BS ISO 5610-3-2014 Tool holders with rectangular shank for indexable inserts Style B《数控刀片的矩形柄刀架 B款》.pdf

1、BSI Standards PublicationBS ISO 5610-3:2014Tool holders with rectangularshank for indexable insertsPart 3: Style BBS ISO 5610-3:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-3:2014. Itsupersedes BS ISO 5610-3:2010 which is withdrawn.The UK participa

2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.

3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83611 4ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-3:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 3: Style BPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 3: Forme BINTE

5、RNATIONAL STANDARDISO5610-3Second edition2014-09-01Reference numberISO 5610-3:2014(E)BS ISO 5610-3:2014ISO 5610-3:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe

6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC

7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-3:2014ISO 5610-3:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2

8、Tool holder style B for rhombic indexable insert shape C . 23.3 Tool holder style B for square indexable insert shape S . 44 Designation 65 Material 76 Design 76.1 Type of mounting 76.2 Corner radius, r76.3 Thickness, s, of indexable insert . 77 Extent of delivery . 88 Marking 8Bibliography 9BS ISO

9、5610-3:2014ISO 5610-3:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intereste

10、d in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Com

11、mission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents

12、should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible fo

13、r identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the

14、convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Fore

15、word - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-3:2010), of which it constitutes a minor revision.ISO 5610 co

16、nsists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9

17、: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-3:2014ISO 5610-3:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-3:2014BS ISO 5610-3:2014Tool holders with rectangular shank for indexable inser

18、ts Part 3: Style B1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style B, i.e. with straight shank and cutting edge angle r= 75 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials intended to be m

19、ounted by clamping and be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe

20、following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:201

21、2, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with

22、 the pictorial representation; only the dimensions given shall be observed.For the determination of dimensions h1, f, and l1, see ISO 5610-1.For an explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recomm

23、ended values; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-3:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-3:2014ISO 5610-3:2014(E)3.2 Tool holder style B for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand

24、 tool holder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style B for rhombic indexable insert CTable 1Dimensions in millimetresSymbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbSCBCR 0808 068 8 6,4 1,6 7 8 12 2,38SCBCL 0808 06SCBCR 1010 0610 10 6,4 1,6 9 10 12 2,38SCBCL 1010 06

25、aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.2 ISO 2014 All rights reservedBS ISO 5610-3:2014ISO 5610-3:2014(E)Symbola

26、h1js13bh13l3af+050,h2h13l1ak16l2max.sbSCBCR 1212 0612 12 6,4 1,6 10 12 12 2,38SCBCL 1212 06aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without sh

27、im, if applicable.Table 1 ISO 2014 All rights reserved 3BS ISO 5610-3:2014ISO 5610-3:2014(E)3.3 Tool holder style B for square indexable insert shape SKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 To

28、ol holder style B for square indexable insert S4 ISO 2014 All rights reservedBS ISO 5610-3:2014ISO 5610-3:2014(E)Table 2Dimensions in millimetresSymbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbSSBCR 1616 0916 16 9,52 2,2 13 16 32 3,18SSBCL 1616 09PSBNR 1616 09PSBNL 1616 09CSBPR 1616 09CSBPL 1616 09SSBC

29、R 2020 1220 20 12,7 3,1 17 20 364,76SSBCL 2020 12PSBNR 2020 12PSBNL 2020 12CSBPR 2020 123,18CSBPL 2020 12SSBCR 2525 1225 25 12,7 3,1 22 25 364,76SSBCL 2525 12PSBNR 2525 12PSBNL 2525 12CSBPR 2525 123,18CSBPL 2525 12SSBCR 2525 1525 25 15,88 3,9 22 25 405,56SSBCL 2525 15PSBNR 2525 156,35PSBNL 2525 15SS

30、BCR 3225 1232 25 12,7 3,1 22 32 364,76SSBCL 3225 12PSBNR 3225 12PSBNL 3225 12CSBPR 3225 123,18CSBPL 3225 12SSBCR 3225 1532 25 15,88 3,9 27 32 405,56SSBCL 3225 15PSBNR 3225 156,35PSBNL 3225 15aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For

31、 letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights reserved 5BS ISO 5610-3:2014ISO 5610-3:2014(E)Symbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbSSBCR 3232 1932 32 19,05 4,6 27 32 456,35SSBCL 3232 19PSBNR 3232 19PSB

32、NL 3232 19CSBPR 3232 194,76CSBPL 3232 19SSBCR 4040 1940 40 19,05 4,6 35 40 456,35SSBCL 4040 19PSBNR 4040 19PSBNL 4040 19CSBPR 4040 194,76CSBPL 4040 19PSBNR 5050 2550 50 25,4 5,9 43 50 50 7,94PSBNL 5050 25aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014,

33、 Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. I

34、SO 5610-3);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordan

35、ce with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style B (B), for normal clearance of indexable insert n= 7 (

36、C), right-hand type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-3 - SCBCR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) square indexable insert shape S

37、(S), tool holder style B (B), normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 12,7 mm (12) is designated as follows:Table 26 ISO 2014 All rights reservedBS ISO 5610-3:2014ISO 5610

38、-3:2014(E)Tool holder ISO 5610-3 - PSBNR 3225 P125 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at

39、the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant ind

40、exable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2

41、apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3r6,4 0,49,520,812,715,881,219,0525,4 2,4NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm 1,191

42、 mm, and 2,381 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of a, f, and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicabl

43、e.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicate

44、d when ordering or upon delivery (in the handbook). ISO 2014 All rights reserved 7BS ISO 5610-3:2014ISO 5610-3:2014(E)7 Extent of deliveryThe tool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol an

45、d the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-3:2014, shall be given on the packaging.8 ISO 2014 All rights reservedBS ISO 5610-3

46、:2014ISO 5610-3:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angle

47、s, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchan

48、ge Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items ISO 2014 All rights reserved 9BS ISO 5610-3:2014ISO 5610-3:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 9 pagesThis page

49、 deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group