BS ISO 6279-2017 Plain bearings Aluminium alloys for solid bearings《滑动轴承 实心轴承用铝合金》.pdf

1、BS ISO 6279:2017Plain bearings Aluminiumalloys for solid bearingsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 6279:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6279:2017. It supersedes BS ISO 6279:2006 which is

2、 withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/12, Plain bearings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Us

3、ers are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 92855 0 ICS 21.100.10; 77.120.10; 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was publish

4、ed under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6279:2017 ISO 2017Plain bearings Aluminium alloys for solid bearingsPaliers lisses Alliages daluminium pour paliers massifsINTERNATI

5、ONAL STANDARDISO6279Third edition2017-03Reference numberISO 6279:2017(E)BS ISO 6279:2017ISO 6279:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or util

6、ized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyrigh

7、t officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6279:2017ISO 6279:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Composition and mechanical properties 14.1 Composition

8、14.2 Mechanical properties 15 Test methods . 16 Designation 2 ISO 2017 All rights reserved iiiContents PageBS ISO 6279:2017ISO 6279:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparin

9、g International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liai

10、son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Dir

11、ectives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility tha

12、t some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent de

13、clarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to confor

14、mity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/123, Plain bearings, Subcommittee SC

15、2, Materials and lubricants, their properties, characteristics, test methods and testing conditions.This third edition cancels and replaces the second edition (ISO 6279:2006), which has been technically revised.iv ISO 2017 All rights reservedBS ISO 6279:2017INTERNATIONAL STANDARD ISO 6279:2017(E)Pla

16、in bearings Aluminium alloys for solid bearings1 ScopeThis document specifies the composition and properties of preferred cast aluminium alloys for use in solid plain bearings. Other alloys can be specified with agreement between the manufacturer and user.2 Normative referencesThe following document

17、s are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4384-2, Plain be

18、arings Hardness testing of bearing metals Part 2: Solid materials3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedi

19、a .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 Composition and mechanical properties4.1 CompositionPreferred compositions are given in Table 1.Methods of analysis shall be mutually agreed between the manufacturer and user.4.2 Mechanical propertiesMechanical propert

20、ies are given in Table 1.Tensile strength and elongation are mandatory properties that are the subject of quality control checks carried out by the material manufacturers.Hardness is a mandatory property that may be checked on individual bearings.Typical values of other properties are given for desi

21、gn guidance.5 Test methodsThe tensile test shall be carried out as agreed between the manufacturer and user.Test methods and mandatory values shall be agreed between the manufacturer and user.Hardness testing shall be carried out in accordance with ISO 4384-2. ISO 2017 All rights reserved 1BS ISO 62

22、79:2017ISO 6279:2017(E)Table 1 Aluminium alloysAluminium alloyAlSn6Cu AlSn6CuNi AlSn20Cu AlZn4,5SiCuMg AlZn5SiCuMg AlSi12CuMgNiChemical composition (mass fraction in %)Chemical elementAl Remainder Remainder Remainder Remainder Remainder RemainderSn 5,5 to 6,5 5,5 to 7 17,5 to 22,5 0,2 max. 0,2 max.

23、Cu 1,3 to 1,7 0,7 to 1,3 0,7 to 1,3 0,9 to 1,2 0,9 to 1,2 0,8 to 1,5Ni 0,2 max. 0,7 to 1,3 0,2 max. 0,2 max. 1,3 max.Si 0,3 max. 0,7 max. 0,7 max. 1,0 to 2,0 1,2 to 2,0 11,0 to 13,0Fe 0,4 max. 0,7 max. 0,7 max. 0,4 max. 0,6 max. 0,7 max.Mn 0,2 max. 0,1 max. 0,7 max. 0,3 max. 0,3 max. 0,3 max.Zn 0,2

24、max. 4,4 to 5,0 5,0 to 5,5 0,3 max.Mg 0,1 max. 0,4 to 0,6 0,4 to 0,6 0,8 to 1,3Ti 0,05 to 0,2 0,2 max. 0,02 to 0,15 0,02 to 0,15 0,2 max.Total other elements, max.0,5 0,5 0,5 0,5 0,5 0,5Mechanical propertiesHardness Brinell HB10/1 000/1035 to 40 35 to 45 30 to 55 48 to 56 50 to 60 90 to 120Tensile s

25、trength RmMPa130 to 140 110 to 140 110 to 130 160 to 200 180 to 220 200 to 250Elongation A %30 to 36 10 to 20 28 to 32 20 to 22 19 to 21 0,3 to 0,80,2 % Proof stress Rp0,2MPa50 to 60 45 to 60 40 to 60 80 to 110 100 to 120 190 to 230Elastic modulus E GPa 69 71 63 75 75 75Thermal expansion 106/K 23 23

26、 24 23 23 21Thermal conductivity W/(m K) 160 160 155 170 170 184Density 103kg/m32,9 2,9 3,12 2,9 2,9 2,76 DesignationThe designation shall include the following information, in the order given:a) “Aluminium alloy”;b) reference to this document, i.e. ISO 6279;c) name of alloy.EXAMPLE The aluminium al

27、loy AlSn6Cu is designated by the following:Aluminium alloy ISO 6279 AlSn6Cu2 ISO 2017 All rights reservedBS ISO 6279:2017BS ISO 6279:2017ISO 6279:2017(E) ISO 2017 All rights reservedICS 77.150.10; 21.100.10Price based on 2 pagesThis page deliberately left blankBSI is the national body responsible fo

28、r preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, in

29、dustry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all si

30、zes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge

31、Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Orga

32、nizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the internation

33、al standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly

34、display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The

35、 standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchase

36、d in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can s

37、ave money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further i

38、nformation on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with stan

39、dards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your st

40、andards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. Wi

41、th updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your

42、business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20