BS ISO 529-2017 Short machine taps and hand taps《机用短丝锥和手用丝锥》.pdf

1、BS ISO 529:2017Short machine taps and handtapsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 529:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 529:2017. It supersedes BS 949-1:1992 which is withdrawn.The UK partic

2、ipation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 90910 8 ICS 25.100.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the

4、authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 529:2017 ISO 2017Short machine taps and hand tapsTarauds courts machine et mainINTERNATIONAL STANDARDISO529Third edition2017-03Reference numberIS

5、O 529:2017(E)BS ISO 529:2017ISO 529:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mec

6、hanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, Sw

7、itzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 529:2017ISO 529:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 ISO metric threads 24.1 Threads up to M25 . 24.1.1 Full-diameter shank taps with plain connecting portion . 24.1.2 Ful

8、l-diameter shank taps with recess 34.1.3 Relieved-shank taps 44.2 Threads above M25 . 54.2.1 Relieved-shank taps for coarse pitch metric thread . 54.2.2 Relieved-shank taps for fine pitch metric thread 65 ISO inch threads, “Unified coarse” (UNC) and “Unified fine” (UNF) series . 85.1 “Unified” serie

9、s threads up to 25,4 mm . 85.1.1 Full-diameter shank taps with plain connecting portion . 85.1.2 Full-diameter shank taps with recess 95.1.3 Relieved-shank taps .105.2 “Unified” series threads above 25,4 mm 115.2.1 Relieved-shank taps for “Unified coarse” series threads .115.2.2 Relieved-shank taps

10、for “Unified fine” series threads 126 Non-recommended inch threads 136.1 “British Standard Whitworth” (BSW) and “British Standard Fine” (BSF) threads .136.1.1 Full-diameter shank taps with recess .136.1.2 Relieved-shank taps .146.2 “British Association” (BA) threads 166.2.1 Full-diameter shank taps

11、with plain connecting portion 166.2.2 Full-diameter shank taps with recess .176.2.3 Relieved-shank taps .18Annex A (normative) Shank diameter, overall length and thread length as a function of range of diameters and pitches 19Annex B (informative) Shank diameters and size of driving squares (Extract

12、 from ISO 237) 22Annex C (informative) Relationship between designations in this document and ISO 13399 series 23Bibliography .26 ISO 2017 All rights reserved iiiContents PageBS ISO 529:2017ISO 529:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of n

13、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter

14、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those inte

15、nded for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www

16、 .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the documen

17、t will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the

18、 meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared

19、by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This third edition cancels and replaces the second edition (ISO 529:1993), of which it constitutes a minor revision with the following changes: added Annex C giving the relationship betw

20、een the symbols of this document and the symbols according to the ISO 13399 series.iv ISO 2017 All rights reservedBS ISO 529:2017INTERNATIONAL STANDARD ISO 529:2017(E)Short machine taps and hand taps1 ScopeThis document specifies the general dimensions of short machine taps and hand taps. These dime

21、nsions, established as functions of the thread diameter and pitch, are the following: length of thread (maximum); overall length; shank diameter and dimensions of driving square; dimensions of the connecting portion between the shank and threaded part.This document is applicable to taps intended for

22、 cutting the following threads:a) ISO metric threads: coarse pitch; fine pitch;b) ISO inch threads: “Unified Coarse” series (UNC) and “Unified Fine” series (UNF);c) Inch threads, non-recommended: “British Standard Whitworth” (BSW) and “British Standard Fine” (BSF); “British Association” (BA).NOTE 1

23、The overall length, thread length and diameters of shank for taps whose thread diameter and pitch are not listed in tables are given in Table A.1.NOTE 2 Annex B gives an abstract from ISO 237 for shank diameters and size of driving squares, for information.NOTE 3 Technical specifications for taps co

24、vered by this document (including marking) are given in ISO 8830.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated refe

25、rences, the latest edition of the referenced document (including any amendments) applies.ISO 237, Rotating tools with parallel shanks Diameters of shanks and sizes of driving squares3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databa

26、ses for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp ISO 2017 All rights reserved 1BS ISO 529:2017ISO 529:2017(E)4 ISO metric threads4.1 Threads up to M254

27、.1.1 Full-diameter shank taps with plain connecting portionDimensions in millimetresDesignation Pitch SquareCoarse pitchFine pitchd nom.Coarse Fined1h9blamax.L h16l3a h11cl20,8M1 M1 0,2 10,250,22,52 4M1,1 M1,1 0,2 1,1 5,5 38,5 10M1,2 M1,2 0,2 1,2 M1,4 M1,4 0,2 1,4 0,3 7 40 12M1,6 M1,6 0,2 1,60,3513M

28、1,8 M1,8 0,2 1,8 8 41M2 M2 0,25 2 0,40,2513,5M2,2 M2,2 0,25 2,20,45 2,8 9,5 44,5 15,5 2,24 5M2,5 M2,5 0,35 2,5 0,35aManufacturers, if they wish, may increase the thread length to lll+32.bIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is

29、h11.cIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position in relation to the shank.2 ISO 2017 All rights reservedBS ISO 529:2017ISO 529:2017(E)4.1.2 Full-diameter shank taps with recessDimensions in millimetresDesignation Pitch

30、SquareCoarse pitchFine pitchd nom.Coarse Fined1h9blamax.L h16d2al3a h11cl20,8M3 M3 0,35 3 0,50,353,15 11 48 2,12 18 2,55M3,5 M3,5 0,3,5 3,5 0,6 3,55 50 2,5 20 2,8M4 M4 0,5 4 0,70,54 13532,8213,156M4,5 M4,5 0,5 4,5 0,75 4,5 3,15 3,55M5 M5 0,5 5 0,8 5 16 58 3,55 25 4 7 M5,5 0,5 5,5 5,6 17 62 4 26 4,5

31、7M6 M6 0,75 61 0,756,319 664,53058M7 M7 0,75 7 7,1 5,3 5,6M8 M8 1 81,251822 726 35 6,3 9M9 M9 1 9 9 7,1 36 7,1 10M10M10 110 1,5 10 24 80 7, 5 39 8 11M10 1,25 1,25aThe recess of full diameter shank taps with recess is optional at the manufacturers discretion. If the recess is not required, such taps

32、shall have a thread length equal to lll+32.bIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.cIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position in relation t

33、o the shank. ISO 2017 All rights reserved 3BS ISO 529:2017ISO 529:2017(E)4.1.3 Relieved-shank tapsDimensions in millimetresDesignation Pitch SquareCoarse pitch Fine pitchd nom.Coarse Fined1h9al max.L h16a h11bl20,8M3 M3 0,35 3 0,50,352,24 11 48 1,84M3,5 M3,5 0,3,5 3,5 0,6 2,5 50 2M4 M4 0,5 4 0,70,53

34、,15 13532,55M4,5 M4,5 0,5 4,5 0,75 3,55 2,8M5 M5 0,5 5 0,8416 583,156 M5,5 0,5 5,5 17 62M6 M6 0,75 61 0,754,519 663,55M7 M7 0,75 7 5,6 4,5 7M8 M8 1 81,2516,322 7258M9 M9 1 9 7,1 5,6M10M10 1101,5 824 806,3 9M10 1,25 1,25M11 11 25 85M12M12 1,2512 1,751,259 29 89 7,1 10M12 1,5 1,5M14M14 1,251421,2511,2

35、 30 95 9 12M14 1,51,5 M15 1,5 15M16 M16 1,5 1612,5 32 102 10 13 M17 1,5 17 M18M18 1,5182,514 37 112 11,2 14M18 2 2M20M20 1,5201,5M20 2 2M22M22 1,5221,516 38 118 12,5 16M22 2 2aIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.bIn acc

36、ordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position in relation to the shank.4 ISO 2017 All rights reservedBS ISO 529:2017ISO 529:2017(E)Designation Pitch SquareCoarse pitch Fine pitchd nom.Coarse Fined1h9al max.L h16a h11bl20,8M24M2

37、4 1,524 31,518 45 130 14 18M24 2 2M25 1,525 1,5M25 2 2aIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.bIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position in

38、 relation to the shank.4.2 Threads above M254.2.1 Relieved-shank taps for coarse pitch metric threadDimensions in millimetresDesignation Pitch Squared nom.d1h9al maxL h16a h11bl21,6M27 27 32045 13516 20M30 303,548 138M33 33 22,4 51 151 18 22M36 36425 57 162 20 24M39 3928 60 170 22,4 26M42 424,5M45 4

39、531,5 67 187 25 28M48 485M52 5235,5 70 200 28 31M56 565,5M60 604076 22131,5 34M64 646 79224M68 68 45 234 35,5 38aIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.bIn accordance with ISO 237, the tolerance is enlarged to h12 when inc

40、luding errors of form of the square and of its position to the shank. ISO 2017 All rights reserved 5BS ISO 529:2017ISO 529:2017(E)4.2.2 Relieved-shank taps for fine pitch metric threadDimensions in millimetresDesignation Pitch Squared nom.d1h9al max.L h16a h11bl21,6M27 1,5271,52037 12716 20M27 2 2M2

41、8 1,5281,5M28 2 2M30 1,5301,5M30 2 2M30 3 3 48 138M32 1,5321,522,437 13718 22M32 2 2M33 1,5331,5M33 2 2M33 3 3 51 151M35 1,5 351,52539 14420 24M36 1,536M36 2 2M36 3 3 57 162M39 1,5391,52839 14922,4 26M39 2 2M39 3 3 60 170M40 1,5401,539 149M40 2 2M40 3 3 60 170M42 1,5421,539 149M42 2 2M42 3 360 170M4

42、2 4 4aIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.bIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position to the shank.6 ISO 2017 All rights reservedBS ISO 5

43、29:2017ISO 529:2017(E)Designation Pitch Squared nom.d1h9al max.L h16a h11bl21,6M45 1,5451,531,545 16525 28M45 2 2M45 3 367 187M45 4 4M48 1,5481,545 165M48 2 2M48 3 367 187M48 4 4M50 1,5501,545 165M50 2 2M50 3 3 67 187M52 1,5521,535,545 17528 31M52 2 2M52 3 370 200M52 4 4M55 1,5551,545 175M55 2 2M55

44、3 370 200M55 4 4M56 1,5561,545 175M56 2 2M56 3 370 200M56 4 4M70 6 70645 79 234 35,5 38M72 6 72M75 6 75M76 6 765083 25840 42M80 6 80M85 6 8586 261M90 6 90M95 6 9556 89 279 45 46M100 6 100aIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is

45、 h11.bIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position to the shank. ISO 2017 All rights reserved 7BS ISO 529:2017ISO 529:2017(E)5 ISO inch threads, “Unified coarse” (UNC) and “Unified fine” (UNF) series5.1 “Unified” series

46、threads up to 25,4 mm5.1.1 Full-diameter shank taps with plain connecting portionDimensions in millimetresDesignation Pitch SquareUNC UNFd nom.UNC UNFd1h9blamax.L h16l3a h11cl20,8 No.080-UNF 1,524 0,3182,5 8 41132 4No.164-UNC No.172-UNF 1,854 0,397 0,353 13,5No.256-UNC No.264-UNF 2,184 0,454 0,3972,

47、8 9,5 44,5 15,5 2,24 5No.348-UNC No.356-UNF 2,515 0,529 0,454aManufacturers, if they wish, may increase the thread length to lll+32.bIn accordance with ISO 237, tolerance h9 applies to precision shanks. For non-precision shanks, the tolerance is h11.cIn accordance with ISO 237, the tolerance is enla

48、rged to h12 when including errors of form of the square and of its position in relation to the shank.8 ISO 2017 All rights reservedBS ISO 529:2017ISO 529:2017(E)5.1.2 Full-diameter shank taps with recessDimensions in millimetresDesignation Pitch SquareUNC UNFd nom.UNC UNFd1h9blamax.L h16d2bmin.l3a h11cl20,8No.440-UNC No.448-UNF 2,8450,6350,5293,15 11 482,1218 2,55No.540-UNC No.544-UNF 3,175 0,577 2,36No.632-UNC No.640-UNF 3,5050,7940,635 3,551350 2,5 20 2,8No.832-UNC No.836-UNF 4,166 0,706 4,5 53 3,15 21 3,55 6No.1024-UNC No.1032-UNF 4,8261,0580,79