BS ISO 464-2015 Rolling bearings Radial bearings with locating snap ring Dimensions geometrical product specifications (GPS) and tolerance values《滚动轴承 带定位圈的径向轴承 尺寸 几何产品规格 (GPS) 和公差.pdf

1、BSI Standards PublicationBS ISO 464:2015Rolling bearings Radialbearings with locatingsnap ring Dimensions,geometrical productspecifications (GPS) andtolerance valuesBS ISO 464:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 464:2015. Itsupersedes BS ISO 46

2、4:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/7, Rolling bearings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a

3、 contract. Users are responsible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 82722 8ICS 21.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the

4、authority of theStandards Policy and Strategy Committee on 30 November 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 464:2015 ISO 2015Rolling bearings Radial bearings with locating snap ring Dimensions, geometrical product specifications (GPS) and tolerance va

5、luesRoulements Roulements radiaux segment darrt Dimensions, spcification gomtrique des produits (GPS) et valeurs de tolranceINTERNATIONAL STANDARDISO464Third edition2015-11-01Reference numberISO 464:2015(E)BS ISO 464:2015ISO 464:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO

6、2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permissio

7、n. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 464:2015ISO 464:2015(E)

8、Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 15 Snap ring groove and chamfer dimensions and tolerance values . 46 Snap ring dimensions and tolerance values 7Annex A (informative) Snap ring groove and chamfer dimensions and tolerance values for radi

9、al bearings, D 30 mm .10Annex B (informative) Snap rings for radial bearings, D 30 mm 11Annex C (informative) Material of snap ring .12Annex D (informative) Application example .13Annex E (informative) Example of drawing indications of characteristics with specification for a snap ring groove .14Bib

10、liography .15 ISO 2015 All rights reserved iiiContents PageBS ISO 464:2015ISO 464:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out

11、through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO coll

12、aborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

13、al criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the sub

14、ject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trad

15、e name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Tec

16、hnical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 4, Tolerances, tolerance definitions and symbols (including GPS).This third edition cancels and replaces the second edi

17、tion (ISO 464:1995), of which it constitutes a technical revision with the following changes: implementation of Geometrical Product Specifications (GPS); different presentation of the tables.iv ISO 2015 All rights reservedBS ISO 464:2015ISO 464:2015(E)IntroductionThis International Standard is a mac

18、hine element geometry standard as defined in the geometrical product specification (GPS) system as presented in the matrix model of ISO 146387.The fundamental rules of ISO/GPS given in ISO 80153 apply to this International Standard and the default decision rules given in ISO 14253-15apply to the spe

19、cifications made in accordance with this International Standard, unless otherwise indicated.The connection between functional requirements, measuring technique and measuring uncertainty is always intended to be considered. The traditionally used measuring technique is described in ISO 1132-22. For m

20、easurement uncertainty it is intended that ISO 14253-26should be considered.For small radial bearings, when D 30 mm, manufacturing a snap ring groove might distort the raceways. As such, it is recommended to use bearings with a flanged outer ring instead. Information about snap ring grooves and snap

21、 rings for these small bearings can be found in Annexes A and B.Annexes C and D contain informative information on snap ring material and an example of correct application.Annex E contains an example of a real drawing indication of a snap ring groove. ISO 2015 All rights reserved vBS ISO 464:2015BS

22、ISO 464:2015Rolling bearings Radial bearings with locating snap ring Dimensions, geometrical product specifications (GPS) and tolerance values1 ScopeThis International Standard specifies the snap ring groove dimensions and tolerance values, chamfer dimensions on the snap ring groove side of the oute

23、r ring, and the snap ring dimensions and tolerance values for radial bearings in the dimension series 18 and 19 and the diameter series 0, 2, 3, and 4 (except dimension series 00, 82, and 83), as specified in ISO 151.2 Normative referencesThe following documents, in whole or in part, are normatively

24、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 582, Rolling bearings Chamfer dimensions Maximum valuesISO 1101,

25、Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-outISO 5593, Rolling bearings VocabularyISO 14405-1, Geometrical product specifications (GPS) Dimensional tolerancing Part 1: Linear sizesISO 15241, Rolling bearings Symbols for physica

26、l quantities3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 1101, ISO 5593 and ISO 14405-1 apply.4 SymbolsSee Figures 1 to 3 and Table 1.INTERNATIONAL STANDARD ISO 464:2015(E) ISO 2015 All rights reserved 1BS ISO 464:2015ISO 464:2015(E)Figure 1 Snap r

27、inggD2DFigure 2 Mounted snap ringNOTE Regarding UZ, refer to ISO 1101:2012, 10.2.Figure 3 Snap ring groove and chamfer2 ISO 2015 All rights reservedBS ISO 464:2015ISO 464:2015(E)To express that the geometrical product specification (GPS) system is applied, the dimensional and geometrical characteris

28、tics shall be included in the technical product documentation (for example, on the drawing). The dimensional and geometrical specifications associated to them are described in Table 1.A tolerance value associated to a characteristic is symbolized by t followed by the symbol of characteristic, for ex

29、ample tas.In this International Standard, the ISO default specification operator for size is in accordance with ISO 14405-1, i.e. the two-point size is valid.In Tables 2 to 5, A.1, A.2, B.1, and B.2, the symbols U and L are used as follows: U = upper limit deviation L = lower limit deviationAn examp

30、le of a real drawing indication is given in Annex E.Table 1 Symbols for nominal dimensions, characteristics, and specification modifiersSymbol for nominal dimension (size and distance)aSymbol for characteristicaGPS symbol and specification modifierb, cDescriptionda nominal snap ring groove location

31、distanceas position of snap ring groove face at distance “a” with respect to secondary datum B which is constraint by primary datum Ab nominal snap ring groove widthbs deviation of a two-point size of snap ring groove width from its nominal sizeD nominal bearing outside diameterD1nominal snap ring g

32、roove diameterD1s deviation of a two-point size of snap ring groove diameter from its nominal sizeD2nominal outside diameter of snap ring, when mountedD3nominal inside diameter of snap ring, before mountingD3s deviation of a two-point size of inside diameter of snap ring, before mounting, from its n

33、ominal sizee nominal snap ring section heighteALS MGNdeviation of a minimum circumscribed size of snap ring section height, between two opposite lines, in any longitudinal section, which in-cludes the snap ring outside surface axis, from its nominal sizeaSymbols given in ISO 15241 except for the use

34、d format.bSymbols given in ISO 1101 and ISO 14405-1.cSpecification modifier shall not be indicated on a drawing, because two-point size is the default specification modifier for size.dDescription based on ISO 1101 and ISO 14405-1.NOTE The full set of GPS indications can be seen in Figure 3. ISO 2015

35、 All rights reserved 3BS ISO 464:2015ISO 464:2015(E)Symbol for nominal dimension (size and distance)aSymbol for characteristicaGPS symbol and specification modifierb, cDescriptiondf nominal snap ring thicknessf deviation of a two-point size of snap ring thick-ness from its nominal sizeg nominal snap

36、 ring gap when mountedr0nominal fillet radius at the bottom of snap ring groover0s maxmaximum single fillet radius at the bottom of snap ring groover1nominal chamfer dimension of outer ring on snap ring groove sider1s minsmallest single chamfer dimension of outer ring on snap ring groove sideaSymbol

37、s given in ISO 15241 except for the used format.bSymbols given in ISO 1101 and ISO 14405-1.cSpecification modifier shall not be indicated on a drawing, because two-point size is the default specification modifier for size.dDescription based on ISO 1101 and ISO 14405-1.NOTE The full set of GPS indica

38、tions can be seen in Figure 3.5 Snap ring groove and chamfer dimensions and tolerance valuesSnap ring groove and chamfer dimensions and tolerance values for radial bearings in the dimension series 18 and 19 are given in Table 2 and for radial bearings in the diameter series 0, 2, 3, and 4 are given

39、in Table 3.Chamfer dimension, “r1”, applies at the corners indicated in Figure 3 and is specified with “r1s min” in Tables 2 and 3.Table 2 Snap ring groove and chamfer dimensions and tolerance values for radial bearings in the dimension series 18 and 19Dimensions and tolerance values in millimetresD

40、imension series Dimension series18 19 18 19D D1tD1sa tasa tasb tbsr0s maxr1s minaU L U L 30 28,7 0 0,3 - - 1,3 0,15 0,95 +0,25 0 0,25 - 0,332 30,7 0 0,3 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -34 32,7 0 0,3 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -37 35,7 0 0,3 1,3 0,15 1,7 0,15 0,95 +0,25 0 0,25 0,3 0,339 3

41、7,7 0 0,3 - - 1,7 0,15 0,95 +0,25 0 0,25 - 0,340 38,7 0 0,3 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -aThe corresponding maximum chamfer dimensions are given in ISO 582.Table 1 (continued)4 ISO 2015 All rights reservedBS ISO 464:2015ISO 464:2015(E)Dimension series Dimension series18 19 18 19D D1tD1sa tasa

42、 tasb tbsr0s maxr1s minaU L U L 42 40,7 0 0,3 1,3 0,15 1,7 0,15 0,95 +0,25 0 0,25 0,3 0,344 42,7 0 0,3 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -45 43,7 0 0,3 - - 1,7 0,15 0,95 +0,25 0 0,25 - 0,347 45,7 0 0,3 1,3 0,15 1,7 0,15 0,95 +0,25 0 0,25 0,3 0,352 50,7 0 0,3 1,3 0,15 1,7 0,15 0,95 +0,25 0 0,25 0,3

43、0,555 53,7 0 0,3 - - 1,7 0,15 0,95 +0,25 0 0,25 - 0,558 56,7 0 0,3 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -62 60,7 0 0,4 - - 1,7 0,15 0,95 +0,25 0 0,25 - 0,565 63,7 0 0,4 1,3 0,15 - - 0,95 +0,25 0 0,25 0,3 -68 66,7 0 0,4 - - 1,7 0,15 0,95 +0,25 0 0,25 - 0,572 70,7 0 0,4 1,7 0,15 1,7 0,15 0,95 +0,25 0 0,

44、25 0,3 0,578 76,2 0 0,4 1,7 0,15 - - 1,3 +0,3 0 0,4 0,3 -80 77,9 0 0,4 - - 2,1 0,2 1,3 +0,3 0 0,4 - 0,585 82,9 0 0,4 1,7 0,15 2,1 0,2 1,3 +0,3 0 0,4 0,5 0,590 87,9 0 0,4 1,7 0,15 2,1 0,2 1,3 +0,3 0 0,4 0,5 0,595 92,9 0 0,4 1,7 0,15 - - 1,3 +0,3 0 0,4 0,5 -100 97,9 0 0,4 1,7 0,15 2,5 0,2 1,3 +0,3 0 0

45、,4 0,5 0,5105 102,6 0 0,5 - - 2,5 0,2 1,3 +0,3 0 0,4 - 0,5110 107,6 0 0,5 2,1 0,2 2,5 0,2 1,3 +0,3 0 0,4 0,5 0,5115 112,6 0 0,5 2,1 0,2 - - 1,3 +0,3 0 0,4 0,5 -120 117,6 0 0,5 2,1 0,2 3,3 0,2 1,3 +0,3 0 0,4 0,5 0,5125 122,6 0 0,5 2,1 0,2 3,3 0,2 1,3 +0,3 0 0,4 0,5 0,5130 127,6 0 0,5 2,1 0,2 3,3 0,2

46、1,3 +0,3 0 0,4 0,5 0,5140 137,6 0 0,5 2,5 0,2 3,3 0,2 1,9 +0,3 0 0,6 0,5 0,5145 142,6 0 0,5 - - 3,3 0,2 1,9 +0,3 0 0,6 - 0,5150 147,6 0 0,5 2,5 0,2 3,3 0,2 1,9 +0,3 0 0,6 0,5 0,5165 161,8 0 0,5 3,3 0,2 3,7 0,2 1,9 +0,3 0 0,6 0,5 0,5175 171,8 0 0,5 3,3 0,2 - - 1,9 +0,3 0 0,6 0,5 -180 176,8 0 0,5 - -

47、3,7 0,2 1,9 +0,3 0 0,6 - 0,5190 186,8 0 0,5 3,3 0,2 3,7 0,2 1,9 +0,3 0 0,6 0,5 0,5200 196,8 0 0,5 3,3 0,2 - - 1,9 +0,3 0 0,6 0,5 -aThe corresponding maximum chamfer dimensions are given in ISO 582.Table 2 (continued) ISO 2015 All rights reserved 5BS ISO 464:2015ISO 464:2015(E)Table 3 Snap ring groov

48、e and chamfer dimensions and tolerance values for radial bearings in the diameter series 0, 2, 3, and 4Dimensions and tolerance values in millimetresDiameter series Diameter series0 2, 3, and 4 0 2 3 4D D1tD1sa tasa tasb tbsr0s maxr1s minaU L U L 30 28,17 0 0,26 - - 2,06 0,16 1,35 +0,3 0 0,4 - 0,5 0

49、,5 0,532 30,15 0 0,25 2,06 0,16 2,06 0,16 1,35 +0,3 0 0,4 0,3 0,5 - 0,535 33,17 0 0,25 2,06 0,16 2,06 0,16 1,35 +0,3 0 0,4 0,3 0,5 0,5 -37 34,77 0 0,25 - - 2,06 0,16 1,35 +0,3 0 0,4 - - 0,5 0,540 38,1 0 0,25 - - 2,06 0,16 1,35 +0,3 0 0,4 - 0,5 - -42 39,75 0 0,25 2,06 0,16 2,06 0,16 1,35 +0,3 0 0,4 0,5 - 0,5 0,544 41,75 0 0,25 2,06 0,16 - - 1,35 +0,3 0 0,4 0,5 - - -47 44,6 0 0,25 2,06 0,16 2,46 0,15 1