BS ISO 6263-2013 Hydraulic fluid power Compensated flow-control valves Mounting surfaces《液压传动 补偿式流量控制阀 安装面》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 6263:2013Hydraulic fluid power Compensated flow-controlvalves Mounting surfacesBS ISO 6263:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementa

2、tion of ISO 6263:2013. Itsupersedes BS ISO 6263:1997 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/5, Control components.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does no

3、t purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 71575 4ICS 23.100.50Compliance with a British Standard cannot confer immunity fromlegal oblig

4、ations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2013.Amendments issued since publicationDate Text affectedBS ISO 6263:2013 ISO 2013Hydraulic fluid power Compensated flow-control valves Mounting surfacesTransmissions hydraulique

5、s Rgulateurs de dbit Plan de poseINTERNATIONAL STANDARDISO6263Third edition2013-04-15Reference numberISO 6263:2013(E)BS ISO 6263:2013ISO 6263:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be

6、 reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the req

7、uester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6263:2013ISO 6263:2013(E) ISO 2013 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative reference

8、s 13 Terms and definitions . 14 Symbols 15 Tolerances . 26 Dimensions . 27 Port marking . 28 Modular stack valves 39 Working pressure 310 Identification statement (Reference to this International Standard) . 3Bibliography .20BS ISO 6263:2013ISO 6263:2013(E)ForewordISO (the International Organization

9、 for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has

10、the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Interna

11、tional Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication

12、 as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.I

13、SO 6263 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 5, Control products and components.This third edition cancels and replaces the second edition (ISO 6263:1997), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 6263:2013ISO 6263

14、:2013(E)IntroductionIn hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure with an enclosed circuit. Typical components found in such systems are hydraulic valves. The devices control flow direction, pressure, or flow rate of liquids in the enclosed cir

15、cuit. ISO 2013 All rights reserved vBS ISO 6263:2013BS ISO 6263:2013Hydraulic fluid power Compensated flow-control valves Mounting surfaces1 ScopeThis International Standard specifies the dimensions and other data relating to surfaces on which hydraulic compensated flow-control valves are mounted in

16、 order to ensure interchangeability.It applies to mounting surfaces for hydraulic compensated flow-control valves which represent current practice; they are generally applicable to industrial equipment.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in

17、this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1219-1, Fluid power systems and components Graphical symbols and circuit diagram

18、s Part 1: Graphical symbols for conventional use and data-processing applicationsISO 3601-2:2008, Fluid power systems O-rings Part 2: Housing dimensions for general applicationsISO 4401, Hydraulic fluid power Four-port directional control valves Mounting surfacesISO 5598, Fluid power systems and com

19、ponents VocabularyISO 5783, Hydraulic fluid power Code for identification of valve mounting surfaces and cartridge valve cavities3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5598 and the graphical symbols given in ISO 1219-1 apply.4 Symbols4.1 For

20、the purposes of this International Standard, the following symbols apply:a) A, B, L, P, T, and V designate ports;b) F1, F2, F3, and F4designate threaded holes for fixing screws;c) G, G1, and G2designate the location of pin holes;d) D designates the fixing screw diameter;e) rmaxdesignates mounting su

21、rface edge radius.4.2 The graphical symbols used in Tables 2, 4, 6, 8, 10, 12, 14, and 16 are in accordance with ISO 1219-1.4.3 The code system used in this International Standard is defined in ISO 5783.INTERNATIONAL STANDARD ISO 6263:2013(E) ISO 2013 All rights reserved 1BS ISO 6263:2013ISO 6263:20

22、13(E)5 Tolerances5.1 The following requirements shall be applied to the mounting surface, i.e. that area within the chain thick lines:surface roughness: see ISO 3601-2:2008, 5.1.4 and 5.2.3;surface flatness: 0,01 mm over a distance of 100 mm (see ISO 3601-2:2008, 5.1.4);tolerance for diameters of lo

23、cating pin holes: H12.5.2 With respect to the origin, the following tolerances shall be complied with along x and y axes:pin holes: 0,1 mm;screw holes: 0,1 mm;port holes: 0,2 mm.For other dimensions, see the figures.6 Dimensions6.1 Mounting surface dimensions for hydraulic compensated flow-control v

24、alves shall be selected from the figures and tables specified in 6.2 to 6.9.6.2 Mounting surface dimensions for compensated flow-control valves with main ports of 4,5 mm maximum port diameter (code: 6263-02-01-*-13) are given in Figure 1 and Table 1.6.3 Mounting surface dimensions for compensated fl

25、ow-control valves with main ports of 7,5 mm maximum port diameter (code: 6263-03-02-*-13) are given in Figure 2 and Table 3.6.4 Mounting surface dimensions for compensated flow-control valves with two main ports of 14,7 mm maximum port diameter (code: 6263-06-03-*-13) are given in Figure 3 and Table

26、 5.6.5 Mounting surface dimensions for compensated flow-control valves with three main ports of 14,7 mm maximum port diameter (code: 6263-06-04-*-13) are given in Figure 4 and Table 7.6.6 Mounting surface dimensions for compensated flow-control valves with three main ports of 17,5 mm maximum port di

27、ameter (code: 6263-07-05-*-13) are given in Figure 5 and Table 9.6.7 Mounting surface dimensions for compensated flow-control valves with three main ports of 17,5 mm maximum port diameter (code: 6263-07-06-*-13) are given in Figure 6 and Table 11.6.8 Mounting surface dimensions for compensated flow-

28、control valves with three main ports of 23,4 mm maximum port diameter (code: 6263-08-07-*-13) are given in Figure 7 and Table 13.6.9 Mounting surface dimensions for compensated flow-control valves with three main ports of 23,4 mm maximum port diameter (code: 6263-08-08-*-13) are given in Figure 8 an

29、d Table 15.7 Port marking7.1 The port symbols for compensated flow-control valves shall be selected from the tables specified in 7.2 to 7.9.2 ISO 2013 All rights reservedBS ISO 6263:2013ISO 6263:2013(E)7.2 Port symbols for compensated flow-control valves with main ports of 4,5 mm maximum port diamet

30、er (code: 6263-02-01-*-13) are given in Table 2.7.3 Port symbols for compensated flow-control valves with main ports of 7,5 mm maximum port diameter (code: 6263-03-02-*-13) are given in Table 4.7.4 Port symbols for compensated flow-control valves with two main ports of 14,7 mm maximum port diameter

31、(code: 6263-06-03-*-13) are given in Table 6.7.5 Port symbols for compensated flow-control valves with three main ports of 14,7 mm maximum port diameter (code: 6263-06-04-*-13) are given in Table 8.7.6 Port symbols for compensated flow-control valves with two main ports of 17,5 mm maximum port diame

32、ter(code: 6263-07-05-*-13) are given in Table 10.7.7 Port symbols for compensated flow-control valves with three main ports of 17,5 mm maximum port diameter(code: 6263-07-06-*-13) are given in Table 12.7.8 Port symbols for compensated flow-control valves with two main ports of 23,4 mm maximum port d

33、iameter (code: 6263-08-07-*-13) are given in Table 14.7.9 Port symbols for compensated flow-control valves with three main ports of 23,4 mm maximum port diameter (code: 6263-08-08-*-13) are given in Table 16.8 Modular stack valvesFor modular stack valves, the mounting surfaces and ports marking give

34、n in ISO 4401 shall be used.9 Working pressureFor indication of the maximum limit of the working pressure, see Note 1 in Figures 1, 2, 3, 4, 5, 6, 7, and 8.10 Identification statement (Reference to this International Standard)Use the following statement in test reports, catalogues, and sales literat

35、ure when electing to comply with this International Standard:“Mounting surface dimensions conform to ISO 6263:2013, Hydraulic fluid power Compensated flow-control valves Mounting surfaces. ” ISO 2013 All rights reserved 3BS ISO 6263:2013ISO 6263:2013(E)Dimensions in millimetresaThe minimum thread de

36、pth is 1,5 times the screw diameter, D. The recommended full thread depth is 2D + 6 mm to facilitate interchangeability of valves and to reduce the number of fixing screw lengths. The recommended engagement of fixing screw thread for ferrous mountings is 1,25D.bThe dimensions specifying the area wit

37、hin the chain thick lines are the minimum dimensions for the mounting surface. The corners of the rectangle may be radiused to a maximum radius, rmax, equal to the thread diameter of the fixing screws. Along each axis, the fixing holes are at equal distances to the mounting surface edges.cThis dimen

38、sion gives the minimum space required for a valve with this mounting surface. The dimension is also the minimum distance from centreline to centreline of two identical mounting surfaces placed on a manifold block.The valve manufacturers attention is drawn to the fact that no part of the width of the

39、 complete valve assembly shall exceed this dimension.dBlind hole in the mounting surface to accommodate the locating pin on the valves. The minimum depth is 4 mm.NOTE 1 The supplier shall stipulate the maximum working pressure for subplates and manifold blocks.NOTE 2 See Table 2 for graphical symbol

40、s.Figure 1 Mounting surface for compensated flow-control valves with main ports of 4,5 mm maximum port diameter (code: 6263-02-01-*-13)4 ISO 2013 All rights reservedBS ISO 6263:2013ISO 6263:2013(E)Table 1 DimensionsDimensions in millimetresAxisP A T B G F1F2F3F4 4,5 max. 4,5 max. 4,5 max. 4,5 max. 3

41、,4 max.M5 M5 M5 M5x 12 4,3 12 19,7 25,5 0 24 24 0y 20,25 11,25 2,25 11,25 17,75 0 -0,75 23,25 22,5Table 2 Compensated flow-control valves with main ports of 4,5 maximum port diameter (code: 6263-02-01-*-13)Option according to ISO 5783 0 1Description Internal drain External drainCompensated flow-cont

42、rol valve with two main portsCompensated flow-control valve with by-pass check valve with two main portsCompensated flow-control valve with three main ports ISO 2013 All rights reserved 5BS ISO 6263:2013ISO 6263:2013(E)Dimensions in millimetresaThe minimum thread depth is 1,5 times the screw diamete

43、r, D. The recommended full thread depth is 2D + 6 mm to facilitate interchangeability of valves and to reduce the number of fixing screw lengths. The recommended engagement of fixing screw thread for ferrous mountings is 1,25D.bThe dimensions specifying the area within the chain thick lines are the

44、minimum dimensions for the mounting surface. The corners of the rectangle may be radiused to a maximum radius, rmax, equal to the thread diameter of the fixing screws. Along each axis, the fixing holes are at equal distances to the mounting surface edges.cThis dimension gives the minimum space requi

45、red for a valve with this mounting surface. The dimension is also the minimum distance from centreline to centreline of two identical mounting surfaces placed on a manifold block.The valve manufacturers attention is drawn to the fact that no part of the width of the complete valve assembly shall exc

46、eed this dimension.dBlind hole in the mounting surface to accommodate the locating pin on the valves. The minimum depth is 4 mm.NOTE 1 The supplier shall stipulate the maximum working pressure for subplates and manifold blocks.NOTE 2 See Table 4 for graphical symbols.Figure 2 Mounting surface for co

47、mpensated flow-control valves with main ports of 7,5 mm maximum port diameter (code: 6263-03-02-*-13)6 ISO 2013 All rights reservedBS ISO 6263:2013ISO 6263:2013(E)Table 3 DimensionsDimensions in millimetresAxisP A T B G F1F2F3F4 7,5 max. 7,5 max. 7,5 max. 7,5 max. 4 M5 M5 M5 M5x 21,5 12,7 21,5 30,2

48、33 0 40,5 40,5 0y 25,9 15,5 5,1 15,5 31,75 0 -0,75 31,75 31Table 4 Compensated flow-control valves with main ports of 7,5 maximum port diameter (code: 6263-03-02-*-13)Option according to ISO 5783 0 1Description Internal drain External drainCompensated flow-control valve with two main portsCompensate

49、d flow-control valve with by-pass check valve with two main portsCompensated flow-control valve with three main ports ISO 2013 All rights reserved 7BS ISO 6263:2013ISO 6263:2013(E)Dimensions in millimetresaThe minimum thread depth is 1,5 times the screw diameter, D. The recommended full thread depth is 2D + 6 mm to facilitate interchangeability of valves and to reduce the number of fixing screw lengths. The recommended engagement of fixing screw thread for ferrous mountings is 1,25D