BS ISO 5547-2008 Caseins - Determination of free acidity (Reference method)《酪蛋白 游离酸度的测定(参考方法)》.pdf

1、BRITISH STANDARDBS ISO 5547:2008Caseins Determination of free acidity (Reference method)ICS 67.100.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g5

2、8BS ISO 5547:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 60646 5National forewordThis British Standard is the UK implementation of ISO 5547:2008. It supersedes BS 6248-5:1982 which is withdrawn.

3、 The UK participation in its preparation was entrusted to Technical Committee AW/5, Chemical analysis of milk and milk products.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions

4、of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsReference numbersISO 5547:2008(E)IDF 91:2008(E)INTERNATIONAL STANDARD ISO5547IDF91Second editio

5、n2008-01-15Caseins Determination of free acidity (Reference method) Casines Dtermination de lacidit libre (Mthode de rfrence) BS ISO 5547:2008ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work o

6、f preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmenta

7、l, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main

8、 task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Atte

9、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5547IDF 91 was prepared by Technical Committee ISO/TC 34, Food products, Subcommittee SC 5, Milk and

10、milk products, and the International Dairy Federation (IDF). It is being published jointly by ISO and IDF. This second edition of ISO 5547IDF 91 cancels and replaces the first edition (ISO 5547:1978), of which it constitutes a minor revision. BS ISO 5547:2008iv Foreword IDF (the International Dairy

11、Federation) is a non-profit organization representing the dairy sector worldwide. IDF membership comprises National Committees in every member country as well as regional dairy associations having signed a formal agreement on cooperation with IDF. All members of IDF have the right to be represented

12、at the IDF Standing Committees carrying out the technical work. IDF collaborates with ISO in the development of standard methods of analysis and sampling for milk and milk products. Draft International Standards adopted by the Action Teams and Standing Committees are circulated to the National Commi

13、ttees for voting. Publication as an International Standard requires approval by at least 50 % of the IDF National Committees casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IDF shall not be held responsible for ide

14、ntifying any or all such patent rights. ISO 5547IDF 91 was prepared by the International Dairy Federation (IDF) and Technical Committee ISO/TC 34, Food products, Subcommittee SC 5, Milk and milk products. It is being published jointly by IDF and ISO. All work was carried out by the former Joint ISO-

15、IDF-AOAC Group of Experts (E11-E701) which is now part of the Joint ISO-IDF Action Team on Physical properties and rheological tests, of the Standing Committee on Minor components and characterization of physical properties. This edition of ISO 5547|IDF 91 cancels and replaces IDF 91A:1979, of which

16、 it constitutes a minor revision. BS ISO 5547:20081Caseins Determination of free acidity (Reference method) 1 Scope This International Standard specifies a reference method for the determination of the free acidity of caseins obtained by acid precipitation or lactic fermentation and of rennet casein

17、s. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 385, Laboratory gla

18、ssware Burettes ISO 648, Laboratory glassware Single volume pipettes ISO 835, Laboratory glassware Graduated pipettes ISO 3310-1, Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth ISO 4788, Laboratory glassware Graduated measuring cylinders ISO 5550IDF 78, Casein

19、s and caseinates Determination of moisture content (Reference method) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 free acidity of caseins volume, in millilitres, of a 0,1 mol/l standard volumetric sodium hydroxide solution required to tit

20、rate an aqueous extract of 1 g of the product 4 Principle A test portion at 60 C is extracted using water and filtered. The filtrate is then titrated against a standard volumetric sodium hydroxide solution, using phenolphthalein as indicator. BS ISO 5547:20082 5 Reagents Use only reagents of recogni

21、zed analytical grade, and only distilled or demineralized water or water of equivalent purity, freed from carbon dioxide by boiling for 10 min before use. 5.1 Sodium hydroxide (NaOH), approximately 0,1 mol/l standard volumetric solution. 5.2 Phenolphthalein (C20H14O4), 10 g/l ethanolic solution. 6 A

22、pparatus Usual laboratory apparatus, and in particular the following. 6.1 Analytical balance, capable of weighing to the nearest 0,01 g. 6.2 Conical flask, of capacity 500 ml, with ground neck and fitted with a ground-glass stopper. 6.3 One-mark pipette, of capacity 100 ml, complying with the requir

23、ements of ISO 648, class A. 6.4 Pipette, suitable for measuring 0,5 ml of indicator solution (5.2), complying with the requirements of ISO 648, class A or ISO 835, class A. 6.5 Conical flask, of capacity 250 ml. 6.6 Measuring cylinder, of capacity 250 ml, complying with the requirements of ISO 4788,

24、 class A. 6.7 Burette, graduated in at least 0,1 ml divisions, complying with the requirements of ISO 385, class A. 6.8 Water bath, capable of being maintained at a temperature of (60 2) C. 6.9 Appropriate filter. 6.10 Grinding device, for grinding the laboratory sample, if necessary (see 8.1.4), wi

25、thout development of undue heat and without loss or absorption of moisture. A hammer-mill shall not be used. 6.11 Test sieve, wire cloth, of diameter 200 mm, with nominal size of aperture 500 m, with receiver, complying with ISO 3310-1. 7 Sampling A representative sample should have been sent to the

26、 laboratory. It should not have been damaged or changed during transport or storage. Sampling is not part of the method specified in this International Standard. A recommended sampling method is given in ISO 707|IDF 50 1. 8 Procedure 8.1 Preparation of the test sample 8.1.1 Thoroughly mix the labora

27、tory sample by repeatedly shaking and inverting the container (if necessary, after having transferred all of the laboratory sample to an airtight container of sufficient capacity to allow this operation to be carried out). 8.1.2 Transfer about 50 g of the thoroughly mixed laboratory sample to the te

28、st sieve (6.11). BS ISO 5547:200838.1.3 If the 50 g portion directly passes or almost completely passes the sieve, use for the determination the sample as prepared in 8.1.1. 8.1.4 Otherwise, grind the 50 g portion, using the grinding device (6.10), until it passes the sieve. Immediately transfer all

29、 of the sieved sample to an airtight container of sufficient capacity and mix thoroughly by repeatedly shaking and inverting. During these operations, take precautions to avoid any change in the water content of the product. 8.1.5 After the test sample has been prepared, the determination (8.3) shou

30、ld proceed as soon as possible. Clean the device after grinding each sample. 8.2 Test portion Weigh about 10 g of the test sample (8.1) to the nearest 10 mg and transfer it to the conical flask (6.2). 8.3 Determination Using the 250 ml measuring cylinder (6.6), add 200 ml of freshly boiled water, pr

31、eviously heated to 60 C. Stopper the flask, mix by swirling and place in the water bath at 60 C (6.8) for 30 min. Shake the flask at intervals of about 10 min. Filter, and cool the filtrate to about 20 C. The filtrate must be clear. Transfer 100 ml of the cooled filtrate into the conical flask (6.5)

32、, using the pipette (6.3). Add 0,5 ml of phenolphthalein solution (5.2), using the pipette (6.4). Titrate with sodium hydroxide solution (5.1), until the appearance of a faint pink colour, persisting for at least 30 s. Record the volume used to the nearest 0,01 ml. 9 Expression of results 9.1 Calcul

33、ation 9.1.1 The free acidity of the casein, Vfac, in millilitres, is given by Equation (1) VcVm=NaOHfac20(1) where VNaOHis the volume, in millilitres, of the standard volumetric sodium hydroxide solution (5.1) used; c is the amount of substance concentration, in moles per litre, of the standard volu

34、metric sodium hydroxide solution (5.1); m is the mass, in grams, of the test portion. Calculate the free acidity to the nearest 0,01 ml and report the final result to the nearest 0,1 ml. 9.1.2 To calculate the free acidity of the sample on the dry basis, multiply the result obtained from Equation (1

35、) by Factor (2) ww100100(2) where wwis the water content, as a percentage by mass, of the sample determined according to ISO 5550IDF 78. BS ISO 5547:20084 9.2 Precision 9.2.1 Repeatability The absolute difference between two independent single test results, obtained using the same method on identica

36、l test material in the same laboratory by the same operator using the same equipment within a short interval of time will in not more than 5 % of cases be greater than 0,02 ml of 0,1 mol/l sodium hydroxide solution per 1 g of product. 9.2.2 Reproducibility The absolute difference between two indepen

37、dent single test results, obtained using the same method on identical test material in different laboratories with different operators using different equipment, will in not more than 5 % of cases be greater than 0,04 ml of 0,1 mol/l sodium hydroxide solution per 1 g of product. 10 Test report The t

38、est report shall specify: a) all the information required for the complete identification of the sample; b) the sampling method used, if known; c) the test method used, together with a reference to this International Standard; d) all operating details not specified in this International Standard, or

39、 regarded as optional, together with details of any incident that may have influenced the result(s); e) the test result(s) obtained, and if the repeatability has been checked, the final quoted results obtained. BS ISO 5547:20085Bibliography 1 ISO 707|IDF 50, Milk and milk products Guidance on sampli

40、ng BS ISO 5547:2008BS ISO 5547:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charte

41、r.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy o

42、r ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensure

43、s that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available

44、 from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national

45、, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 70

46、48. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: m

47、embershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of

48、the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior wri

49、tten permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi