BS ISO 5745-2004 Pliers and nippers - Pliers for gripping and manipulating - Dimensions and test values《夹扭钳和剪切钳 夹扭钳 尺寸和试验值》.pdf

1、BRITISH STANDARD BS ISO 5745:2004 Pliers and nippers Pliers for gripping and manipulating Dimensions and test values ICS 25.140.30 BS ISO 5745:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 9 December 2004 BSI 9 December 2004 ISBN 0 580

2、 45039 2 National foreword This British Standard reproduces verbatim ISO 5745:2004 and implements it as the UK national standard. It supersedes BS 3087-5:1986 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MTE/15, Hand tools, to Subcommittee MTE/15/1

3、3, Assembly tools for screws and nuts, pliers and nippers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this docu

4、ment may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract.

5、 Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for ch

6、ange, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 10, an inside back cover and a back cover. Th

7、e BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 5745:2004(E) OSI 4002INTERNATIONAL STANDARD ISO 5745 Third edition 2004-09-15 Pliers and nippers Pliers for gripping and mani

8、pulating Dimensions and test values Pinces et tenailles Pinces de serrage et de manipulation Dimensions et valeurs dessai BSISO5745:2004IS:5475 O4002(E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu sla

9、hl ton ide ebtlnu deess the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera

10、 Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb

11、ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 4002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na yby mnae,s lecetrin

12、oc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh repmissii non writign from ietI rehSa Ot tsserdda eh below or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o

13、gr We bwww.is.o gro Pulbisdehi n Switlrez dnaii ISO 4002 Allr ithgsr esedevrBSISO5745:2004IS:5475 O4002(E) I SO 4002 All irthgs ersedevr iiiContents Page Foreword iv 1 Scope 1 2 Normative references. 1 3 Dimensions and test values. 1 4 Designation 8 5 Marking. 9 Bibliography . 10 BSISO5745:2004IS:54

14、75 O4002(E) iv I SO 4002 All irthgs ersedevrForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each membe

15、r body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Elec

16、trotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopt

17、ed by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of paten

18、t rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5745 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This third edition cancels and replaces the second edition (ISO

19、5745:1988) which has been technically revised. BSISO5745:2004INTENRATIONAL TSANDADR IS:5475 O4002(E)I SO 4002 All irthgs ersedevr 1Pliers and nippers Pliers for gripping and manipulating Dimensions and test values 1 Scope This International Standard specifies the principal dimensions of pliers for g

20、ripping and manipulating and the test values for the pliers in order to verify their aptitude to function in conformity with ISO 5744. General technical requirements are given in ISO 5743. The pliers for gripping and manipulating illustrated in this International Standard are examples only and are n

21、ot intended to affect the manufacturers design. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

22、 amendments) applies. ISO 5743, Pliers and nippers General technical requirements ISO 5744:2004, Pliers and nippers Methods of test 3 Dimensions and test values 3.1 Round nose pliers for gripping and manipulating The principal dimensions for round nose pliers for gripping and manipulating are shown

23、in Figure 1 and given in Table 1. Round nose pliers shall be tested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 2. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. BSISO5745:20

24、04IS:5475 O4002(E) 2 I SO 4002 All irthgs ersedevrDimensions in millimetres aF = Load applied in load test. Figure 1 Round nose pliers for gripping and manipulating Table 1 Round nose pliers for gripping and manipulating, principal dimensions Dimensions in millimetres l l 3d 1w 3t Length of nose max

25、. max. max. 125 6,3 0 5 25 2 16 9 140 8 0 6,3 32 2,8 18 10 Short nose 160 8 0 8 40 3,2 20 11 140 7 40 4 2,8 17 9 160 8 50 5 3,2 19 10 Long nose 180 9 63 6,3 3,6 20 11 BSISO5745:2004IS:5475 O4002(E) I SO 4002 All irthgs ersedevr 3Table 2 Round nose pliers for gripping and manipulating, torsion and lo

26、ad test values Torsion test Load test Length of nose Nominal length l l 1TorqueT Maximum twist maxLoad F Maximum permanent set s max amm mm N m N mm 125 63 0,5 630 140 71 1,0 710 Short nose 160 80 1,25 20 800 140 63 0,25 630 160 71 0,5 710 Long nose 180 80 1,0 25 800 1 as = w 1 w 2(see ISO 5744). 3.

27、2 Flat nose pliers for gripping and manipulating The principal dimensions of flat nose pliers for gripping and manipulating are shown in Figure 2 and given in Table 3. Flat nose pliers shall be tested in accordance with ISO 5744. Dimensions in millimetres aThe head may be tapered over the length l 3

28、 . bF = Load applied in load test. Figure 2 Flat nose pliers for gripping and manipulating BSISO5745:2004IS:5475 O4002(E) 4 I SO 4002 All irthgs ersedevrTable 3 Flat nose pliers for gripping and manipulating, principal dimensions Dimensions in millimetres l l 3w 3w 4t 1Length of nose max. max. max.

29、125 6 0 5 25 16 3,2 9 140 7 0 6,3 32 18 4 10 Short nose 160 8 0 8 40 20 5 11 140 7 40 4 16 3,2 9 160 8 50 5 18 4 10 Long nose 180 9 63 6,3 20 5 11 After the load test, the permanent set s shall not exceed the value given in Table 4. If distance l 1is not suitable for the load test, the formula given

30、 in ISO 5744:2004, 4.2 shall be used. Table 4 Flat nose pliers for gripping and manipulating, torsion and load test values Torsion test Load test Nominal length l l 1TorqueT Maximum twist maxLoad F Maximum permanent set s max aLength of nose mm mm N m N mm 125 63 4 20 630 1 140 71 5 20 710 1 Short n

31、ose 160 80 6 20 800 1 140 63 630 1 160 71 710 1 Long nose 180 80 800 1 as = w 1 w 2(see ISO 5744). 3.3 Snipe nose pliers for gripping and manipulating The principal dimensions for snipe nose pliers for gripping and manipulating are shown in Figure 3 and given in Table 5. Snipe nose pliers shall be t

32、ested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 6. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. BSISO5745:2004IS:5475 O4002(E) I SO 4002 All irthgs ersedevr 5Dimensions i

33、n millimetres aF = Load applied in load test. Figure 3 Snipe nose pliers for gripping and manipulating Table 5 Snipe nose pliers for gripping and manipulating, principal dimensions Dimensions in millimetres l l 3w 3w 4t 1t 2max. max. max. max. 140 7 40 5 16 2,5 9 2 160 8 53 6,3 19 3,2 10 2,5 180 10

34、60 8 20 5 11 3 200 10 80 10 22 5 12 4 280 14 80 14 22 5 12 4 Table 6 Snipe nose pliers for gripping and manipulating, load test values Load test Nominal length l l 1Load F Maximum permanent set s max amm mm N mm 140 63 630 1 160 71 710 1 180 80 800 1 200 90 900 1 280 140 630 1 as = w 1 w 2(see ISO 5

35、744). BSISO5745:2004IS:5475 O4002(E) 6 I SO 4002 All irthgs ersedevr3.4 Snipe nose pliers with side cutter for medium hard wire The principal dimensions for snipe nose pliers for gripping and manipulating are shown in Figure 4 and given in Table 7. Dimensions in millimetres aF = Load applied in load

36、 test or F 1force applied in cutting test. Figure 4 Snipe nose pliers with side cutter for medium hard wire Table 7 Snipe nose pliers with side cutter for medium hard wire, principal dimensions Dimensions in millimetres l l 3w 3w 4t 1t 2max. max. max. max. 140 7 40 5 16 2,5 9 2 160 8 53 6,3 19 3,2 1

37、0 2,5 180 10 60 8 20 5 11 3 200 10 80 10 22 5 12 4 Snipe nose pliers shall be tested in accordance with ISO 5744. After the load test, the permanent set s shall not exceed the value given in Table 8. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be u

38、sed. The cutting force, F 1 , and the diameter, d, of the test wire shall not exceed the values given in Table 8. Pliers having a lever ratio differing from the values given in Table 8 shall be checked for compliance using the formula given in ISO 5744:2004, 5.3.2. BSISO5745:2004IS:5475 O4002(E) I S

39、O 4002 All irthgs ersedevr 7Table 8 Snipe nose pliers with side cutter for medium hard wire, dimensions for load and force application, test values Cutting test Load test Nominal length l l 1l 2Diameter of medium hard test wire daMaximum cutting force F 1, maxLoad F Maximum permanent set s max bmm m

40、m mm mm N N mm 140 63 12,5 1,6 570 630 1 160 71 14 1,6 570 710 1 180 80 16 1,6 570 800 1 200 90 18 1,6 570 900 1 aData for medium hard test wire are given in ISO 5744. bs = w 1 w 2(see ISO 5744). 3.5 Flat nose pliers with side cutter for medium hard wire The principal dimensions for flat nose pliers

41、 for gripping and manipulating are shown in Figure 5 and given in Table 9. Flat nose pliers shall be tested in accordance with ISO 5744. Dimensions in millimetres aThe head may be tapered over length l 3 . bF = Load applied in load test or F 1force applied in cutting test. Figure 5 Flat nose pliers

42、with side cutter for medium hard wire BSISO5745:2004IS:5475 O4002(E) 8 I SO 4002 All irthgs ersedevrTable 9 Flat nose pliers with side cutter for medium hard wire, principal dimensions Dimensions in millimetres l l 3w 3w 4t 1max. max. max. 140 7 40 5 16 2,5 9 160 8 53 6,3 19 3,2 10 200 10 80 10 22 5

43、 11 After the load test, the permanent set s shall not exceed the value given in Table 10. If distance l 1is not suitable for the load test, the formula given in ISO 5744:2004, 4.2 shall be used. Pliers having a lever ratio differing form the values given in Table 10 shall be checked for compliance

44、using the formula given in ISO 5744:2004, 5.3.2. Table 10 Flat nose pliers with side cutter for medium hard wire, dimensions for load and force application, test values Cutting test Load test Nominal length l l 1l 2Diameter of medium hard test wire d aMaximum cutting force F 1, maxLoad F Maximum per

45、manent set s max bmm mm mm mm N N mm 140 63 12,5 1,6 570 630 1 160 71 14 1,6 570 710 1 200 90 18 1,6 570 900 1 aData for medium hard test wire are given in ISO 5744. bs = w 1 w 2(see ISO 5744). 4 Designation EXAMPLE 1 Round nose pliers, number 203 in accordance with ISO 5742, with a nominal length,

46、l, of 140 mm and short nose (S) are designated as follows: Round nose pliers 203 - ISO 5745 - 140 - S EXAMPLE 2 Flat nose pliers, number 201 in accordance with ISO 5742, with a nominal length, l, of 160 mm and long nose (L) are designated as follows: Flat nose pliers 201 - ISO 5745 - 160 - L EXAMPLE

47、 3 Snipe nose pliers, number 202 in accordance with ISO 5742, with a nominal length, l, of 180 mm are designated as follows: Snipe nose pliers 202 - ISO 5745 - 180 BSISO5745:2004IS:5475 O4002(E) I SO 4002 All irthgs ersedevr 9EXAMPLE 4 Snipe nose pliers, number 202 in accordance with ISO 5742, with

48、a nominal length, l, of 160 mm and with side cutter (C) are designated as follows: Snipe nose pliers 202 - ISO 5745 - 160 - C EXAMPLE 5 Flat nose pliers, number 201 in accordance with ISO 5742, with a nominal length, l, of 140 mm and with side cutter (C) are designated as follows: Flat nose pliers 201 - ISO 5745 - 140 - C 5 Marking Marking shall be in accordance with ISO 5743. BSISO5745:2004IS:5475 O4002(E) 10 I SO 4002 All irthgs ersedevrBibliography 1 ISO 5742, Pliers and nippers Nomenclature BSISO5745:2004blankBS ISO 5745:2004 BSI 389 Chiswick High Road London W