BS ISO 6415-2005 Internal combustion engines - Spin-on filters for lubricating oil - Dimensions《内燃机 润滑油用旋压式过滤器 尺寸》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58oil DimensionsICS 43.060.30Internal combustion engines Spin-on filters for lubricating BRITISH STAN

2、DARDBS ISO 6415:2005BS ISO 6415:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 5 December 2005 BSI 5 December 2005ISBN 0 580 46282 Xrequest to its secretary.Cross-referencesThe British Standards which implement international publications

3、 referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary p

4、rovisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, p

5、ages 1 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this subcommittee can be obtained on present to the responsible international/E

6、uropean committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard reproduces verbatim ISO 6415:2005 and implements it as the UK n

7、ational standard. It supersedes BS 7403-13:1991 which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee MCE/21, Filters for gases and liquids, to Subcommittee MCE/21/5, Filters for lubricating oil, which has the responsibility to: aid enquirers to understand t

8、he text;Reference numberISO 6415:2005(E)INTERNATIONAL STANDARD ISO6415Third edition2005-06-01Internal combustion engines Spin-on filters for lubricating oil Dimensions Moteurs combustion interne Filtres huile visss Dimensions BS ISO 6415:2005ii iiiForeword ISO (the International Organization for Sta

9、ndardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the righ

10、t to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International

11、Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an

12、 International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6

13、415 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection equipment and filters for use on road vehicles. This third edition cancels and replaces the second edition (ISO 6415:1990), which has been technically revised. BS ISO 6415:2005blank1Internal combustion eng

14、ines Spin-on filters for lubricating oil Dimensions 1 Scope This International Standard specifies the essential dimensions necessary for interchangeability of spin-on filters of the full-flow type for the filtration of lubricating oil for internal combustion engines. It also gives the designation an

15、d marking of these filters. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

16、. ISO 68 (all parts), ISO general purpose screw threads Basic profile ISO 261, ISO general purpose metric screw threads General plan ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 965-3, ISO general purpose metric screw threads Tolerances Part 3:

17、 Deviations for constructional screw threads 3 Requirements 3.1 Connection thread and sealing surface The dimensions of the male and female connection threads and of the sealing surface are specified in Figure 1 and Table 1. The thread shall conform to ISO 68, ISO 261, ISO 965-1 and ISO 965-3. The s

18、ealing surface shall be continuous and free from porosity and nicks. NOTE The use of filters with unified threads is discouraged to avoid the danger of mismatching. BS ISO 6415:20052 Dimensions in millimetres unless otherwise specified aMinimum clearance = filter diameter K + 20 mm bSealing surface

19、Ra = 3,2 m. Mean value measured at minimum wave length C = 0,8 mm and the overall distance lm= 4 mm cSocket sizes 1 and 2: 0,2. Socket sizes 3 and 4: 0,3. Figure 1 Connection and sealing surface Table 1 Dimensions of connection threads and sealing surface Dimensions in millimetres Connection thread

20、Sealing surface d1Tolerance e d2d3h1h2Socket size stud thread afilter thread min. max. max. min. min. min. 0 M20x1,5 6g 6H 14 20 54 69 2 2 1 M20x1,5 6g 6H 14 20 58 76 2 2 2 M26x2 6g 6H 14 20 58 76 2 2 3 M30x2 6g 6H 16 22 90 113 4 2 4 M38x2 6g 6H 16 22 90 113 4 2 aThe stud shall be threaded over full

21、 distance e. When the filter has been tightened, at least three full threads shall be in contact. NOTE M16 1,5 and M24 1,5 have been reserved for spin-on fuel filters. BS ISO 6415:200533.2 Filter diameter and length The maximum dimensions for filter diameter and length are specified in Figure 2 and

22、Table 2. aFree gasket height at discretion of manufacturer, depending on material and shape. The gasket shall have sufficient compression to allow satisfactory fitting; once fitted, it shall provide a satisfactory seal during the life of the filter. bThe gasket diameter shall be included within the

23、diameters d2/d3. cFilter and gasket diameter shall be so joined as to necessitate the replacement of both parts simultaneously. Figure 2 Filter Table 2 Filter dimensions Dimensions in millimetres Diameter K u 80 80 90 100 112 u 90 u 100 u 112 u 140 Length Lmax125 160 210 265 310 0 x 1 x x x x 2 x x

24、3 x x x Socket size 4 x x BS ISO 6415:20054 3.3 By-pass valve For equipment protection, each spin-on filter type shall be fitted with a by-pass valve or an equivalent device unless a by-pass valve has been incorporated in the engine design. By-pass valves fitted to the spin-on filter shall operate a

25、t one of the following pressures: 100 kPA 20 kPA 160 kPa 30 kPa 250 kPa 40 kPa 3.4 Design of canister base In order to facilitate removal and installation of the filter, the canister base shall incorporate one of the following features: a curved surface, i.e. without any impressions, as specified in

26、 Figure 3, type X; grooves as specified in Figure 4, type Y; flats as specified in Figure 5, type Z. 4 Designation Spin-on filters for lubricating oil shall be designated in accordance with the following example. EXAMPLE Designation of a spin-on filter with metric thread M20 1,5 and socket size 1: O

27、il filter ISO 6415 M20 x 1,5 - 1 In order to use the ISO designation in the marking as specified in Clause 5, the filter shall conform to all requirements given in this International Standard. Figure 3 Canister base type X Without impressions BS ISO 6415:20055Dimensions in millimetres Figure 4 Canis

28、ter base type Y Without grooves Number of grooves: 6 or multiple of 6 Dimensions in millimetres Figure 5 Canister base type Z With flats Number of flats: 8, 10, 12, 14, 15 or more 5 Marking WARNING In view of the current wide use of unified threads, a note should also be given in publicity literatur

29、e and on filter cartons and filter assembles wherever metric threads are used, to avoid mismatching. Each spin-on filter shall be marked with the following information: a) name of manufacturer or supplier; b) type designation (for example, catalogue number); c) date or code of manufacture; d) instru

30、ctions for installation; e) ISO designation (see Clause 4). The full marking shall appear on each filter body unless the engine manufacturer dictates otherwise. BS ISO 6415:2005BS ISO BSI389 Chiswick High RoadLondonW4 4AL6415:2005BSI British Standards InstitutionBSI is the independent national body

31、responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest am

32、endments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be

33、found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standa

34、rds publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation o

35、f those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information ser

36、vices are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purcha

37、se price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information

38、 about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract

39、 may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols

40、, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.