BS ISO 3869-2017 Agglomerated cork Expansion joint fillers Specifications packaging and marking《软木瓶塞 膨胀连接填料 规范、包装和标记》.pdf

1、Agglomerated cork Expansion joint fillers Specifications, packaging and markingBS ISO 3869:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Agglomerated cork Expansion joint fillers Specifications, packaging and markingAgglomr compos de lige Matriau pour

2、le remplissage de joints de dilatation Spcifications, emballage et marquageINTERNATIONAL STANDARDISO3869Third edition2017-07Reference numberISO 3869:2017(E)National forewordThis British Standard is the UK implementation of ISO 3869:2017. It supersedes BS ISO 3869:2001, which is withdrawn.The UK part

3、icipation in its preparation was entrusted to Technical Committee PRI/81, Cork.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its corr

4、ect application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 94279 2ICS 91.100.50; 79.100Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy a

5、nd Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 3869:2017 ISO 2017Agglomerated cork Expansion joint fillers Specifications, packaging and markingAgglomr compos de lige Matriau pour le remplissage de joints de dilatatio

6、n Spcifications, emballage et marquageINTERNATIONAL STANDARDISO3869Third edition2017-07Reference numberISO 3869:2017(E)BS ISO 3869:2017ISO 3869:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no par

7、t of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member bo

8、dy in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 3869:2017ISO 3869:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in

9、SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can b

10、e requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 3869:2017(E)Foreword iv1 Scope .12 Normative

11、references 13 Terms and definitions .14 Characteristics 14.1 Types 14.2 Materials . 14.3 Dimensions and tolerances 14.4 Recovery . 24.5 Compression . 24.6 Extrusion 24.7 Expansion in water 24.8 Apparent density . 25 Packaging .26 Marking 2Bibliography 3 ISO 2017 All rights reserved iiiContents PageB

12、S ISO 3869:2017ISO 3869:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes

13、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C

14、ommission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO document

15、s should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl

16、e for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given fo

17、r the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles

18、in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 87, Cork.This third edition cancels and replaces the second edition (ISO 3869:2001), of which 4.3 has been technically revised.iv ISO 2017 All r

19、ights reservedBS ISO 3869:2017ISO 3869:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each memb

20、er body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Ele

21、ctrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types

22、of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be

23、held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is infor

24、mation given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (W

25、TO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 87, Cork.This third edition cancels and replaces the second edition (ISO 3869:2001), of which 4.3 has been technically revised.iv

26、 ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 3869:2017(E)Agglomerated cork Expansion joint fillers Specifications, packaging and marking1 ScopeThis document specifies the characteristics of composition cork intended to be used as expansion joint filler between concrete elements or other

27、construction products.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the reference

28、d document (including any amendments) applies.ISO 633, Cork VocabularyISO 3867, Composition cork Expansion joint fillers Test methods3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 633 apply.ISO and IEC maintain terminological databases for use in sta

29、ndardization at the following addresses: ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp IEC Electropedia: available at h t t p :/ www .electropedia .org/ 4 Characteristics4.1 TypesFor the purposes of this document, composition cork can be designated as being of one of the f

30、ollowing two types: Type II1) cork; Type III1) self-expanding cork.4.2 MaterialsComposition cork intended to be used as expansion joint filler shall consist of sheets or preformed strips formed from composition cork produced with clean granulated cork bonded with non-soluble synthetic resin. Sheets

31、or preformed strips of composition cork for expansion joint fillers shall be of such a nature that they do not deform or break during ordinary handling when exposed to atmospheric conditions.4.3 Dimensions and tolerancesComposition cork shall be tested in accordance with ISO 3867. The sample taken s

32、hall have a surface of approximately 0,2 m2and shall consist of sufficient material to provide at least five test specimens 1) ASTM D 1752a1refers to Type I as “sponge rubber” and Type IV as “recycled PVC”; Types II and III are maintained in this document to harmonize the designations in both standa

33、rds, ASTM and ISO. ISO 2017 All rights reserved 1BS ISO 3869:2017ISO 3869:2017(E)measuring 100 mm 100 mm. The dimensions of the sheets or preformed strips of composition cork, Types II and Type III, shall be agreed between the supplier and the customer.The following tolerances shall be observed on t

34、he declared values of these types of material: on the length: 6 mm; on the width: 3 mm; on the thickness: 1,5 mm.4.4 RecoveryComposition cork shall be tested in accordance with ISO 3867. The recovery shall not be less than 90 % of the thickness before the test.4.5 CompressionComposition cork shall b

35、e tested in accordance with ISO 3867. The compression shall be between 340 kPa and 1 035 kPa.4.6 ExtrusionComposition cork shall be tested in accordance with ISO 3867. The extrusion shall not be greater than 6 mm.4.7 Expansion in waterSelf-expanded cork shall be tested in accordance with ISO 3867. T

36、he increase in thickness shall not be less than 140 % of the thickness before the test.4.8 Apparent densityComposition cork shall be tested in accordance with ISO 3867. The manufacturer shall declare the apparent density.5 PackagingComposition cork intended to be used as expansion joint filler shall

37、 be stored and transported on pallets or other suitable flat surfaces to prevent breakage and permanent deformation due to weather conditions.Self-expanding agglomerated cork shall be wrapped in waterproof paper and sealed, to prevent the entrance of moisture, and packaged in appropriate sizes for h

38、andling on site.6 MarkingPackages shall show the following information: reference to this document, i.e. ISO 3869; the product designation; the manufacturers identification; the source/origin.2 ISO 2017 All rights reservedBS ISO 3869:2017ISO 3869:2017(E)measuring 100 mm 100 mm. The dimensions of the

39、 sheets or preformed strips of composition cork, Types II and Type III, shall be agreed between the supplier and the customer.The following tolerances shall be observed on the declared values of these types of material: on the length: 6 mm; on the width: 3 mm; on the thickness: 1,5 mm.4.4 RecoveryCo

40、mposition cork shall be tested in accordance with ISO 3867. The recovery shall not be less than 90 % of the thickness before the test.4.5 CompressionComposition cork shall be tested in accordance with ISO 3867. The compression shall be between 340 kPa and 1 035 kPa.4.6 ExtrusionComposition cork shal

41、l be tested in accordance with ISO 3867. The extrusion shall not be greater than 6 mm.4.7 Expansion in waterSelf-expanded cork shall be tested in accordance with ISO 3867. The increase in thickness shall not be less than 140 % of the thickness before the test.4.8 Apparent densityComposition cork sha

42、ll be tested in accordance with ISO 3867. The manufacturer shall declare the apparent density.5 PackagingComposition cork intended to be used as expansion joint filler shall be stored and transported on pallets or other suitable flat surfaces to prevent breakage and permanent deformation due to weat

43、her conditions.Self-expanding agglomerated cork shall be wrapped in waterproof paper and sealed, to prevent the entrance of moisture, and packaged in appropriate sizes for handling on site.6 MarkingPackages shall show the following information: reference to this document, i.e. ISO 3869; the product

44、designation; the manufacturers identification; the source/origin.2 ISO 2017 All rights reserved ISO 3869:2017(E)Bibliography1 ASTM D 1752a:2004, Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction ISO 2017 A

45、ll rights reserved 3BS ISO 3869:2017ISO 3869:2017(E) ISO 2017 All rights reservedICS 79.100; 91.100.50Price based on 3 pagesBS ISO 3869:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and

46、services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience

47、and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information

48、 on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, includ

49、ing British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or