens were taken; d) details of the conditioning and test atmosphere used; e) the individual results and their mean; f) the date of the test. BS ISO 3375:2009ISO 3375:2009(E) ISO 2009 All rights reserved 3Dimensions in millimetres Key 1 roving package 2 ceramic guide eye 3 stainless-ste

27、el rollers, diameter 10 mm Figure 1 Means for the controlled unwinding of the roving Dimensions in millimetres Key 1 stainless-steel hook 2 test specimen 3 sliding scale aStiffness of the roving. Figure 2 Roving stiffness tester BS ISO 3375:2009ISO 3375:2009(E) ICS 59.100.10 Price based on 3 pages I

28、SO 2009 All rights reserved BS ISO 3375:2009This page has been intentionally left blank BS ISO3375:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparin

29、g BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is t

30、he constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover

31、. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddress

32、ed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been publi

33、shed as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichg

34、ive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and ot

35、her benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsis

36、ts in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymean

37、s electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: