BS ISO 5610-15-2014 Tool holders with rectangular shank for indexable inserts Style V《数控刀片的矩形柄刀架 V款》.pdf

1、BSI Standards PublicationBS ISO 5610-15:2014Tool holders with rectangularshank for indexable insertsPart 15: Style VBS ISO 5610-15:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-15:2014.It supersedes BS ISO 5610-15:2010 which is withdrawn.The UK part

2、icipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont

3、ract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83623 7ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho

4、rity of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-15:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 15: Style VPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 15: For

5、me VINTERNATIONAL STANDARDISO5610-15Second edition2014-09-01Reference numberISO 5610-15:2014(E)BS ISO 5610-15:2014ISO 5610-15:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or u

6、tilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyr

7、ight officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-15:2014ISO 5610-15:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 G

8、eneral . 13.2 Tool holder style V for rhombic indexable insert shape V . 24 Designation 35 Material 36 Design 36.1 Type of mounting 36.2 Corner radius, r46.3 Thickness s of indexable insert . 47 Extent of delivery . 48 Marking 4Bibliography 5BS ISO 5610-15:2014ISO 5610-15:2014(E)ForewordISO (the Int

9、ernational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee ha

10、s been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical

11、standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in acc

12、ordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Deta

13、ils of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an e

14、ndorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee res

15、ponsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-15:2010), of which it constitutes a minor revision.ISO 5610 consists of the following parts, under the general

16、 title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part

17、 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-15:2014ISO 5610-15:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-15:2014BS ISO 5610-15:2014Tool holders with rectangular shank for indexable inserts Part 15: Style V1 ScopeThis part of ISO 5

18、610 specifies tool holders with rectangular shank, style V, i.e. with straight shank and cutting edge angle r= 72,5 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning oper

19、ations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are n

20、ormatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartrid

21、ges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensi

22、ons given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended values; they can vary according to the applicati

23、on.INTERNATIONAL STANDARD ISO 5610-15:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-15:2014ISO 5610-15:2014(E)3.2 Tool holder style V for rhombic indexable insert shape VKeyaInclination angle, s.bRake angle, o.Figure 1 Tool holder style V for rhombic indexable insert VTable 1Dimensions in millim

24、etresSymbolah1js13bh13l3f0,25h2h13l1ak16l2max.sbSVVBN 1212 11 12 12 11,1 6 12 253,18SVVBN 1616 11 16 16 11,1 8 16 25SVVBN 2020 16 20 20 16,6 10 20 40 4,76aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool

25、length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.2 ISO 2014 All rights reservedBS ISO 5610-15:2014ISO 5610-15:2014(E)Symbolah1js13bh13l3f0,25h2h13l1ak16l2max.sbSVVBN 2525 16 25 25 16,6 12,5 25 40 4,76SVVBN 3225 16 32 25 16,6 12,5 32 40 4,76aFor the selection of length

26、, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the follow

27、ing:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-15);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance

28、, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE Tool holder for a screw-clamped (S) rhombic indexable insert shape V (V), tool

29、holder style V (V), for normal clearance of indexable insert n= 5 (B), left- and right-hand cutting (N), with height h1= 20 mm and width b = 20 mm (2020), length l1= 125 mm (K), for cutting edge length l3= 11,1 mm (11) is designated as follows:Tool holder ISO 5610-15 - SVVBN 2020 K115 MaterialThe ma

30、terial should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Table 1.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the

31、 designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Table 1, the relevant indexable insert thickness shall also be considered.Table 1 ISO 2014 All rights re

32、served 3BS ISO 5610-15:2014ISO 5610-15:2014(E)6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Table 1, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to

33、tool holders with indexable inserts having corner radii, r, in accordance with Table 2.Table 2Dimensions in millimetresl3r11,1 0,416,6 0,8NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner

34、radii, r, other than those specified in Table 2, the dimension l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness s of indexable insertThe values for thickness s gi

35、ven in Table 1 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool h

36、olders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by

37、mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-15:2014, shall be given on the packaging.4 ISO 2014 All rights reservedBS ISO 5610-15:2014ISO 5610-15:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 300

38、2-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexa

39、ble hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary

40、 for tool items ISO 2014 All rights reserved 5BS ISO 5610-15:2014ISO 5610-15:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, informat

41、ion and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government,

42、 consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all

43、sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying stand

44、ardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard cop

45、ies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and ado

46、pted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, b

47、y becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, pleas

48、e visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .Revisio

49、nsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documenta