BS ISO 5692-3-2011 Agricultural vehicles Mechanical connections on towed vehicles Swivel hitch rings《农用车辆 挂车车上的机械连接 旋转牵引环》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 5692-3:2011Agricultural vehicles Mechanical connections ontowed vehiclesPart 3: Swivel hitch ringsBS ISO 5692-3:2011 BRITISH STANDARDNational forewordThis British Standard

2、 is the UK implementation of ISO 5692-3:2011.The UK participation in its preparation was entrusted to TechnicalCommittee AGE/6, Agricultural tractors and forestry machinery.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purp

3、ort to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 66538 7ICS 65.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandar

4、ds Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS ISO 5692-3:2011Reference numberISO 5692-3:2011(E)ISO 2011INTERNATIONAL STANDARD ISO5692-3First edition2011-07-15Agricultural vehicles Mechanical connections on towed vehicles Part 3: Swivel hitch

5、 rings Vhicules agricoles Liaisons mcaniques sur vhicules remorqus Partie 3: Anneaux dattelage rotatifs BS ISO 5692-3:2011ISO 5692-3:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or

6、 by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E

7、-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 5692-3:2011ISO 5692-3:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bod

8、ies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

9、 non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,

10、Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies cast

11、ing a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5692-3 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agri

12、culture and forestry, Subcommittee SC 4, Tractors. ISO 5692 consists of the following parts, under the general title Agricultural vehicles Mechanical connections on towed vehicles: Part 1: Dimensions for hitch rings of 50/30 mm cross section Part 2: Coupling ring 40 with socket Part 3: Swivel hitch

13、rings BS ISO 5692-3:2011BS ISO 5692-3:2011INTERNATIONAL STANDARD ISO 5692-3:2011(E) ISO 2011 All rights reserved 1Agricultural vehicles Mechanical connections on towed vehicles Part 3: Swivel hitch rings 1 Scope This part of ISO 5692 specifies the requirements for hitch rings used for the attachment

14、 of agricultural trailers and implements to the rear of self-propelled agricultural vehicles equipped with a non-swivel clevis coupling as specified in ISO 6489-5. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references,

15、only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6489-5:2011, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 5: Specifications for non-swivel clevis couplings 3 Terms and

16、 definitions For the purposes of this document, the following terms and definitions apply. 3.1 D value D mathematically established representative force for the horizontal component of the force acting on the coupling in the longitudinal axis of the machine NOTE It is expressed in kilonewtons (kN).

17、3.2 vertical load on the coupling point S load transmitted, under static conditions, on the reference centre of the mechanical coupling NOTE It is expressed in kilograms (kg). BS ISO 5692-3:2011ISO 5692-3:2011(E) 2 ISO 2011 All rights reserved4 Interchangeability dimensions 4.1 General Hitch ring di

18、mensions shall be as shown in Figure 1 or 2 and as specified in Table 1. Allowable loads are indicated in Table 1. F = d + 2h NOTE Dimensions are given in Table 1. NOTE Dimensions are given in Table 1. Figure 1 Cylindrical eye configuration Figure 2 Round eye configuration Table 1 Shapes, dimensions

19、 and allowable loads Coupling ring mm Cylindrical eye configuration Round eye configuration d b c e i h d1t d b c e i t h Vertical load S kg D value D kN Shape 0,5 min. min. max. max. 1 3 min. 0,5 min. min. max. max. min. 1u1 000 u35 W 28 50 80 30 30 20 70 44 22 40 80 30 30 44 20u2 000 u90 X 45 70 1

20、00 40 32 105 63 35 50 100 40 63 30u3 000 u120 Y 62 90 120 60 55 40 132 73 50 55 140 60 55 73 35u3 000 u120 Z 73 100 140 75 60 42 157 78 68 60 160 75 60 78 424.2 Trailer shank travel angles When the trailer shank, fitted with the specified hitch ring, is fixed to the towing vehicle, the shank shall b

21、e free to turn so that the angles formed with the horizontal situated in the towing vehicles plane of symmetry and passing through the coupling point have the following minimum values. BS ISO 5692-3:2011ISO 5692-3:2011(E) ISO 2011 All rights reserved 3a) Angle of yaw: rotation around a vertical axis

22、 passing through the coupling point, with a minimum value of 60 on both sides (see Figure 3). b) Angle of pitch: rotation around a horizontal axis passing through the coupling point and perpendicular to the machines longitudinal plane of symmetry, with a minimum value of 20 top and bottom (see Figur

23、e 4). Allowance should be made for the towing machine being up to 3 from horizontal, due to front/rear tyre sizes. c) Angle of roll: rotation around a horizontal axis passing through the coupling point and located in the machines plane of symmetry, with a minimum value of 20 top and bottom (see Figu

24、re 5). Figure 3 Angle of yaw Figure 4 Angle of pitch BS ISO 5692-3:2011ISO 5692-3:2011(E) 4 ISO 2011 All rights reservedFigure 5 Angle of roll 5 Constructional requirements Hitch rings in accordance with this part of ISO 5692 shall be substantially toroidal or cylindrical and shall be manufactured b

25、y forging. The removable hitch ring shall be jointed to a sleeve fixed on the trailer drawbar. 6 Permissible mechanical connections between rings and couplings The permissible mechanical connections between rings and couplings are given in Table 2. Table 2 Permissible mechanical connections between

26、rings and couplings Ring Coupling ISO 5692-3 Shape W ISO 6489-5 Shape w ISO 5692-3 Shape X ISO 6489-5 Shape x ISO 5692-3 Shape Y ISO 6489-5 Shape y ISO 5692-3 Shape Z ISO 6489-5 Shape z 7 Marking The swivel hitch ring shall have a permanent and visible ring shape letter marking for identification. B

27、S ISO 5692-3:2011ISO 5692-3:2011(E) ISO 2011 All rights reserved 5Annex A (informative) Recommended mechanical connection combinations between towing and towed vehicles Towing vehicle Towed vehicle ISO 6489-1:1991, hook type ISO 5692:1979/ISO 5692-1:2004, hitch ring (50 mm hole centre, 30 mm ring di

28、ameter) ISO 5692:1979/ISO 5692-1:2004, hitch ring (50 mm hole centre, 30 mm ring diameter) ISO 6489-1:2001, hook typeaISO 20019:2001, hitch ring (50 mm hole centre, 30 to 41 mm ring diameter)ISO 5692-2:2002, coupling ring (40 mm socket) ISO 8755:1986, 40 mm drawbar couplingbISO 6489-2:2002, bolt typ

29、e ISO 1102:1986, 50 mm drawbar couplingbISO 6489-4:2004, piton type ISO 5692:1979/ISO 5692-1:2004, hitch ring (50 mm hole centre, 30 mm ring diameter) ISO 6489-5:2011, non-swivel clevis coupling ISO 5692-3:2011, swivel hitch rings ISO 24347:2005, ball type ISO 24347 (80 mm ball diameter) Only these

30、combinations are recommended. a Connecting an ISO 6489-1:2001 hook, manufactured in accordance with the maximum sizes permitted, to hitch rings in accordance with ISO 5692-1 and of minimum dimensions (30 mm ring diameter) according to ISO 20019 could result in a “jerky” connection between the tracto

31、r and the trailer and less driving comfort. bPrimarily used on trailers towed behind trucks (on-road). BS ISO 5692-3:2011ISO 5692-3:2011(E) 6 ISO 2011 All rights reservedBibliography 1 ISO 1102:1986, Commercial road vehicles Mechanical connections between towing vehicles and trailers 50 mm drawbar c

32、ouplings 2 ISO 5692:1979, Agricultural vehicles Mechanical connections on towed vehicles Hitch-rings Specifications 3 ISO 5692-1:2004, Agricultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for hitch rings of 50/30 mm cross section 4 ISO 5692-2:2002, Agricultural vehicles

33、Mechanical connections on towed vehicles Part 2: Coupling ring 40 with socket 5 ISO 6489-1:1991, Agricultural vehicles Mechanical connections on towing vehicles Part 1: Hook type 6 ISO 6489-1:2001, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 1: Dimensions of h

34、itch-hooks 7 ISO 6489-2:2002, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 2: Specifications for clevis coupling 40 8 ISO 6489-4:2004, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 4: Dimensions of piton-type coupling 9 ISO

35、 8755:1986, Commercial road vehicles Mechanical connections between towing vehicles and trailers 40 mm drawbar coupling 10 ISO 20019:2001, Agricultural vehicles Mechanical connections on towed vehicles Dimensions for hitch rings 11 ISO 24347:2005, Agricultural vehicles Mechanical connections between

36、 towed and towing vehicles Dimensions of ball-type coupling device (80 mm) BS ISO 5692-3:2011BS ISO 5692-3:2011ISO 5692-3:2011(E) ICS 65.060.10 Price based on 6 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British

37、Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road L

38、ondon W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be g

39、rateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual upda

40、ting service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addi

41、tion all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publi

42、shedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are

43、also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefi

44、ts contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. B

45、SI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopyin

46、g, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: