BS ISO 5429-2012 Coated abrasives Flap wheels with incorporated flanges or separate flanges《砂布 装有法兰或未装法兰的页轮》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 5429:2012Coated abrasives Flapwheels with incorporatedflanges or separate flangesBS ISO 5429:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implemen

2、tation of ISO 5429:2012. Itsupersedes BS ISO 5429:2005 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/13, Grinding wheels, abrasive tools, paper andcloths, and powders.A list of organizations represented on this committee can beobtained on request

3、to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 70617 2ICS 25.100.70Compliance with a British Standa

4、rd cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2012.Amendments issued since publicationDate Text affectedBS ISO 5429:2012 ISO 2012Coated abrasives Flap wheels with incorporated flanges or

5、 separate flangesAbrasifs appliqus Roues lamelles flasques incorpors ou amoviblesINTERNATIONAL STANDARDISO5429Third edition2012-04-15Reference numberISO 5429:2012(E)BS ISO 5429:2012ISO 5429:2012(E)ii ISO 2012 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2012All rights reserved. Unless otherwi

6、se specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright of

7、ficeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5429:2012ISO 5429:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO m

8、ember bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governm

9、ental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Dire

10、ctives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodi

11、es casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 5429 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC

12、 5, Grinding wheels and abrasives.This third edition cancels and replaces the second edition (ISO 5429:2005), which has been technically revised.Significant changes from ISO 5429:2005 are as follows:a) further dimensions have been included, i.e. in Table 1 additional widths of the flap wheel have be

13、en added;b) Table 1 has been editorially revised to be in line with ISO 3919. ISO 2012 All rights reserved iiiBS ISO 5429:2012BS ISO 5429:2012Coated abrasives Flap wheels with incorporated flanges or separate flanges1 ScopeThis International Standard specifies the nominal dimensions and limit deviat

14、ions of flap wheels with incorporated flanges or separate flanges for use on stationary grinding machines.2 DimensionsSee Figure 1 and Table 1.3 DesignationFlap wheels with incorporated flanges or separate flanges conforming to this International Standard shall be designated bya) “Flap wheel”,b) a r

15、eference to this International Standard, i.e. ISO 5429,c) incorporated flange version A or separate flange version B,d) the diameter of the flap wheel, D, in millimetres,e) the width of the flap wheel, T, in millimetres, andf) the bore diameter, H, for version A, in millimetres.EXAMPLE A flap wheel

16、with incorporated flange A, with diameter D = 350 mm, width T = 75 mm and bore diameter H = 40 mm is designated as follows:Flap wheel ISO 5429 - A 350 75 404 MarkingFlap wheels with incorporated flanges or separate flanges shall be marked with the following information:a) manufacturer, supplier, imp

17、orter or their registered trademark;b) dimensions;c) maximum operating speed;d) maximum permissible speed of rotation;e) grit size.INTERNATIONAL STANDARD ISO 5429:2012(E) ISO 2012 All rights reserved 1BS ISO 5429:2012ISO 5429:2012(E)KeyD diameter of the flap wheelT width of the flap wheelH bore diam

18、eter for version ANOTE The sketch of the flange is given for information only, and does not prejudge the shape or the method of attaching the flange and the flap wheel.Figure 1 Flap wheelTable 1 Dimensions of flap wheelsDimensions in millimetresDT125 30 40 50 75 100100 X X X X 150 X X X X X 165 X X

19、X X X 200 X X X X X 250 X X X X X 300 X X X X X 350 X X X400 X X X500 XHaaDimensions H are left to the manufacturers discretion.2 ISO 2012 All rights reservedBS ISO 5429:2012ISO 5429:2012(E)Bibliography1 ISO 3919, Coated abrasives Flap wheels with shaft ISO 2012 All rights reserved 3BS ISO 5429:2012

20、ISO 5429:2012(E) ISO 2012 All rights reservedICS 25.100.70Price based on 3 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards i

21、n Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fa

22、x +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if

23、anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996

24、7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of s

25、tandards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI

26、 will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8

27、996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information

28、 regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of an

29、d copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extr

30、act may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: