BS ISO 5751-3-2010 Motorcycle tyres and rims (metric series) Range of approved rim contours《摩托车轮胎和轮辋(公制系列) 配套轮辋轮廓范围》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 5751-3:2010Motorcycle tyres and rims(metric series)Part 3: Range of approved rim contoursBS ISO 5751-3:2010 BRITISH STANDARDNational forewordThis British Standard is the U

2、K implementation of ISO 5751-3:2010. Itsupersedes BS ISO 5751-3:2004 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AUE/4, Tyres and wheels for motor vehicles.A list of organizations represented on this committee can beobtained on request to its secret

3、ary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 67626 0ICS 43.140; 83.160.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was p

4、ublished under the authority of theStandards Policy and Strategy Committee on 30 November 2010.Amendments issued since publicationDate Text affectedBS ISO 5751-3:2010Reference numberISO 5751-3:2010(E)ISO 2010INTERNATIONAL STANDARD ISO5751-3Sixth edition2010-11-15Motorcycle tyres and rims (metric ser

5、ies) Part 3: Range of approved rim contours Pneumatiques et jantes pour motocycles (sries millimtriques) Partie 3: Gamme des profils de jante homologus BS ISO 5751-3:2010ISO 5751-3:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this f

6、ile may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretaria

7、t accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure t

8、hat the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication ma

9、y be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel.

10、 + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 5751-3:2010ISO 5751-3:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of

11、 national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Int

12、ernational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with t

13、he rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval

14、by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5751-3 was prepared by Technical Committee

15、ISO/TC 31, Tyres, rims and valves, Subcommittee SC 10, Cycle, moped, motorcycle tyres and rims. This sixth edition cancels and replaces the fifth edition (ISO 5751-3:2004), which has been technically revised. ISO 5751 consists of the following parts, under the general title Motorcycle tyres and rims

16、 (metric series): Part 1: Design guides Part 2: Tyre dimensions and load-carrying capacities Part 3: Range of approved rim contours BS ISO 5751-3:2010BS ISO 5751-3:2010INTERNATIONAL STANDARD ISO 5751-3:2010(E) ISO 2010 All rights reserved 1Motorcycle tyres and rims (metric series) Part 3: Range of a

17、pproved rim contours 1 Scope This part of ISO 5751 specifies the approved rim contours for motorcycle rims on which metric series motorcycle tyres are mounted. NOTE See ISO 4249 for motorcycle tyres and rims (code-designated series) of rim diameter codes 13 and above, and ISO 6054 for those of codes

18、 12 and below. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4249-3,

19、 Motorcycle tyres and rims (code-designated series) Part 3: Rims ISO 5751-2, Motorcycle tyres and rims (metric series) Part 2: Tyre dimensions and load-carrying capacities ISO 6054-2:1990, Motorcycle tyres and rims (Code-designated series) Diameter codes 4 to 12 Part 2: Rims 3 Approved rim contours

20、See Tables 1 and 2 for the range of permitted rims and approved rim contour codes, and for the coefficients and tyre nominal section widths used to calculate minimum and maximum rim widths. BS ISO 5751-3:2010ISO 5751-3:2010(E) 2 ISO 2010 All rights reservedTable 1 Coefficients for approved rims Coef

21、ficient, Series Tyre construction minimum, Rminmaximum, RmaxDiagonal and bias-belted 0,50 0,70 100 to 80 Radial 0,60 0,70 Diagonal and bias-belted 0,55 0,75 75 Radial 0,65 0,75 Diagonal and bias-belted 0,60 0,80 70 to 60 Radial 0,70 0,80 Diagonal and bias-belted 0,70 0,85 55 and 50 Radial 0,75 0,85

22、45 to 30 Radial 0,85 0,95 Minimum rim width = NminSRxNSMaximum rim width = NmSRawhere is the tyre nominal section width (see Table 2). Calculated values shall be rounded to the nearest standardized rim widths as specified in ISO 4249-3. The dimensions of rim contours, diameter details and complete m

23、arking of rims of nominal rim diameter shall be in accordance with ISO 4249-3 for codes 13 and above, and ISO 6054-2 for codes 12 and below. The recommended rims correspond to the measuring rim widths (Rm) specified in ISO 5751-2. The design new tyre section width, S, and the maximum overall width i

24、n service, Wmax, specified in ISO 5751-2 will change 1 mm for each 0.1 code (2,5 mm) change in rim width from the recommended (measuring) rim width. BS ISO 5751-3:2010ISO 5751-3:2010(E) ISO 2010 All rights reserved 3Table 2 Approved rim contours Tyre nominal section width NSApproved rimsabc30, 35, 4

25、0 and 45 series 210 240 250 260 280 300 330 360 MT7.00; MT7.50; MT8.00 MT8.00; MT8.50; MT9.00 MT8.50; MT9.00; MT9.50 MT8.50; MT9.00; MT9.50 MT9.50; MT10.00; MT10.50 MT10.00; MT10.50: MT11.00 MT11.00; MT11.50; MT12.00; MT12.50 MT12.00; MT12.50; MT13.00; MT13.50 55 and 50 series 130 140 150 160 170 18

26、0 190 200 210 240 MT3.75; MT4.00 MT4.00; MT4.25; MT4.50 MT4.50; MT5.00 MT4.50; MT5.00 MT5.00; MT5.50 (MT5.00); MT5.50; MT6.00 MT5.50; MT6.00 MT6.00; MT6.25; MT6.50 MT6.25; MT6.50; MT7.00 MT7.00; MT7.50; MT8.00 60, 65 and 70 series 80 100 110 120 130 140 150 160 170 180 190 200 210 230 (MT1.85); (1.8

27、5); 2.15; MT2.15; 2.50; MT2.50 (2.50); (MT2.50); 2.75; MT2.75; MT3.00 (2.50); (MT2.50); (2.75); (MT2.75); MT3.00; MT3.50 (2.75); (MT2.75); (MT3.00); MT3.50; MT3.75 (MT3.00); MT3.50; MT3.75; MT4.00 (MT3.50); MT3.75; MT4.00; MT4.25; MT4.50 (MT3.50); (MT3.75); MT4.00; MT4.25; MT4.50 (MT3.75); (MT4.00);

28、 MT4.25; MT4.50; MT5.00 (MT4.00); MT4.25; MT4.50; MT5.00; MT5.50 (MT4.25); (MT4.50); MT5.00; MT5.50 (MT4.50); MT5.00; MT5.50; MT6.00 (MT4.75); (MT5.00); MT5.50; MT6.00; MT6.25 (MT5.00); (MT5.50); MT6.00; MT6.25; MT6.50 (MT5.50); (MT6.00); MT6.25; MT6.50; MT7.00 75 series 140 (MT3.00); MT3.50; MT3.75

29、; MT4.00; MT4.75 BS ISO 5751-3:2010ISO 5751-3:2010(E) 4 ISO 2010 All rights reservedTable 2 (continued) Tyre nominal section width NSApproved rimsabc80, 90 and 100 series 50 60 70 80 90 100 110 120 130d140d150d160 170 180 1.20; 1.40 (1.20); 1.40; 1.50; MT1.50; 1.60; MT1.60 (1.40); (1.50); (MT1.50);

30、1.60; MT1.60; 1.85; MT1.85 (1.60); (MT1.60); 1.85; MT1.85; 2.15; MT2.15 (1.85); (MT1.85); 2.15; MT2.15; 2.50; MT2.50 (2.15); (MT2.15); 2.50; MT2.50; 2.75; MT2.75 (2.15); (MT2.15); 2.50; MT2.50; 2.75; MT2.75; 3.00; MT3.00 (2.50); (MT2.50); 2.75; MT2.75; 3.00; MT3.00 (2.50); (MT2.50); (2.75); (MT2.75)

31、; 3.00; MT3.00; MT3.50 (2.75); (MT2.75); (3.00); (MT3.00); MT3.50; MT3.75 (3.00); (MT3.00); MT3.50; MT3.75; MT4.00; MT4.25 (MT3.50); MT3.75; MT4.00; MT4.25; MT4.50 (MT3.50); (MT3.75); MT4.00; MT4.25; MT4.50 (MT3.50); (MT3.75); (MT4.00); MT4.25; MT4.50; MT5.00 a Recommended rims are the measuring rim

32、s. b Care should be taken, especially when either tyres or rims, or both, are not marked with the suffix M/C, not to fit motorcycle tyres to rims designed for tyres for other types of service (e.g. passenger cars or agricultural machines). Cylindrical bead-seat rims are for tube-type tyres only. c R

33、ims within parentheses are permitted for diagonal-ply and bias-belted tyres only. d For tyre sizes 130/90-16, 140/90-16 and 150/80-16, a 3.00D rim with a specified rim diameter of 405,6 mm 0,4 mm and with humps is permitted (see ISO 6054-2 for contour dimensions).BS ISO 5751-3:2010ISO 5751-3:2010(E)

34、 ISO 2010 All rights reserved 5Bibliography 1 ISO 4249-1:1985, Motorcycle tyres and rims (Code-designated series) Part 1: Tyres 2 ISO 4249-2:1990, Motorcycle tyres and rims (Code-designated series) Part 2: Tyre load ratings 3 ISO 6054-1:1994, Motorcycle tyres and rims (Code-designated series) Diamet

35、er codes 4 to 12 Part 1: Tyres BS ISO 5751-3:2010ISO 5751-3:2010(E) ICS 43.140; 83.160.10 Price based on 5 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, inf

36、ormation and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 89

37、96 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity w

38、hileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers

39、 automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign sta

40、ndards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.I

41、nformation on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products a

42、nd services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20

43、8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publicat

44、ions of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permis

45、sion from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: