BS ISO 5610-4-2014 Tool holders with rectangular shank for indexable inserts Style D《数控刀片的矩形柄刀架 D款》.pdf

1、BSI Standards PublicationBS ISO 5610-4:2014Tool holders with rectangularshank for indexable insertsPart 4: Style DBS ISO 5610-4:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-4:2014. Itsupersedes BS ISO 5610-4:2010 which is withdrawn.The UK participa

2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.

3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83612 1ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority

4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-4:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 4: Style DPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 4: Forme DINTE

5、RNATIONAL STANDARDISO5610-4Second edition2014-09-01Reference numberISO 5610-4:2014(E)BS ISO 5610-4:2014ISO 5610-4:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe

6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC

7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-4:2014ISO 5610-4:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2

8、Tool holder style D for square indexable insert shape S . 23.3 Tool holder style D for round indexable insert shape R 44 Designation 65 Material 76 Design 76.1 Type of mounting 76.2 Corner radius, r76.3 Thickness, s, of indexable insert . 77 Extent of delivery . 78 Marking 8Bibliography 9BS ISO 5610

9、-4:2014ISO 5610-4:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in

10、 a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commiss

11、ion (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents shou

12、ld be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for id

13、entifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the conv

14、enience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword

15、 - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-4:2010), of which it constitutes a minor revision.ISO 5610 consis

16、ts of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: St

17、yle L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-4:2014ISO 5610-4:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-4:2014BS ISO 5610-4:2014Tool holders with rectangular shank for indexable inserts P

18、art 4: Style D1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style D, i.e. with straight shank and cutting edge angle r= 45 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials intended to be mount

19、ed by clamping and used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe followi

20、ng documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012, Turn

21、ing and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pi

22、ctorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended values;

23、they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-4:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-4:2014ISO 5610-4:2014(E)3.2 Tool holder style D for square indexable insert shape SKeyaInclination angle, s.bRake angle, o.Figure 1 Tool holder style D for square indexable

24、insert S2 ISO 2014 All rights reservedBS ISO 5610-4:2014ISO 5610-4:2014(E)Table 1Dimensions in millimetresSymbolah1js13b h13l3f 0,25h2h13l1ak16l2max.sbSSDCN 1212 0912 12 9,52 6 12 323,97PSDNN 1212 093,18CSDPN 1212 09SSDCN 1616 0916 16 9,52 8 16 323,97PSDNN 1616 093,18CSDPN 1616 09SSDCN 2020 1220 20

25、12,7 10 20 364,76PSDNN 2020 12CSDPN 2020 12 3,18CSDNN 2525 1225 25 12,7 12,5 25 367,94SSDCN 2525 124,76PSDNN 2525 12CSDPN 2525 12 3,18CSDNN 3225 1232 25 12,7 12,5 32 367,94SSDCN 3225 124,76PSDNN 3225 12CSDPN 3225 12 3,18SSDCN 3232 1932 32 19,05 16 32 456,35PSDNN 3232 19CSDPN 3232 19 4,76aFor the sel

26、ection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights reserved 3BS ISO 5610-4:2014ISO 5610-4:2014(E)3.3 Tool holde

27、r style D for round indexable insert shape RKeyaInclination angle, s.bRake angle, o.Figure 2 Tool holder style D for round indexable insert RTable 2Dimensions in millimetresSymbolah1js13b h13d f 0,25h2h13l1ak16sbSRDCN 0808 068 8 6 4 8 2,38PRDCN 0808 06aFor the selection of length, l1, the dash can b

28、e replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 ISO 2014 All rights reservedBS ISO 5610-4:2014ISO 5610-4:2014(E)Symbolah1js13b h13d f 0,25h2h13l1ak16sbSRDCN 1010 0

29、610 1065 10 2,38PRDCN 1010 06SRDCN 1010 088 3,18PRDCN 1010 08SRDCN 1212 0612 1266 12 2,38PRDCN 1212 06SRDCN 1212 088 3,18PRDCN 1212 08SRDCN 1616 0616 1668 16 2,38PRDCN 1616 06SRDCN 1616 088 3,18PRDCN 1616 08SRDCN 1616 1010 3,97PRDCN 1616 10SRDCN 2020 0620 20610 20 2,38PRDCN 2020 06SRDCN 2020 088 3,1

30、8PRDCN 2020 08SRDCN 2020 1010 3,97PRDCN 2020 10SRDCN 2020 1212 4,76PRDCN 2020 12SRDCN 2525 0625 25612,5 25 2,38PRDCN 2525 06SRDCN 2525 088 3,18PRDCN 2525 08CRDNN 2525 09 9,52 4,76SRDCN 2525 1010 3,97PRDCN 2525 10SRDCN 2525 1212 4,76PRDCN 2525 12CRDNN 2525 12 12,7 7,94SRDCN 2525 1616 6,35PRDCN 2525 1

31、6aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.Table 2 ISO 2014 All rights reserved 5BS ISO 5610-4:2014ISO 5610-4:2

32、014(E)Symbolah1js13b h13d f 0,25h2h13l1ak16sbSRDCN 3225 1232 251212,5 32 4,76PRDCN 3225 12CRDNN 3225 12 12,77,94CRDNN 3225 15 15,88SRDCN 3225 1616 6,35PRDCN 3225 16CRDNN 3232 1932 3219,0516 32 7,94SRDCN 3232 2020 6,35PRDCN 3232 20SRDCN 4040 2540 402520 40 7,94PRDCN 4040 25CRDNN 4040 25 25,4aFor the

33、selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be d

34、esignated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-4);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable i

35、nsert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a horizontally mounted bore-clamped (P)

36、 square indexable insert shape S (S), tool holder style D (D), for normal clearance of indexable insert n= 0 (N), cutting on both sides (N), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 12,7 mm (12) is designated as follows:Tool holder ISO 5610

37、-4 - PSDNN 3225 P12EXAMPLE 2 Tool holder for countersink screw-clamped (S) round indexable insert shape R (R), tool holder style D (D), for normal clearance of indexable insert n= 7 (C), cutting on both sides (N), with height h1= 25 mm and width b = 25 mm (2525), length l1= 150 mm (M), for diameter

38、d = 12 mm (12) is designated as follows:Tool holder ISO 5610-4 - SRDCN 2525 M12Table 26 ISO 2014 All rights reservedBS ISO 5610-4:2014ISO 5610-4:2014(E)5 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders w

39、ith indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in acc

40、ordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as sp

41、ecified in Table 1, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3r9,520,812,719,05 1,2NOTE The values given for rare nominal values. The a

42、ccurate values converted from the inch dimensions are 0,794 mm and 1,191 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of f shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with maste

43、r indexable insert and master shim, if any.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specifie

44、d values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryThe tool holders shall be delivered complete with clamping device, but without indexable insert(s). ISO 2014 All rights reserved 7BS ISO 5610-4:2014ISO 5610-4:2014(E)8 MarkingTool holders

45、shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-4:2014, shall be given on the packaging.8

46、ISO 2014 All rights reservedBS ISO 5610-4:2014ISO 5610-4:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms,

47、reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cu

48、tting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items ISO 2014 All rights reserved 9BS ISO 5610-4:2014ISO 5610-4:2014(E) ISO 2014 All rights reservedICS

49、 25.100.01Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are publish