BS ISO 5611-2-2015 Cartridges type A for indexable inserts Style F《可转位A型刀夹头 F型》.pdf

1、BSI Standards PublicationBS ISO 5611-2:2015Cartridges, type A, forindexable insertsPart 2: Style FBS ISO 5611-2:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5611-2:2015.Together with BS ISO 5611-1, BS ISO 5611-3, BS ISO 5611-4, BS ISO5611-5, BS ISO 5611

2、-6, BS ISO 5611-7, BS ISO 5611-8, BS ISO 5611-9,BS ISO 5611-10, BS ISO 5611-11 and BS ISO 5611-12 it supersedes BS 4193-8:1997 (dual numbered as ISO 5611:1995) which will bewithdrawn upon publication of the rest of the parts in this series.The UK participation in its preparation was entrusted to Tec

3、hnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplic

4、ation. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 88413 9ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committe

5、e on 30 November 2015.Amendments/corrigenda issued since publication Date Text affectedBS ISO 5611-2:2015 ISO 2015Cartridges, type A, for indexable inserts Part 2: Style FCartouches du type A, plaquettes amovibles Partie 2: Forme FINTERNATIONAL STANDARDISO5611-2First edition2015-11-01Reference numbe

6、rISO 5611-2:2015(E)BS ISO 5611-2:2015ISO 5611-2:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, elect

7、ronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier

8、, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 5611-2:2015ISO 5611-2:2015(E)Foreword iv1 Scope . 12 Normative references 13 Dimensions . 14 Designation 45 Material 56 Design 56.1 Method of holding 56.2 Corner radius r.56.3 Adjusting screw 67 Extent of

9、 delivery . 68 Marking 6 ISO 2015 All rights reserved iiiContents PageBS ISO 5611-2:2015ISO 5611-2:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norm

10、ally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in t

11、he work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the

12、 different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this docume

13、nt may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/

14、patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO prin

15、ciples in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This first edition of ISO 5611-2, together with ISO 561

16、1-1, ISO 5611-3, ISO 5611-4, ISO 5611-5, ISO 5611-6, ISO 5611-7, ISO 5611-8, ISO 5611-9, ISO 5611-10, ISO 5611-11, and ISO 5611-12, cancels and replaces ISO 5611:1995, which has been technically revised.ISO 5611 consists of the following parts, under the general title Cartridges, type A, for indexab

17、le inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style F Part 3: Style G Part 4: Style J Part 5: Style K Part 6: Style L Part 7: Style R Part 8: Style S Part 9: Style T Part 10: Style U Part 11: Style W Part 12: Style Yiv ISO 2015 All rights reservedBS ISO 5611

18、-2:2015INTERNATIONAL STANDARD ISO 5611-2:2015(E)Cartridges, type A, for indexable inserts Part 2: Style F1 ScopeThis part of this ISO 5611 applies for cartridges type A, with hole(s) for fastening screw(s), of style F, i.e. with cutting edge angle r= 90 for end cutting.Cartridges are intended to be

19、used with indexable inserts made of hard metal, ceramic, or other cutting materials and are primarily mounted to be used for internal turning of operations.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its ap

20、plication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1832, Indexable inserts for cutting tools D esignationISO 5608, Turning and copying tool holders and cartridges for indexable

21、inserts D esignationISO 5611-1, Cartridges, type A, for indexable inserts Part 1: General survey, correlation and determination of dimensions3 DimensionsCartridges type A need not comply with the pictorial representation, only the dimensions given shall be observed.For determination of dimensions h1

22、, f and l1see ISO 5611-1. For explanation of the designation code for cartridges, see ISO 5608.4NOTE For other dimensions, see Figure 2Figure 1 Style F with height h1= 6 mm and 8 mm with rhombic indexable insert ISO 2015 All rights reserved 1BS ISO 5611-2:2015ISO 5611-2:2015(E)Figure 2 Style F with

23、height h1= 8 mm, 10 mm, 12 mm, 16 mm and 20 mm with triangular insertFigure 3 Style F with height h1= 25 mm with triangular indexable insertFigure 4 Sectional drawing A-A at height h1= 6 mm, 8 mm, 10 mm and 12 mm2 ISO 2015 All rights reservedBS ISO 5611-2:2015ISO 5611-2:2015(E)Figure 5 Sectional dra

24、wing A-A at height h1= 16 mm, 20 mm and 25 mmNOTE Pictured is a right hand cartridge (Figure 4); left hand cartridge (Figure 5) laterally reversed.Table 1Dimensions in millimetresSymbolah1l4b d1bd2ce f h2l1l2l3tFastening screw0,08 0 0,2 min. H130 0,080 0,2 min. 0,13SCFPR 06CA 056 5,6 6 20 4 12 8 8,5

25、 25 16 4,5 3,5 M3,5SCFPL 06CA 05SCFCR 08CA 068 6,4 8 25 4,5 17 10 11 32 21,5 6 4,5 M4SCFCL 08CA 06STFCR 08CA 098 9,6 8 25 4,5 17 10 11 32 21,5 6 4,5 M4STFCL 08CA 09STFCR 10CA 1110 11 11 40 7 20 14 15 50 26 8 5 M6STFCL 10CA 11CTFPR 12CA 1112 11 16 50 7 20 20 20 55 26 8 6 M6CTFPL 12CA 11STFCR 12CA 161

26、2 16,5 16 50 7 20 20 20 55 26 8 6 M6STFCL 12CA 16PTFNR 12CA 16PTFNL 12CA 16aCartridges for indexable inserts for holding horizontally mounted with hole clamping (first letter symbol P) can be equipped with additional top and hole clamping; the letter symbol replaced P by M in this case.bSmallest pos

27、sible internal diameter for operating.cThe hole for fastening screws of the cartridges can be designed also as slotted hole at the manufacturers option. ISO 2015 All rights reserved 3BS ISO 5611-2:2015ISO 5611-2:2015(E)Symbolah1l4b d1bd2ce f h2l1l2l3tFastening screw0,08 0 0,2 min. H130 0,080 0,2 min

28、. 0,13CTFPR 16CA 1616 16,5 20 60 9 25 25 25 63 32,5 8 M8CTFPL 16CA 16PTFNR 16CA 16PTFNL 16CA 16STFCR 16CA 22STFCL 16CA 22PTFNR 20CA 2220 22 20 70 9 30 25 30 70 37, 5 10 M8PTFNL 20CA 22PTFNR 25CA 2725 27, 5 25 100 11 30 32 35 100 59 10 M10PTFNL 25CA 27aCartridges for indexable inserts for holding hor

29、izontally mounted with hole clamping (first letter symbol P) can be equipped with additional top and hole clamping; the letter symbol replaced P by M in this case.bSmallest possible internal diameter for operating.cThe hole for fastening screws of the cartridges can be designed also as slotted hole

30、at the manufacturers option.4 DesignationA cartridge in accordance with this part of ISO 5611 shall be designated by:a) “Cartridge”;b) reference of this part of ISO 5611, i.e. ISO 5611-2;c) letter symbol identifying the method of holding the insert, in accordance with ISO 5608;d) letter symbol ident

31、ifying insert shape, in accordance with ISO 1832;e) letter symbol identifying cartridge style, in accordance with ISO 5608;f) letter symbol identifying insert normal clearance, in accordance with ISO 1832;g) letter symbol identifying hand of cartridge, in accordance with ISO 5608;h) number symbol id

32、entifying tool height (shank height of cartridges and height of cutting edge), in accordance with ISO 5608;i) number symbol identifying tool holder shank width or, for cartridges, letter C followed by a letter symbol identifying the cartridge type, in accordance with ISO 5608;j) letter symbol identi

33、fying tool length, in accordance with ISO 5608;k) number symbol identifying indexable insert size, in accordance with ISO 1832.EXAMPLE Cartridge with screw clamping through hole (S) triangular indexable insert shape (T), cartridge style F (F), for the insert normal clearance 7 (C), right hand cartri

34、dge (R), with height h1= 12 mm (12), cartridge Type A (CA), length l1= 55 mm (), edge length l4= 16,5 mm (16) is designated as follows:Cartridge ISO 56112 STFCR 12CA 16Table 1 (continued)4 ISO 2015 All rights reservedBS ISO 5611-2:2015ISO 5611-2:2015(E)5 MaterialSteel with a tensile strength of at l

35、east 1 200 N/mm2.6 Design6.1 Method of holding(first letter symbol identifying the method of holding the insert)6.1.1 Cartridge for indexable inserts with insert normal clearance n= 7(fourth symbol identifying insert normal clearance C) holding screw clamping through hole; letter symbol S, e.g. SCFC

36、R.6.1.2 Cartridge for indexable inserts with insert normal clearance n= 7(fourth symbol identifying insert normal clearance C) holding screw clamping through hole; letter symbol S, e.g. SCFCR.6.1.3 Cartridge for indexable inserts with insert normal clearance n= 0(fourth symbol identifying insert nor

37、mal clearance N) holding with hole clamping; letter symbol P, e.g. PTFNR.6.2 Corner radius rCartridges in accordance with this part of ISO 5611 can be equipped with indexable inserts with cutting edge lengths l4as specified in Table 1 and any corner radius r.The values for f given in Table 1 apply t

38、o cartridges with indexable inserts having corner radii rin accordance with Table 2.For cartridges with indexable inserts with corner radii other than those specified in Table 2, the dimensions of f shall be determined in accordance with ISO 5611-1.The tolerances on h1and f refer to dimensions measu

39、red with master indexable insert and master shim, if any. ISO 2015 All rights reserved 5BS ISO 5611-2:2015ISO 5611-2:2015(E)Table 2Dimensions in millimetresl4rC T5,6 0,46,4 9,6 11 16,50,8 22 27, 5 1,2NOTE The values given for rare nominal values. The accurate values converted from the inch dimension

40、s are 0,397 mm; 0,794 mm and 1,191 mm.6.3 Adjusting screwFor the adjustment of the cartridge in the direction of the f dimension, it is the manufacturers option to equip the cartridge with an adjustment screw.7 Extent of deliveryCartridges to be delivered with complete clamping device and adjusting

41、screws.8 MarkingCartridges shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking depends on the manufacturers option or upon agreement.Deviations in marking are based upon agreement.The general number of this International Standard (ISO 5611) shall b

42、e given on the packaging.6 ISO 2015 All rights reservedBS ISO 5611-2:2015BS ISO 5611-2:2015ISO 5611-2:2015(E) ISO 2015 All rights reservedICS 25.100.01Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-relat

43、ed publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together busine

44、ss, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of

45、all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Know

46、ledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Developmen

47、t Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to ov

48、er 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy a

49、nd subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit