BS ISO 5610-12-2014 Tool holders with rectangular shank for indexable inserts Style S《数控刀片的矩形柄刀架 S款》.pdf

1、BSI Standards PublicationBS ISO 5610-12:2014Tool holders with rectangularshank for indexable insertsPart 12: Style SBS ISO 5610-12:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-12:2014.It supersedes BS ISO 5610-12:2010 which is withdrawn.The UK part

2、icipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont

3、ract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83620 6ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho

4、rity of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-12:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 12: Style SPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 12: For

5、me SINTERNATIONAL STANDARDISO5610-12Second edition2014-09-01Reference numberISO 5610-12:2014(E)BS ISO 5610-12:2014ISO 5610-12:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or u

6、tilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyr

7、ight officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-12:2014ISO 5610-12:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 G

8、eneral . 13.2 Tool holder style S for rhombic indexable insert shape C 23.3 Tool holder style S for square indexable insert shape S 43.4 Tool holder style S for round indexable insert shape R . 74 Designation .105 Material .116 Design .116.1 Type of mounting . 116.2 Corner radius, r.116.3 Thickness,

9、 s, of indexable insert . 117 Extent of delivery 128 Marking .12Bibliography .13BS ISO 5610-12:2014ISO 5610-12:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stand

10、ards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta

11、ke part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In pa

12、rticular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements o

13、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see

14、 www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence t

15、o the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces

16、the first edition (ISO 5610-12:2010), of which it constitutes a minor revision.ISO 5610 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Styl

17、e B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-12:2014ISO 5610-12:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved

18、vBS ISO 5610-12:2014BS ISO 5610-12:2014Tool holders with rectangular shank for indexable inserts Part 12: Style S1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style S, i.e. with offset shank and cutting edge angle r= 45 for side cutting.These tool holders are primarily

19、intended for indexable inserts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-

20、2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the la

21、test edition of the referenced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination

22、of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE

23、The values of rake angles and inclination angles shown in the figures are recommended values; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-12:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-12:2014ISO 5610-12:2014(E)3.2 Tool holder style S for rhombic indexable insert

24、 shape CKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style S for rhombic indexable insert C2 ISO 2014 All rights reservedBS ISO 5610-12:2014ISO 5610-12:2014(E)Table 1Dimensions in millim

25、etresSymbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 maxSCSCR 0808 068 8 6,4 4,2 10 8 60 12 2,38SCSCL 0808 06SCSCR 1010 0610 10 6,4 4,2 12 10 70 12 2,38SCSCL 1010 06aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifyi

26、ng the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights reserved 3BS ISO 5610-12:2014ISO 5610-12:2014(E)3.3 Tool holder style S for square indexable insert shape SKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand too

27、l holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style S for square indexable insert S4 ISO 2014 All rights reservedBS ISO 5610-12:2014ISO 5610-12:2014(E)Table 2Dimensions in millimetresSymbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 max.SSSCR 1212 0912 12 9,525 6,1 1

28、6 12 323,97SSSCL 1212 09PSSNR 1212 093,18PSSNL 1212 09CSSPR 1212 09CSSPL 1212 09SSSCR 1616 0916 16 9,525 6,1 20 16 323,97SSSCL 1616 09PSSNR 1616 093,18PSSNL 1616 09CSSPR 1616 09CSSPL 1616 09SSSCR 1616 1216 16 12,7 8,3 20 16 364,76SSSCL 1616 12PSSNR 1616 12PSSNL 1616 12CSSPR 1616 123,18CSSPL 1616 12S

29、SSCR 2020 1220 20 12,7 8,3 25 20 364,76SSSCL 2020 12PSSNR 2020 12PSSNL 2020 12CSSPR 2020 123,18CSSPL 2020 12CSSNR 2525 1225 25 12,7 8,3 32 25 367,94CSSNL 2525 12SSSCR 2525 124,76SSSCL 2525 12PSSNR 2525 12PSSNL 2525 12CSSPR 2525 123,18CSSPL 2525 12aFor the selection of length, l1, the dash can be rep

30、laced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights reserved 5BS ISO 5610-12:2014ISO 5610-12:2014(E)Symbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 max.SSSC

31、R 2525 1525 25 15,875 10,2 32 25 405,56SSSCL 2525 15PSSNR 2525 156,35PSSNL 2525 15CSSPR 2525 1925 25 19,05 12,5 32 25 45 4,76CSSPL 2525 19CSSNR 3225 1232 25 12,7 8,3 32 32 367,94CSSNL 3225 12SSSCR 3225 124,76SSSCL 3225 12PSSNR 3225 12PSSNL 3225 12CSSPR 3225 123,18CSSPL 3225 12CSSNR 3225 1532 25 15,8

32、75 10,2 32 32 40 7,94CSSNL 3225 15SSSCR 3225 1532 25 15,875 10,2 40 32 405,56SSSCL 3225 15PSSNR 3225 156,35PSSNL 3225 15CSSPR 3225 1932 25 19,05 12,5 40 32 45 4,76CSSPL 3225 19SSSCR 3232 1932 32 19,05 12,5 40 32 456,35SSSCL 3232 19PSSNR 3232 19PSSNL 3232 19CSSPR 3232 194,76CSSPL 3232 19SSSCR 4040 19

33、40 40 19,05 12,5 50 40 456,35SSSCL 4040 19PSSNR 4040 19PSSNL 4040 19CSSPR 4040 194,76CSSPL 4040 19PSSNR 4040 2540 40 25,4 16 50 40 50 7,94PSSNL 4040 25aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool len

34、gth, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.Table 26 ISO 2014 All rights reservedBS ISO 5610-12:2014ISO 5610-12:2014(E)Symbolah1b l3a f h2l1al2sbjs13 h13 +050, h13 k16 max.PSSNR 5050 2550 50 25,4 16 60 50 50 7,94PSSNL 5050 25aFor the selection of length, l1, the das

35、h can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.3.4 Tool holder style S for round indexable insert shape RKeyaInclination angle, s.bRake angle, o.NOTE This figure

36、 shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 3 Tool holder style S for round indexable insert RTable 2 ISO 2014 All rights reserved 7BS ISO 5610-12:2014ISO 5610-12:2014(E)Table 3Dimensions in millimetresSymbolah1b d f h2l1al2sbjs13 h13 +050, h13 k16 max.SR

37、SCR 0808 068 8 6 10 8 25 2,38SRSCL 0808 06SRSCR 1010 0610 10612 10 252,38SRSCL 1010 06SRSCR 1010 088 3,18SRSCL 1010 08SRSCR 1212 0612 12616 12 322,38SRSCL 1212 06SRSCR 1212 088 3,18SRSCL 1212 08SRSCR 1616 0616 16620 16 322,38SRSCL 1616 06SRSCR 1616 088 3,18SRSCL 1616 08SRSCR 1616 1010 3,97SRSCL 1616

38、 10SRSCR 2020 0620 20625 20 362,38SRSCL 2020 06SRSCR 2020 088 3,18SRSCL 2020 08SRSCR 2020 1010 3,97SRSCL 2020 10SRSCR 2020 1212 4,76SRSCL 2020 12aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, s

39、ee ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.8 ISO 2014 All rights reservedBS ISO 5610-12:2014ISO 5610-12:2014(E)Symbolah1b d f h2l1al2sbjs13 h13 +050, h13 k16 max.SRSCR 2525 0625 25632 25 402,38SRSCL 2525 06SRSCR 2525 088 3,18SRSCL 2525 08CRSNR 2525 099,52 4,76CRSNL 2525

40、09SRSCR 2525 1010 3,97SRSCL 2525 10SRSCR 2525 1212 4,76SRSCL 2525 12PRSNR 2525 12PRSNL 2525 12CRSNR 2525 1212,7 7,94CRSNL 2525 12SRSCR 2525 1616 5,56SRSCL 2525 16SRSCR 3225 123225123232 40 4,76SRSCL 3225 12CRSNR 3225 1212,7 36 7,94CRSNL 3225 12SRSCR 3225 1616 40 5,56SRSCL 3225 16CRSNR 3232 123212,7

41、36 7,94CRSNL 3232 12PRSNR 3232 1919,05 4040 6,35PRSNL 3232 19CRSNR 3232 1945 7,94CRSNL 3232 19SRSCR 3232 2032 32 20 40 32 45 6,35SRSCL 3232 20PRSCR 3232 20PRSCL 3232 20aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identif

42、ying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.Table 3 ISO 2014 All rights reserved 9BS ISO 5610-12:2014ISO 5610-12:2014(E)Symbolah1b d f h2l1al2sbjs13 h13 +050, h13 k16 max.SRSCR 4040 2540 402550 40 507,94SRSCL 4040 25PRSCR 4040 25PRSCL 4040 25CRSNR 4

43、040 2525,4CRSNL 4040 25PRSNR 4040 259,52PRSNL 4040 25aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool

44、holder in accordance with this part of ISO 5610 shall be designated by:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-12);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordanc

45、e with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holde

46、r for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style S (S), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:To

47、ol holder ISO 5610-12 - SCSCR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) square indexable insert shape S (S), tool holder style S (S), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1=

48、170 mm (P), for cutting edge length l3= 12,7 mm (12) is designated as follows:Tool holder ISO 5610-12 - PSSNR 3225 P12EXAMPLE 3 Tool holder for countersunk screw-clamped (S) round indexable insert shape R (R), tool holder style S (S), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 20 mm and width b = 20 mm (2020), length l1= 125 mm (K), diameter d = 10 mm (10) is designated as follows:Tool holder ISO 5610-12 - SRSCR 2020