BS ISO 4161-2012 Hexagon nuts with flange style 2 Coarse thread《2型六角法兰面螺母 粗牙螺纹》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 4161:2012Hexagon nuts with flange,style 2 Coarse threadBS ISO 4161:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 4161:2012.It

2、 supersedes BS ISO 4161:1999, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee FME/9/1, Fasteners - Mechanical properties.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport

3、 to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012ISBN 978 0 580 78297 8 ICS 21.060.20 Compliance with a British Standard cannot confer immunity from legal obligati

4、ons.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 4161:2012 ISO 2012Hexagon nuts with flange, style 2 Coarse threadcrous hexagonaux embase cylindro-tron

5、conique, style 2 Filetage pas grosINTERNATIONAL STANDARDISO4161Third edition2012-09-01Reference numberISO 4161:2012(E)BS ISO 4161:2012ISO 4161:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwise specified, no part of this publication may b

6、e reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41

7、22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 4161:2012ISO 4161:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Dimensions . 14 Requirements and reference International Standards 45 Designati

8、on . 4Annex A (informative) Gauging of hexagon nuts with flange . 5Bibliography . 7BS ISO 4161:2012ISO 4161:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standard

9、s is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take

10、part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to

11、prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility tha

12、t some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 4161 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with internal metric thread.This third edition

13、cancels and replaces the second edition (ISO 4161:1999), of which it constitutes a minor revision.iv ISO 2012 All rights reservedBS ISO 4161:2012INTERNATIONAL STANDARD ISO 4161:2012(E)Hexagon nuts with flange, style 2 Coarse thread1 ScopeThis International Standard specifies the characteristics of h

14、exagon nuts with flange (style 2), with metric coarse threads from M5 to M20 inclusive, of product grade A for threads up to and including M16 and product grade B for threads above M16.If, in special cases, specifications other than those listed in this International Standard are required, they can

15、be selected from existing International Standards, for example ISO 261, ISO 724, ISO 898-2, ISO 965-2 and ISO 3506-2.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe

16、rences, the latest edition of the referenced document (including any amendments) applies.ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensionsISO 261, ISO general purpose metric screw threads General planISO 898-2, Mechanical properties of fasteners made of carbon s

17、teel and alloy steel Part 2: Nuts with specified property classes Coarse thread and fine pitch threadISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium qualityISO 3269, Fasteners Acceptance inspectionI

18、SO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: NutsISO 4042, Fasteners Electroplated coatingsISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-2, Fasteners Surface discontinuities Part 2: NutsISO 89

19、92, Fasteners General requirements for bolts, screws, studs and nutsISO 10683, Fasteners Non-electrolytically applied zinc flake coatings3 DimensionsSee Figure 1 and Table 1.Symbols and descriptions of dimensions are specified in ISO 225. ISO 2012 All rights reserved 1BS ISO 4161:2012ISO 4161:2012(E

20、)amwis the wrenching height; see note to Table 1.b = 90 to 120.c = 15 to 30.d = 15 to 25.ec is measured at dw,min.fContour of the edge is at the discretion of the manufacturer.Figure 12 ISO 2012 All rights reservedBS ISO 4161:2012ISO 4161:2012(E)Table 1 DimensionsDimensions in millimetresThread DM5

21、M6 M8 M10 M12 (M14)aM16 M20Pb0,8 1 1,25 1,5 1,75 2 2 2,5c min. 1,0 1,1 1,2 1,5 1,8 2,1 2,4 3,0damax. 5,75 6,75 8,75 10,80 13,00 15,10 17,30 21,60min. 5,00 6,00 8,00 10,00 12,00 14,00 16,00 20,00dcmax. 11,8 14,2 17,9 21,8 26,0 29,9 34,5 42,8dwmin. 9,8 12,2 15,8 19,6 23,8 27,6 31,9 39,9e min. 8,79 11,

22、05 14,38 16,64 20,03 23,36 26,75 32,95mmax. 5,00 6,00 8,00 10,00 12,00 14,00 16,00 20,00min. 4,70 5,70 7,64 9,64 11,57 13,30 15,30 18,70mwmin. 2,5 3,1 4,6 5,6 6,8 7,7 8,9 10,7smax. 8,00 10,00 13,00 15,00 18,00 21,00 24,00 30,00min. 7,78 9,78 12,73 14,73 17,73 20,67 23,67 29,16rcmax. 0,3 0,4 0,5 0,6

23、0,7 0,9 1,0 1,2NOTE If the product passes the gauging given in Annex A, the requirements for dimensions e, c and mware satisfied.aThe size in parentheses should be avoided if possible.bP is the pitch of the thread.cRadius, r, applies both at the corners and the flats of the hexagon. ISO 2012 All rig

24、hts reserved 3BS ISO 4161:2012ISO 4161:2012(E)4 Requirements and reference International StandardsSee Table 2.Table 2 Requirements and reference International StandardsMaterial SteelStainless steelGeneral requirements International Standard ISO 8992ThreadTolerance class 6HInternational StandardsISO

25、261, ISO 965-2Mechanical propertiesProperty class 8, 9, 10, 12 A2-70International StandardsISO 898-2 ISO 3506-2ToleranceProduct gradeD M16: AD M16: BInternational Standard ISO 4759-1Finish CoatingAs processed As processedRequirements for electroplating are specified in ISO 4042.Requirements for non-

26、electrolytically applied zinc flake coatings are specified in ISO 10683.Requirements for hot dip galvanization are specified in ISO 10684.Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser.Surface integrityLimits for surface discontinuities a

27、re specified in ISO 6157-2.Acceptability Acceptance inspection is specified in ISO 3269.5 DesignationEXAMPLE A hexagon nut with flange, with thread M12 and of property class 10 is designated as follows:Hexagon nut with flange ISO 4161 - M12 - 104 ISO 2012 All rights reservedBS ISO 4161:2012ISO 4161:

28、2012(E)Annex A (informative) Gauging of hexagon nuts with flangeA.1 Recommended method for gauging of hexagonSee Figure A.1 and Table A.1.The nut shall be gauged using two plain ring gauges, A and B, to demonstrate the coincidental acceptability of hexagon height, wrenching height, corner fill and w

29、idth across corners. Gauge A shall be placed over the nut and shall be seated on the flange. Gauge B shall be placed on the top of the nut normal to the nut axis. The two gauges shall not be in contact.A.2 Recommended method for gauging of flange thicknessSee Figure A.1 and Table A.1.Gauge C is a fl

30、at feeler or ring gauge. It is used to prove that the flange thickness at the junction of the gauge with the hexagon portion is equal to or greater than specified values. The acceptance criterion is that gauge C fits under gauge A without contact where the nut is seated on a flat plate.Key1 gauge A2

31、 gauge B3 gauge CNOTE Wa,min= etheoreticalWb,max= emin 0,01 mmTa,max= mw,minFigure A.1 ISO 2012 All rights reserved 5BS ISO 4161:2012ISO 4161:2012(E)Table A.1Dimensions in millimetresThread Gauge A Gauge B Gauge CD WaTaWbTbWcTcmax. min. max. min. max. min. min. min. max. min.M5 9,25 9,24 2,50 2,49 8

32、,78 8,77 3 14 1,08 1,07M6 11,56 11,55 3,10 3,09 11,04 11,03 4 16 1,19 1,18M8 15,02 15,01 4,60 4,59 14,37 14,36 4 20 1,31 1,30M10 17,33 17,32 5,60 5,59 16,63 16,62 5 24 1,81 1,80M12 20,79 20,78 6,80 6,79 20,02 20,01 5 29 2,20 2,19M14 24,26 24,25 7,70 7,69 23,35 23,34 6 32,5 2,55 2,54M16 27,72 27,71 8

33、,90 8,89 26,74 26,73 6 37 2,96 2,95M20 34,65 34,64 10,70 10,69 32,94 32,93 6 45 3,70 3,696 ISO 2012 All rights reservedBS ISO 4161:2012ISO 4161:2012(E)Bibliography1 ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 2012 All rights reserved 7BS ISO 4161:2012ISO 4161:2012(E) ISO 2

34、012 All rights reservedICS 21.060.20Price based on 7 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the in

35、ternational level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Stan

36、dards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac

37、curacy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Sub

38、scribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly usin

39、g acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the Briti

40、sh Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Sub

41、scribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online acce

42、ss to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI,

43、or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,

44、 stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: