BS ISO 4347-2015 Leaf chains clevises and sheaves Dimensions measuring forces tensile strengths and dynamic strengths《叶片链 u型钩和滑轮 尺寸 测量力 抗拉强度以及动力强度》.pdf

1、BSI Standards PublicationBS ISO 4347:2015Leaf chains, clevises andsheaves Dimensions,measuring forces, tensilestrengths and dynamicstrengthsBS ISO 4347:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 4347:2015. The UK participation in its preparation was e

2、ntrusted to TechnicalCommittee MCE/1, Chains and chain sprockets for power transmission and conveyors.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are r

3、esponsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015ISBN 978 0 580 83413 4 ICS 21.220.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the

4、Standards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 4347:2015 ISO 2015Leaf chains, clevises and sheaves Dimensions, measuring forces, tensile strengths and dynamic strengthsChanes de levage mailles jointives, c

5、hapes et galets de renvoi Dimensions, forces de mesurage, forces de rsistances la traction et forces de rsistances dynamiqueINTERNATIONAL STANDARDISO4347Fifth edition2015-09-01Reference numberISO 4347:2015(E)BS ISO 4347:2015ISO 4347:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT

6、ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permi

7、ssion. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 4347:2015ISO 4347:2

8、015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Chains . 13.1 Nomenclature. 13.2 Chain designation . 33.3 Dimensions . 43.4 Performance Requirements 103.4.1 General. 103.4.2 Minimum tensile strength 103.4.3 Application of tensile force 103.4.4 Dynamic testing .103.5 Pre-loading 1

9、03.6 Length validation . 103.7 Cranked links . 113.8 Marking 114 Clevises 114.1 Types. 114.2 Dimensions 124.3 Minimum tensile strength 154.4 Length adjustment 155 Sheaves 15Annex A (informative) Method of calculating chain minimum dynamic strength .17Annex B (informative) Method of determining maxim

10、um test force Fmaxwhen conducting dynamic strength conformance test 19Bibliography .20 ISO 2015 All rights reserved iiiContents PageBS ISO 4347:2015ISO 4347:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodi

11、es). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

12、non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are desc

13、ribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn t

14、o the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the

15、ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, a

16、s well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is ISO/TC 100, Chains and chain sprockets for power transmission and conveyors.This fifth

17、edition cancels and replaces the fourth edition (ISO 4347:2004), which has been technically revised. This edition specifies the minimum dynamic strength of the chains.iv ISO 2015 All rights reservedBS ISO 4347:2015ISO 4347:2015(E)IntroductionThis International Standard includes two series of chains:

18、 one derived from the ISO 606 A/ASME B29.8 series, designated by the symbol “LH” or “BL”; the other derived from the ISO 606 B series, designated by the symbol “LL”.In Table 1 and Table 2, requirements for minimum dynamic strengths are specified. See informative Annex A for calculation details. ISO

19、2015 All rights reserved vBS ISO 4347:2015BS ISO 4347:2015Leaf chains, clevises and sheaves Dimensions, measuring forces, tensile strengths and dynamic strengths1 ScopeThis International Standard specifies the characteristics of chains used for general lifting purposes, together with the rim profile

20、s of sheaves and the chain attachment ends of clevises. It gives dimensions, limits for interchangeability, length measurement, preloading, minimum tensile strengths and minimum dynamic strengths.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this d

21、ocument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 606, Short-pitch transmission precision roller and bush chains, attachments and associ

22、ated chain sprocketsISO 156541), Fatigue test methods for transmission precision roller chains and leaf chainsASME2)B29.8, Leaf chains, clevises and sheaves3 Chains3.1 NomenclatureThe nomenclature of chains is shown in Figure 1 (which does not necessarily define the actual form of the chain plates)

23、and as given in Table 1 and Table 2.1) To be published (Revision of ISO 15654:2004).2) American Society of Mechanical Engineers.INTERNATIONAL STANDARD ISO 4347:2015(E) ISO 2015 All rights reserved 1BS ISO 4347:2015ISO 4347:2015(E)a) Even lacing2 ISO 2015 All rights reservedBS ISO 4347:2015ISO 4347:2

24、015(E)b) Uneven lacingKey1 inner link2 outer link3 pin4 outer plate5 inner plateFigure 1 Symbols related to Tables 1 and 23.2 Chain designationLeaf chain shall be designated by the prefix “LH” “BL” for chains derived from the ISO 606 A ASME B29.8 series, or by the prefix “LL” for chains derived from

25、 ISO 606 B series, followed by a number of which the first two digits indicate the pitch expressed in sixteenths of an inch and the last two digits indicate the lacing (number of plates in the outer plate pitch and inner plate pitch).To obtain the ASME “BL” reference, the same principle is used, exc

26、ept that the pitch is expressed in eighths of an inch using only one or two digits, dependent on pitch.EXAMPLE 1 A chain with nominal pitch of 12,7 mm derived from chain ISO 08B, consisting of outer plates and inner plates each comprising two plates would be designated byLL 0822EXAMPLE 2 A chain wit

27、h nominal pitch of 19,05 mm derived from ISO 12A ASME chain No. 60, consisting of outer plates comprising three plates and inner plates comprising four plates would be designated byLH 1234 BL 634 ISO 2015 All rights reserved 3BS ISO 4347:2015ISO 4347:2015(E)3.3 DimensionsThe dimensions given in Tabl

28、e 1 and Table 2 provide minimum and maximum limits, ensuring interchangeability and connection to standard design clevises.Manufacturers are responsible for the actual dimensional features of their products.Chains from different manufacturers shall never be placed together within the same applicatio

29、n.4 ISO 2015 All rights reservedBS ISO 4347:2015ISO 4347:2015(E)Table1 Principal chaindimensions, measuring forces, tensile strengths and dynamic strengths, LH seriesISO chain numberASME chainnumberPitchpnom.LacingThickness ofplatesb0max.Hole diameter of innerplatesd1min.Pin diameterd2max.Chainpath

30、depthh1amin.Plate depthh3max.Width over riveted pinb1to b6max.Width between outerplatesl1to l6min.MeasuringforceMinimumtensilestrengthFuMinimumdynamic strength cFdmmmmNkNkNLH 0822 bBL 42212,7222,085,115,0912,3212,0711,14,222222,23,10LH0823BL 42312,7232,085,115,0912,3212,0713,26,322222,23,74LH 0834BL

31、 43412,7342,085,115,0912,3212,0717,410,433433,44,13LH 0844 dBL 44412,7442,085,115,0912,3212,0719,612,444544,54,66LH 0846BL 44612,7462,085,115,0912,3212,0723,816,644544,54,65LH 0866BL 46612,7662,085,115,0912,3212,0728,021,066766,76,21LH 1022 bBL 52215,875222,485,985,9615,3415,0912,94,933433,44,80LH10

32、23BL 52315,875232,485,985,9615,3415,0915,47,433433,45,77LH1034BL 53415,875342,485,985,9615,3415,0920,412,348948,96,39LH 1044 dBL 54415,875442,485,985,9615,3415,0922,814,766766,77,20LH1046BL 54615,875462,485,985,9615,3415,0927,719,566766,77,19LH1066BL 56615,875662,485,985,9615,3415,0932,724,61000100,

33、19,60LH1222bBL 62219,05223,37,967,9418,3418,1117,46,648948,97,05LH1223BL 62319,05233,37,967,9418,3418,1120,89,948948,98,47LH1234BL 63419,05343,37,967,9418,3418,1127,516,575675,69,38LH 1244 dBL 64419,05443,37,967,9418,3418,1130,819,897997,910,6LH1246BL 64619,05463,37,967,9418,3418,1137,526,497997,910

34、,6LH1266BL 66619,05663,37,967,9418,3418,1144,233,21 468146,814,1LH 1622 bBL 82225,4224,099,569,5424,3824,1321,48,284584,512,3LH1623BL 82325,4234,099,569,5424,3824,1325,512,384584,514,8LH1634BL 83425,4344,099,569,5424,3824,1333,820,51 290129,016,3LH 1644 dBL 84425,4444,099,569,5424,3824,1337,924,6169

35、0169,018,4LH1646BL 84625,4464,099,569,5424,3824,1346,232,71690169,018,4LH1666BL 86625,4664,099,569,5424,3824,1354,541,12 536253,624,6 ISO 2015 All rights reserved 5BS ISO 4347:2015ISO 4347:2015(E)ISO chain numberASME chainnumberPitchpnom.LacingThickness ofplatesb0max.Hole diameter of innerplatesd1mi

36、n.Pin diameterd2max.Chainpath depthh1amin.Plate depthh3max.Width over riveted pinb1to b6max.Width between outerplatesl1to l6min.MeasuringforceMinimumtensilestrengthFuMinimumdynamic strength cFdmmmmNkNkNLH 2022 bBL 102231,75224,911,1411,1130,4830,1825,49,81156115,618,8LH2023BL 102331,75234,911,1411,1

37、130,4830,1830,414,81156115,622,6LH2034BL 103431,75344,911,1411,1130,4830,1840,324,51824182,425,0LH 2044 dBL 104431,75444,911,1411,1130,4830,1845,229,52313231,328,2LH2046BL 104631,75464,911,1411,1130,4830,1855,139,42313231,328,2LH2066BL 106631,75664,911,1411,1130,4830,1865,049,23470347,037,6LH 2422 b

38、BL122238,1225,7712,7412,7136,5536,229,711,61512151,226,7LH2423BL 122338,1235,7712,7412,7136,5536,235,517,41512151,232,0LH2434BL 123438,1345,7712,7412,7136,5536,247,128,92 446244,635,4LH 2444 dBL 124438,1445,7712,7412,7136,5536,252,934,43025302,540,0LH2446BL 124638,1465,7712,7412,7136,5536,264,646,33

39、025302,539,9LH2466BL 126638,1665,7712,7412,7136,5536,276,257,94537453,753,3LH 2822 bBL 142244,45226,614,3214,2942,6742,2433,613,21913191,335,4LH2823BL 142344,45236,614,3214,2942,6742,2440,219,71913191,342,6LH 2834BL 143444,45346,614,3214,2942,6742,2453,432,73158315,847,1LH 2844 dBL 144444,45446,614,

40、3214,2942,6742,2460,039,13826382,653,2LH 2846BL 144644,45466,614,3214,2942,6742,2473,252,33826382,653,0LH 2866BL 146644,45666,614,3214,2942,6742,2486,465,55783578,370,9LH 3222bBL 162250,8227,5217,4917,4648,7448,2640.015,02891289,143,4LH3223BL 162350,8237,5217,4917,4648,7448,2646,622,52891289,152,1LH

41、3234BL 163450,8347,5217,4917,4648,7448,2661,837,54 404440,457,7LH 3244 dBL 164450,8447,5217,4917,4648,7448,2669,344,85783578,365,1LH3246BL 164650,8467,5217,4917,4648,7448,2684,559,95783578,365,0LH3266BL 166650,8667,5217,4917,4648,7448,26100,075,08674867,486,8LH 4022 bBL 202263,5229,9123,8423,8160,88

42、60,3351,819,94337433,764,4Table1(continued)6 ISO 2015 All rights reservedBS ISO 4347:2015ISO 4347:2015(E)ISO chain numberASME chainnumberPitchpnom.LacingThickness ofplatesb0max.Hole diameter of innerplatesd1min.Pin diameterd2max.Chainpath depthh1amin.Plate depthh3max.Width over riveted pinb1to b6max

43、.Width between outerplatesl1to l6min.MeasuringforceMinimumtensilestrengthFuMinimumdynamic strength cFdmmmmNkNkNLH4023BL 202363,5239,9123,8423,8160,8860,3361,729,84337433,777,4LH4034BL 203463,5349,9123,8423,8160,8860,3381,749,46 494649,485,7LH 4044 dBL 204463,5449,9123,8423,8160,8860,3391,659,1867486

44、7,496,6LH4046BL 204663,5469,9123,8423,8160,8860,33111,578,98674867,496,4LH 4066BL 206663,5669,9123,8423,8160,8860,33131,499,0130111301,1128,9aChain path depth is the minimum depth of channel through which the assembled chain will pass.bThese chainshave reducedfatigue strengthandwearlife compared wit

45、huneven lacingsof the same pitchandsame minimum tensile strength. Thisshouldbe takeninto account when selecting a chain for a particular application.cDynamicstrengthvaluesarebasedontestspecimeneachof5freepitchesforP50,8mm andeachofthreefreepitchesforP50,8mm. SeeAnnexAformethodofcalculation.dThese ch

46、ains have reduced wear life compared with uneven lacings of the same pitch and same minimum tensile strength. This should be taken into accountwhenselecting a chain for a particular application.Table1(continued) ISO 2015 All rights reserved 7BS ISO 4347:2015ISO 4347:2015(E)Table2 Principal chaindime

47、nsions, measuring forces, tensile strengths and dynamic strengths, LL seriesISO chain numberPitchpnom.LacingThickness ofplatesb0max.Hole diameter of innerplatesd1min.Pin diameterd2max.Chainpath depthh1amin.Plate depthh3max.Width over riveted pinb1to b3max.Width between outerplatesl1to l3min.Measurin

48、gforceMinimumtensilestrengthFuMinimumdynamic strength cFdmmmmNkNkNLL082212,7221,554,464,4511,1810,928,53,1180182,14LL084412,7441,554,464,4511,1810,9214,69,1360363,21LL086612,7661,554,464,4511,1810,9220,715,2540544,28LL102215,875221,655,095,0813,9813,729,33,4220223,01LL104415,875441,655,095,0813,9813

49、,7216,110,1440444,52LL106615,875661,655,095,0813,9813,7222,916,8660666,03LL122219,05221,95,735,7216,3916,1310,73,9290294,13LL124419,05441,95,735,7216,3916,1318,511,6580586,20LL126619,05661,95,735,7216,3916,1326,319,0870878,27LL162225,4223,28,38,2821,3421,0817,26,2600608,36LL164425,4443,28,38,2821,3421,0830,219,4120012012,5LL166625,4663,28,38,2821,3421,0843,231,0180018016,7LL202231,75223,710,2110,1926,6826,4220,17,29509512,0LL204431,75443,710,2110,192