BS ISO 5610-1-2014 Tool holders with rectangular shank for indexable inserts General survey correlation and determination of dimensions《数控刀片的矩形柄刀架 尺寸规格的一般检验 相关性以及测定》.pdf

1、BSI Standards PublicationBS ISO 5610-1:2014Tool holders with rectangularshank for indexable insertsPart 1: General survey, correlation anddetermination of dimensionsBS ISO 5610-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-1:2014. Itsupersedes BS

2、ISO 5610-1:2010 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to

3、 include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83609 1ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This

4、British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-1:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determi

5、nation of dimensionsPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 1: Vue densemble, corrlation et dtermination des dimensionsINTERNATIONAL STANDARDISO5610-1Second edition2014-09-01Reference numberISO 5610-1:2014(E)BS ISO 5610-1:2014ISO 5610-1:2014(E)ii ISO 2014 All rights rese

6、rvedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior writte

7、n permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610

8、-1:2014ISO 5610-1:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Survey. 24 Dimensions . 64.1 Cross section and length, l1.64.2 Head length, l264.3 Dimension f .75 Determination of dimensions . 75.1 Cutting edge corner 75.2 Corner radius, r, of t

9、he master indexable inserts .105.3 Length, l1115.4 Dimension f . 115.5 Height, h1.115.6 Tolerances 125.7 Dimension a 125.8 Correction values x and y 12Annex A (informative) Relationship between designations in ISO 5610 (all parts) and ISO/TS 13399-2 and ISO/TS 13399-3 16Bibliography .17BS ISO 5610-1

10、:2014ISO 5610-1:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a

11、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissio

12、n (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should

13、 be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for iden

14、tifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the conven

15、ience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword -

16、 Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition of ISO 5610-1 cancels and replaces the first edition (ISO 5610-1:2010), of which it constitutes a minor revision.ISO

17、 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style

18、K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-1:2014ISO 5610-1:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-1:2014BS ISO 5610-1:2014Tool holders with rectangular shank for indexab

19、le inserts Part 1: General survey, correlation and determination of dimensions1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank for indexable inserts and specifies their styles in relation to their dimensions according to ISO 5610-2, ISO 5610-3, ISO 5610-4, ISO 5610-5, ISO 5

20、610-6, ISO 5610-7, ISO 5610-8, ISO 5610-9, ISO 5610-10, ISO 5610-11, ISO 5610-12, ISO 5610-13, ISO 5610-14, and ISO 5610-15.These tool holders are primarily intended for indexable inserts made of hard metal, ceramic, or other cutting materials intended to be mounted by clamping and used for turning

21、operations. This part of ISO 5610 is general and is intended to be used with ISO 5610-2, ISO 5610-3, ISO 5610-4, ISO 5610-5, ISO 5610-6, ISO 5610-7, ISO 5610-8, ISO 5610-9, ISO 5610-10, ISO 5610-11, ISO 5610-12, ISO 5610-13, ISO 5610-14, and ISO 5610-15.2 Normative referencesThe following documents,

22、 in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3002-1, Basic quantities in

23、cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakersISO 5608, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-2, Tool holders with rectangular shank for indexable i

24、nserts Part 2: Style AISO 5610-3, Tool holders with rectangular shank for indexable inserts Part 3: Style BISO 5610-4, Tool holders with rectangular shank for indexable inserts Part 4: Style DISO 5610-5, Tool holders with rectangular shank for indexable inserts Part 5: Style FISO 5610-6, Tool holder

25、s with rectangular shank for indexable inserts Part 6: Style GISO 5610-7, Tool holders with rectangular shank for indexable inserts Part 7: Style JISO 5610-8, Tool holders with rectangular shank for indexable inserts Part 8: Style KISO 5610-9, Tool holders with rectangular shank for indexable insert

26、s Part 9: Style LISO 5610-10, Tool holders with rectangular shank for indexable inserts Part 10: Style NISO 5610-11, Tool holders with rectangular shank for indexable inserts Part 11: Style RISO 5610-12, Tool holders with rectangular shank for indexable inserts Part 12: Style SISO 5610-13, Tool hold

27、ers with rectangular shank for indexable inserts Part 13: Style TINTERNATIONAL STANDARD ISO 5610-1:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-1:2014ISO 5610-1:2014(E)ISO 5610-14, Tool holders with rectangular shank for indexable inserts Part 14: Style HISO 5610-15, Tool holders with rectangul

28、ar shank for indexable inserts Part 15: Style V3 SurveyThe survey of the tool holders with rectangular shank cross section shall be as given in Table 1. The tool holders with rectangular shank cross section and their corresponding letter symbols and shank sizes shall be in accordance with ISO 5610-2

29、, ISO 5610-3, ISO 5610-4, ISO 5610-5, ISO 5610-6, ISO 5610-7, ISO 5610-8, ISO 5610-9, ISO 5610-10, ISO 5610-11, ISO 5610-12, ISO 5610-13, ISO 5610-14, and ISO 5610-15.The designation code shall be as given in ISO 5608.Table 1 Tool holders with rectangular shanksDimensions in millimetresStyle of tool

30、 holderIllustrationSymbols for the cross sectionh2 bDimensions in0808 1010 1212 1616 2020 2525 3225 3232 4032 4040 5050AISO 5610-2 B ISO 5610-3 D ISO 5610-4 2 ISO 2014 All rights reservedBS ISO 5610-1:2014ISO 5610-1:2014(E)Table 1 (continued)Dimensions in millimetresStyle of tool holderIllustrationS

31、ymbols for the cross sectionh2 bDimensions in0808 1010 1212 1616 2020 2525 3225 3232 4032 4040 5050F ISO 5610-5 G ISO 5610-6 H ISO 5610-14 ISO 2014 All rights reserved 3BS ISO 5610-1:2014ISO 5610-1:2014(E)Table 1 (continued)Dimensions in millimetresStyle of tool holderIllustrationSymbols for the cro

32、ss sectionh2 bDimensions in0808 1010 1212 1616 2020 2525 3225 3232 4032 4040 5050J ISO 5610-7 K ISO 5610-8 L ISO 5610-9 4 ISO 2014 All rights reservedBS ISO 5610-1:2014ISO 5610-1:2014(E)Table 1 (continued)Dimensions in millimetresStyle of tool holderIllustrationSymbols for the cross sectionh2 bDimen

33、sions in0808 1010 1212 1616 2020 2525 3225 3232 4032 4040 5050N ISO 5610-10 R ISO 5610-11S ISO 5610-12 T ISO 5610-13V ISO 5610-15NOTE “” represents standardized letter symbols and shank sizes. Cells left blank represent non-standardized letter symbols and shank sizes.aPrimary direction of feed.4 Dim

34、ensions4.1 Cross section and length, l1The dimensions of the cross section, depending on the length, l1, and height, h1, of the cutting edge shall be in accordance with Figure 1 and Table 2. ISO 2014 All rights reserved 5BS ISO 5610-1:2014ISO 5610-1:2014(E)Figure 1 Tool holder style KTable 2 Dimensi

35、ons of the cross sectionDimensions in millimetresh1js13h2h13bah13l1k16Series 1 Series 2 Long Short8 8 8 60 4010 10 10 8 70 5012 12 12 10 80 6016 16 16 12 100 7020 20 20 16 125 8025 25 25 20 150 10032 32 32 25 170 12540 40 40 32 200 15050 50 50 40 250 aSeries 1: b = h2; Series 2: b approximately 0,8h

36、2.4.2 Head length, l2The maximum head length, l2, depending on the diameter, d, of the inscribed circle of the indexable inserts, shall be in accordance with Figure 1 and Table 3.The head length given in Table 3 shall not apply to tool holders with indexable insert styles D and V.Table 3 Head length

37、Dimensions in millimetresdl2max.6,35 257,94 289,525 3212,7 366 ISO 2014 All rights reservedBS ISO 5610-1:2014ISO 5610-1:2014(E)dl2max.15,875 4019,05 4525,4 504.3 Dimension fThe dimension f, depending on the width, b, of the cross section and the shape of the tool holder, shall be in accordance with

38、Table 4.Table 4 Dimension fDimensions in millimetresbffor tool holder stylesD, V N B, T A RF, G, H, J, K, L, S0,25+050, +050, +050, +050, +050,8 4 7 8,5 9 1010 5 9 10,5 11 1212 6 11 12,5 13 1616 8 13 16,5 17 2020 10 17 20,5 22 2525 12,5 22 25,5 27 3232 16 27 33 35 4040 20 35 41 43 5050 25 43 51 53 6

39、05 Determination of dimensions5.1 Cutting edge corner5.1.1 Specified point KCase 1: The specified point K shall be defined as follows.Consider planes Pf(assumed working plane) and Ps(tool cutting edge plane), as defined in ISO 3002-1, for a selected point on the major cutting edge (e.g. point of tan

40、gency of major cutting edge with inscribed circle).a) For r90, point K shall be defined as the intersection of plane Ps, a plane parallel to plane Pftangent to the corner radius, and a plane containing the tool face A(see Figures 2 and 3).b) For r90, point K shall be defined as the intersection of a

41、 plane parallel to plane Pftangent to the corner radius, a plane perpendicular to plane Pftangent to the corner radius, and a plane containing the tool face A(see Figures 4 and 5).For tool holders style S, the side rake shall be equal to the back rake. ISO 2014 All rights reserved 7BS ISO 5610-1:201

42、4ISO 5610-1:2014(E)Case 2: For special cases of tool holders styles D and S with round indexable inserts, specified point K shall be defined as follows.a) For tool holders style D (see Figure 6), point K shall be defined as the intersection of a plane parallel to Pfpassing through the axis of the in

43、dexable insert, a plane perpendicular to Pfand tangential to the cutting edge, and a plane containing A.b) For tool holders style S (see Figure 7), there are two cases of point K. These shall be defined by two planes, Pf, in directions of two main perpendicular feeds, which are tangential to the cut

44、ting edge of the indexable insert.KeyaPrimary direction of feed.Figure 2 Cutting edge angle r90, with transverse feedKeyaPrimary direction of feed.Figure 3 Cutting edge angle r90, with longitudinal feed8 ISO 2014 All rights reservedBS ISO 5610-1:2014ISO 5610-1:2014(E)KeyaPrimary direction of feed.Fi

45、gure 4 Cutting edge angle r90, with longitudinal feedKeyaPrimary direction of feed.Figure 5 Cutting edge angle r90, with transverse feedKeyaPrimary direction of feed.Figure 6 Point K for tool style D with round indexable insert ISO 2014 All rights reserved 9BS ISO 5610-1:2014ISO 5610-1:2014(E)KeyaPr

46、imary direction of feed.Figure 7 Point K for tool style S with round indexable insert5.1.2 Theoretical sharp corner, TThe intersection of the theoretical extensions of the major cutting edge and minor cutting edge shall be considered as the theoretical sharp cutting edge corner T (see Figures 2 to 5

47、).NOTE The position of the theoretical corner, T, is independent of the corner radius, r, of the indexable insert.5.2 Corner radius, r, of the master indexable insertsThe values of the corner radius, r, of the master indexable insert (master gauge) used for the determination and testing of length, l

48、1, dimension f, and height, h1shall be in accordance with Table 5.Table 5 Corner radiusDimensions in millimetresdrNominal dimensiona6,350,47,949,5250,812,715,8751,219,0525,4 2,4aThe correction values x and y are derived from the accurate values of the corner radii r= 0,397 mm, 0,794 mm, 1,191 mm, and 2,381 mm, which correspond to the inch dimensions.The corner radius, r, of the master indexable insert shall be a function of the size of the i