BS ISO 5692-1-2004 Agricultural vehicles - Mechanical connections on towed vehicles - Dimensions for hitch-rings《农用车辆 拖挂车辆的机械连接装置 挂接环的尺寸》.pdf

1、BRITISH STANDARD BS ISO 5692-1:2004 Agricultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for hitch rings ICS 65.060.10 BS ISO 5692-1:2004 This British Standard was published under the authority of the Standards Policy and S t r a t e g y C o m m i t t e e o n 10 May 2004

2、 BSI 10 May 2004 ISBN 0 580 43756 6 National foreword This British Standard reproduces verbatim ISO 5692-1:2004 and implements it as the UK national standard. It supersedes BS 5891:1980 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultur

3、al tractors and forestry machinery, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the B

4、SI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for

5、 its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK inte

6、rests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5 and a back cover. The BSI copyright notice displayed

7、in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 5692-1 First edition 2004-04-01 Reference number ISO 5692-1:2004(E) Agricultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for

8、 hitch rings Vhicules agricoles Liaisons mcaniques sur vhicules remorqus Partie 1: Dimensions des anneaux dattelageBSISO56921:2004ii id FDPscalimer ThFDP si fam eliy ctnome niat deddebyepfa.sec In cacnadrociw eth sebodA sneciliycilop gn, thf siam elirp eb ytnide or viewb detu llahs ton tide ebed lnu

9、et sst ehyfepcaa hcihw serdebme et desnecil era dedo tsni dnat no dellahpmoc eturep reformign ttide ehign. In odt gnidaolnwsih liferap ,tcca seitpe trehnie snopser ehtitiliby fo nto fnirA gnigniycilop gnisnecil sebod. Teh SItneC Olar Seerctraiat catpecs ibail ontily t nih.aera si Aebod t a sirrameda

10、k fo AsyS ebodtmeI snocrropta.de teDlias fo tfos ehtwcudorp erats t desutaerc ot esih FDP fb nac elif et ni dnuoG ehreneI lafnr oleative tt of eh;eli tP ehDF-rctaenoi temaraptpo erew sremizif deorp rinti.gn Evrey t neeb sah eracakt neo rusnee ttah tf ehtius si elibaf elosu re by ISO memdob rebsei. I

11、n eht kilnuyle evtne ttah a borplme rtaleit gno it si f,dnuo esaelp ifnrom thtneC erla ceSrteraita ta teh sserdda vigoleb new. IOS 4002 Alr lithgs reresv.de sselnU toesiwreh sficep,dei rap ont fo thbup silitaciam nocudorper eb yde or tuilidez na nif yorm ro by nam ysnae, tcelerm ro cinocinahcela, to

12、hp gnidulcnicopom dna gniyicrfomli, tiwuoht repsimsi noin wrtif gnirtie mohI reSO ta the asserdd ebwol or ISOmem sreb obyd t nitnuoc ehry fo teh euqertsre. SIc Oopyrigho tfifce saCsop etela 65 -HCG 1121eneva 02 T.le 22 14 + 10 947 11 Fxa + 22 14 0 94774 9 Eam-il ocpyrithgios.ogr Web wwwi.soo.rg Pbun

13、i dehsil Stiwrezldna BSISO56921:2004 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member b

14、ody interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electro

15、technical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted

16、by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent r

17、ights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5692-1 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tr a c t o r s. This first edition of ISO 5692-1, together with ISO 5692-2:2002, c

18、ancels and replaces ISO 5692:1979 which has been technically revised. ISO 5692 consists of the following parts, under the general title Agricultural vehicles Mechanical connections on towed vehicles: Part 1: Dimensions for hitch rings Part 2: Coupling ring 40 with socket BSISO56921:2004. vi ANRETNII

19、TOTS LANDNADRA OSI -29654002:1)E(1 Agricultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for hitch rings 1S c o p e This part of ISO 5692 specifies the requirements for the attachment of agricultural non-balanced trailers and implements by means of hitch rings to the rear

20、 of the towing vehicle equipped with either a hook as specified in ISO 6489-1, or a piton-type coupling as specified in ISO 6489-4. Its purpose is to ensure the interchangeability of mechanical connections on agricultural towed vehicles. This part of ISO 5692 is applicable to rings whose coupling po

21、int is below the centre-line of the rear axle and below the power take-off (PTO) of the tractor. NOTE Other International Standards are under development for rings coupled above the PTO. 2 Normative references The following referenced documents are indispensable for the application of this document.

22、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6489-1, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 1: Dimensions of hitch-hooks ISO 6489-4, Ag

23、ricultural vehicles Mechanical connections between towed and towing vehicles Part 4: Dimensions of piton-type coupling 3 Interchangeability dimensions 3.1 General The hitch ring and the shank shall have the dimensions shown in Figures 1 and 2. Interchangeability is ensured provided that the attachme

24、nt on the towing vehicle is in accordance with ISO 6489-1 or ISO 6489-4. BSISO56921:20042 3.2 Trailer shank travel angles When the trailer shank fitted with the specified hitch ring is fixed to the tractor attachment, the shank shall be free to turn so that the angles formed with the horizontal situ

25、ated in the tractors plane of symmetry and passing through the coupling point have the following minimum values. a) Angle of yaw: rotation around a vertical axis passing through the coupling point, minimum value of on both sides. b) Angle of pitch: rotation around a horizontal axis passing through t

26、he coupling point and perpendicular to the vehicles longitudinal plane of symmetry, minimum value top and bottom. Allowance should be made for the towing vehicle being up to from horizontal, due to front/rear tyre sizes. c) Angle of roll: rotation around a horizontal axis passing through the couplin

27、g point and located in the vehicles plane of symmetry, minimum value top and bottom. 4 Constructional requirements Hitch rings in accordance with this part of ISO 5692 shall be substantially toroidal and shall be manufactured by forging. Shanks shall be forged or machined or both. The hitch ring sha

28、ll be fixed on the shank. The hitch hook or piton-type coupling on the tractor shall be designed to allow the travel angles specified in 3.2. In addition to these requirements relating to fixed hitch rings for towed vehicles, only the towed member (i.e. hitch ring and shank) shall have the option of

29、 providing rotational freedom of up to around the shanks horizontal longitudinal axis (roll). Limitation of rotation away from the horizontal, or bias towards the hitch ring remaining horizontal, is optional. Dimensions in millimetres Figure 1 Hitch ring dimensions 60 20 3 20 360 BSISO56921:2004 ISO

30、 4002 r llAithgs reservde 3 Dimensions in millimetres Figure 2 Hitch shank dimensions BSISO56921:20044 Annex A (informative) Permissible mechanical connection combinations between towed and towing vehicles Towing vehicle Towed vehicle ISO 6489-1:1991 hook type ISO 5692:1979/ISO 5692-1:2004 hitch rin

31、g ( hole centre,ring diameter) ISO 6489-1:2001 hook type a ISO 5692:1979/ISO 5692-1:2004 hitch ring ( hole centre,ring diameter) ISO 20019:2001 hitch ring ( hole centre, to ring diameter) ISO 6489-2:2002 bolt type ISO 5692-2:2002 coupling ring ( socket) ISO 8755:1986 drawbar coupling b ISO 1102:1986

32、 drawbar coupling b ISO 6489-3: ddrawbar (Cat 2) ISO 5692:1979/ISO 5692-1:2004 hitch ring ( hole centre,ring diameter) c ISO 5692-2:2002 coupling ring ( socket) ISO 8755:1986 drawbar coupling ISO 1102:1986 drawbar coupling c ISO 6489-4:2004 piton type ISO 5692:1979/ISO 5692-1:2004 hitch ring ( hole

33、centre,ring diameter) ISO 24347 eball type ISO 24347 e( ball diameter) Only the combinations given above are recommended. a Connecting an ISO 6489-1:2001 hook, manufactured in accordance with the maximum sizes permitted, to hitch rings in accordance with ISO 5692-1 and of minimum dimensions ( ring d

34、iameter) according to ISO 20019 could result in a “jerky” connection between the tractor and the trailer and result in less driving comfort. b Primarily used on trailers towed behind trucks (on-road). c Could result in a “jerky” connection between the tractor and the trailer and result in less drivi

35、ng comfort. d To be published. (Revision of ISO 6489-3:1992) e Under preparation. 50 mm 30 mm 50 mm 30 mm 50 mm 30 mm 41 mm 40 mm 40 mm 50 mm 50 mm 30 mm 40 mm 40 mm 50 mm 50 mm 30 mm 80 mm 30 mm BSISO56921:2004 5 Bibliography 1 ISO 1102:1986, Commercial road vehicles Mechanical connections between

36、towing vehicles and trailers 50 mm drawbar couplings 2 ISO 5692:1979, Agricultural vehicles Mechanical connections on towed vehicles Hitch-rings Specifications 3 ISO 5692-2:2002, Agricultural vehicles Mechanical connections on towed vehicles Part 2: Coupling ring 40 with socket 4 ISO 6489-1:1991, Ag

37、ricultural vehicles Mechanical connections on towing vehicles Part 1: Hook type 5 ISO 6489-1:2001, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 1: Dimensions of hitch-hooks 6 ISO 6489-2:2002, Agricultural vehicles Mechanical connections between towed and towing

38、 vehicles Part 2: Specifications for clevis coupling 40 7 ISO 6489-3: 1) , Agricultural vehicles Mechanical connections between towed and towing vehicles Part 3: Tractor drawbar 8 ISO 6489-4:2004, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 4: Dimensions of pi

39、ton-type coupling 9 ISO 8755:1986, Commercial road vehicles Mechanical connections between towing vehicles and trailers 40 mm drawbar coupling 10 ISO 20019:2001, Agricultural vehicles Mechanical connections on towed vehicles Dimensions for hitch rings 11 ISO 24347, Agricultural vehicles Mechanical c

40、onnections between towed and towing vehicles Dimensions of ball-type coupling device (80 mm) 2) 1) To be published. (Revision of ISO 6489-3:1992) 2) Under preparation. BSISO56921:2004BS ISO 5692-1:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent

41、national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they posse

42、ss the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity

43、 of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internationa

44、l and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the

45、 BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI ele

46、ctronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial

47、 discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at h

48、ttp:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free