BS ISO 6194-4-2009 Rotary shaft lip-type seals incorporating elastomeric sealing elements - Performance test procedures《密封件为弹性体材料的旋转轴唇形密封圈 性能试验规程》.pdf

1、BS ISO6194-4:2009ICS 23.100.60; 83.140.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRotary shaft lip-typeseals incorporatingelastomeric sealingelementsPart 4: Performance test proceduresThis British Standardwas published under theauthority of the StandardsP

2、olicy and StrategyCommittee on 30 April2009 BSI 2009ISBN 978 0 580 55229 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 6194-4:2009National forewordThis British Standard is the UK implementation of ISO 6194-4:2009. Itsupersedes BS ISO 6194-4:1999 which is withdrawn.The UK partici

3、pation in its preparation was entrusted to TechnicalCommittee MCE/11, Fluid seals and their housings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are resp

4、onsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 6194-4:2009Reference numberISO 6194-4:2009(E)ISO 2009INTERNATIONAL STANDARD ISO6194-4Third edition2009-03-15Rotary shaft lip-type seals incorporating elastomeric sealing element

5、s Part 4: Performance test procedures Bagues dtanchit lvres pour arbres tournants incorporant des lments dtanchit en lastomre Partie 4: Mthodes dessai de performance BS ISO 6194-4:2009ISO 6194-4:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing

6、policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Cent

7、ral Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been tak

8、en to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this

9、publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211

10、Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 6194-4:2009ISO 6194-4:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1

11、3 Terms, definitions and symbols 2 3.1 Terms and definitions. 2 3.2 Symbols . 2 4 Pre-test procedure 2 5 Dynamic normal-temperature test 2 5.1 Test apparatus 2 5.2 Installation . 5 5.3 Test conditions . 5 5.4 Test procedure 5 5.5 Post-test measurements 5 5.6 Recording 5 5.7 Acceptance criteria. 5 6

12、Dynamic low-temperature test 5 6.1 General. 5 6.2 Test apparatus 6 6.3 Installation . 7 6.4 Test procedure 7 6.5 Post-test measurements 7 6.6 Recording 7 6.7 Acceptance criteria. 7 7 Material testing of elastomeric components . 7 7.1 Elastomeric material requirements. 7 7.2 Density . 8 7.3 Hardness

13、8 7.4 Compression set. 8 7.5 Fluid immersion 8 7.6 Dry-heat ageing in air . 8 7.7 Stiffness at low temperature 9 7.8 Recording 9 8 Identification statement (Reference to this part of ISO 6194) . 9 Annex A (informative) Typical example of a seal test report for the dynamic test 10 Annex B (informativ

14、e) Typical example of a seal test report for the dynamic low-temperature test 13 Annex C (informative) Typical example of an elastomeric material test report. 15 Bibliography . 17 BS ISO 6194-4:2009ISO 6194-4:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Sta

15、ndardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the righ

16、t to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International

17、Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an

18、 International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6

19、194-4 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 7, Sealing devices. This third edition cancels and replaces the second edition (ISO 6194-4:1999), which has been technically revised. ISO 6194 consists of the following parts, under the general title Rotary sh

20、aft lip-type seals incorporating elastomeric sealing elements: Part 1: Nominal dimensions and tolerances Part 2: Vocabulary Part 3: Storage, handling and installation Part 4: Performance test procedures Part 5: Identification of visual imperfections BS ISO 6194-4:2009ISO 6194-4:2009(E) ISO 2009 All

21、rights reserved vIntroduction Rotary shaft lip-type seals are used to retain fluid, e.g. lubricant, in equipment where the differential pressure is relatively low. Typically, the shaft rotates, and the housing is stationary, although in some applications the shaft is stationary, and the housing rota

22、tes. Dynamic sealing is normally the result of a designed interference fit between the shaft and a flexible element incorporated in the seal. Similarly, a designed interference fit between the outside diameter of the seal, and the diameter of the housing bore, retains the seal and prevents static le

23、akage. Careful storage, handling and proper installation of all seals are necessary to avoid hazards, both prior to and during installation, which would adversely affect service life. BS ISO 6194-4:2009BS ISO 6194-4:2009INTERNATIONAL STANDARD ISO 6194-4:2009(E) ISO 2009 All rights reserved 1Rotary s

24、haft lip-type seals incorporating elastomeric sealing elements Part 4: Performance test procedures WARNING Persons using this part of ISO 6194 should be familiar with normal laboratory practice. Whilst this part of ISO 6194 does not purport to address all the safety problems, if any, associated with

25、 its application, attention is drawn to the need to employ sensible precautions while handling hot and cold fluids and equipment. It is the responsibility of the user of this part of ISO 6194 to establish appropriate safety and health practices and to ensure compliance with any national regulatory c

26、onditions. 1 Scope ISO 6194 describes seals utilizing elastomeric sealing elements. They are considered suitable for use under low-pressure conditions (see ISO 6194-1:2007, 6.1). This part of ISO 6194 specifies general test requirements for rotary shaft lip-type seals. The tests may be used for qual

27、ification purposes. NOTE ISO 6194 is complementary to ISO 16589 which covers seals incorporating thermoplastic sealing elements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For

28、 undated references, the latest edition of the referenced document (including any amendments) applies. ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tes

29、ts ISO 812, Rubber, vulcanized or thermoplastic Determination of low-temperature brittleness ISO 815-1, Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures ISO 815-2, Rubber, vulcanized or thermoplastic Determination of compression set Par

30、t 2: At low temperatures ISO 1817, Rubber, vulcanized Determination of the effect of liquids ISO 2781, Rubber, vulcanized or thermoplastic Determination of density ISO 5598, Fluid power systems and components Vocabulary ISO 6194-1:2007, Rotary shaft lip-type seals incorporating elastomeric sealing e

31、lements Part 1: Nominal dimensions and tolerances ISO 6194-2, Rotary-shaft lip-type seals incorporating elastomeric sealing elements Part 2: Vocabulary BS ISO 6194-4:2009ISO 6194-4:2009(E) 2 ISO 2009 All rights reserved3 Terms, definitions and symbols 3.1 Terms and definitions For the purposes of th

32、is document, the terms and definitions given in ISO 6194-2 and ISO 5598 and the following apply. 3.1.1 batch identifiable and traceable consignment of rubber compound of definite composition and manufactured in a single production operation 3.2 Symbols For the purposes of this document, the symbols

33、given in ISO 6194-1 apply. 4 Pre-test procedure 4.1 Inspect all seals submitted for testing for conformity to a relevant drawing or detailed specification declared by the seal manufacturer. 4.2 For seals with an elastomeric component, ensure that the seal manufacturer has stated the material designa

34、tion batch number from which the seals have been made, together with the nominal density, nominal hardness, maximum compression set value and maximum volume change after immersion in the test fluid. Where the seal is required for the low-temperature stiffness test, ensure that the seal manufacturer

35、has also stated the maximum modulus after test at the selected test temperature. Ensure that the batch of elastomer has been tested in accordance with Clause 7. 4.3 To facilitate accurate analysis of the test results, determine the following data concerning the physical characteristics of the seal a

36、nd test apparatus before testing: a) lip diameter (with spring); b) lip diameter (without spring, measured not less than 24 h after removal of spring); c) outer case mean diameter and out-of-roundness; d) shaft diameter, material hardness and surface roughness; e) housing diameter, material and surf

37、ace roughness; f) protection lip diameter, where applicable (with and without sealing lip spring fitted). 4.4 Ensure that the specified shaft eccentricity and housing off-set of the test apparatus have been incorporated. 5 Dynamic normal-temperature test 5.1 Test apparatus The test apparatus shall b

38、e similar to the typical example shown in Figure 1 and shall consist of a suitable housing for retaining the test fluid and for positioning the test seals, as well as a rotating member having a spindle mounted horizontally on suitable bearings. The design of the housing for the seal shall be in acco

39、rdance with the dimensions specified in ISO 6194-1. The housing and the rotating member shall be capable of reproducing the eccentricity and off-set specified in 4.4. BS ISO 6194-4:2009ISO 6194-4:2009(E) ISO 2009 All rights reserved 3Key 1 filler tray 2 insulation 3 drive from prime mover 4 heater b

40、and 5 cooling coil 6 seal housing 7 test seal 8 test shaft 9 test head support 10 locking ring 11 spacer ring 12 test fluid b nominal seal width D1nominal diameter of the shaft to be used with the seal D2nominal diameter of the housing bore or outer diameter of the seal Figure 1 Typical example of d

41、ynamic normal-temperature test apparatus BS ISO 6194-4:2009ISO 6194-4:2009(E) 4 ISO 2009 All rights reservedWhere it is not practicable to provide a test apparatus with the particular shaft and housing size relevant to the application, the test apparatus shall be selected from the standard sizes lis

42、ted in Table 1. The size selected shall be that nearest to the application size. Table 1 Standard shaft and housing dimensions Dimensions in millimetres Shaft diameter Housing diameter Seal width D1D2b 20 35 7 40 55 8 60 80 8 90 120 12 200 230 15 The test apparatus shall also conform to the followin

43、g additional requirements. a) The shaft shall be capable of cycling and/or maintaining the shaft speeds to within 3 %. b) The shaft shall be capable of maintaining the specified test eccentricity under dynamic conditions to within 0,03 mm throughout each test. c) The test head shall be designed and

44、constructed so as to maintain the housing bore alignment relative to the test shaft axis within 0,03 mm throughout the operating temperature range. d) The design of the test head support shall ensure minimum deformation and vibration. e) The test head and heat transfer system shall be capable of mai

45、ntaining the temperature of the test fluid within 3 C, and shall be vented to atmosphere. f) Heat shall be applied in a manner that does not subject the test fluid to high localized temperatures that could cause fluid decomposition. g) The test shaft shall have a surface that is free of helical mach

46、ine marks and shall comply with the requirements for shafts specified in ISO 6194-1. h) The test housing bore shall comply with the requirements specified in ISO 6194-1. i) The materials, surface finish and dimensions of the test shaft and test housing bore shall conform as closely as possible to th

47、e shaft and housing bore to be used in service. j) A minimum quantity of 750 cm3of test fluid shall be used. k) The level of the test fluid in the test head shall be 0,3D1to 0,5D1above the lowest point of the shaft diameter D1. l) For seal housings with inboard bearings, the test housing shall be su

48、itably relieved at the bearing supports to prevent excessive fluid pressure between the bearing and seals. m) Means shall be provided for collecting and measuring the mass of any fluid leakage from the seals during the test. n) The test head shall have a device capable of pressurizing the seal housi

49、ng to the working pressure. o) A liquid level measuring device shall be provided on the test head. BS ISO 6194-4:2009ISO 6194-4:2009(E) ISO 2009 All rights reserved 55.2 Installation 5.2.1 Thoroughly clean the test head of contaminants and extraneous matter. 5.2.2 Install the seal into the test head so that the cumulative eccentricities of the seal and the test head are known. 5.2.3 Ensure that the plane of the seal lip is perpendicular to the shaft axis, unless otherwise specifi