BS ISO 6489-4-2007 Agricultural vehicles - Mechanical connections between towed and towing vehicles - Dimensions of piton-type coupling《农用车辆 被牵引与牵引车之间的机械连接装置 测定楔式耦合尺寸》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58towed and towing vehicles Part 4: Dimensions of piton-type couplingICS 65.060.01; 65.060.10Agricult

2、ural vehicles Mechanical connections between BRITISH STANDARDBS ISO 6489-4:2004BS ISO 6489-4:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 580 50434 1Amendments issued since publicationAmd. No. Date Comm

3、entscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 6489-4:2004.The UK participation in its preparation was en

4、trusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery.A list of organizations represented on AGE/6 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 6489-4:2004(E)INTERNATIONAL S

5、TANDARD ISO6489-4First edition2004-02-15Agricultural vehicles Mechanical connections between towed and towing vehicles Part 4: Dimensions of piton-type coupling Vhicules agricoles Liaisons mcaniques entre vhicules remorqueurs et vhicules remorqus Partie 4: Dimensions des dispositifs dattelage de typ

6、e piton BS ISO 6489-4:2004ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter

7、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

8、 Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the te

9、chnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS

10、O shall not be held responsible for identifying any or all such patent rights. ISO 6489-4 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. ISO 6489 consists of the following parts, under the general title Agricultural ve

11、hicles Mechanical connections between towed and towing vehicles: Part 1: Dimensions of hitch-hooks Part 2: Specifications for clevis coupling 40 Part 3: Tractor drawbar Part 4: Dimensions of piton-type coupling BS ISO 6489-4:2004blank1Agricultural vehicles Mechanical connections between towed and to

12、wing vehicles Part 4: Dimensions of piton-type coupling 1 Scope This part of ISO 6489 specifies the dimensional requirements for the piton-type coupling devices used in the attachment to agricultural towing vehicles of towed, non-balanced trailers and implements equipped with a coupling ring specifi

13、ed in ISO 5692-1. Its purpose is to ensure the interchangeability of the mechanical connections on agricultural towing vehicles. It is applicable only in those cases where the vertical static load does not exceed 30 kN. 2 Normative references The following referenced documents are indispensable for

14、the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 500 (all parts), Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 ISO 5692-1:1), Agr

15、icultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for hitch-rings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 piton-type coupling device coupling device consisting of a pin (see Figure 1), mounting part and ke

16、eper 3.2 mounting part part needed to mount the pin and the keeper to an agricultural vehicle or to its mounting frame 3.3 keeper part that prevents unintentional uncoupling of the hitch-ring 1) To be published. (Revision of ISO 5692:1979) BS ISO 6489-4:20042 4 Dimensions 4.1 The keeper location and

17、 piton-type coupling device dimensions shall be in accordance with Figures 1 and 2. The keeper shall be contained within the maximum metal outline. 4.2 No part of the keeper shall be allowed to extend beyond the hatched clearance lines (maximum metal condition illustrated) shown in Figure 2. 4.3 The

18、 manufacturer is responsible for both the design and the manufacturing quality of the piton-type coupling device. In order to prevent unintentional uncoupling of the hitch-ring when subjected to the maximum design load, the distance between the top of the pin and the keeper shall not exceed 10 mm (s

19、ee Figure 2). 4.4 The yaw requirement of 60 according to ISO 5692-1 is applicable for the device. Large tyres and narrow track settings on the towing vehicle can restrict this angle in service: when smaller tyres and/or wide track settings are used on the towing vehicle, this angle may be exceeded.

20、As this could result in interference, it should be indicated on a decal or decals on or near the assembly, and in the operators manual. Dimensions in millimetres Figure 1 Dimensions of pin 5 Location 5.1 The location of the piton-type coupling device shall be in accordance with Figure 3. 5.2 In orde

21、r to allow for the travel angles defined in ISO 5692-1, the location of the piton-type coupling device shall be in accordance with the following: a) the piton-type coupling device shall be mounted in the plane of the tractor longitudinal axis; b) the pin shall be located as high as possible, without

22、 any part of the pin-type coupling or its construction, keeper-plate, etc. entering the clearance zone specified for the PTO (power take-off) according to ISO 500. BS ISO 6489-4:20043Dimensions in millimetres Figure 2 Dimensions of keeper limiting surface (maximum metal) BS ISO 6489-4:20044 a 50 mm

23、to 160 mm.Figure 3 Pin PTO relations BS ISO 6489-4:20045Annex A (informative) Recommended mechanical connection combinations between towing and towed vehicles Towing vehicle Towed vehicle ISO 6489-1:1991 hook type ISO 5692:1979/ISO 5692-1: chitch-ring (50 mm hole centre, 30 mm ring diameter) ISO 569

24、2:1979/ISO 5692-1: chitch-ring (50 mm hole centre, 30 mm ring diameter) ISO 6489-1:2001 hook type aISO 20019:2001 hitch-ring (50 mm hole centre, 30 mm to 41 mm ring diameter) ISO 5692-2:2002 coupling ring (40 mm socket) ISO 8755:1986 40 mm drawbar coupling bISO 6489-2:2002 bolt type ISO 1102:1986 50

25、 mm drawbar coupling bISO 6489-4:2004 piton type ISO 5692:1979/ISO 5692-1: chitch-ring (50 mm hole centre, 30 mm ring diameter) ISO 24347 ball type ISO 24347 d(80 mm ball diameter) Only these combinations are recommended. aConnecting a ISO 6489-1:2001 hook, manufactured in accordance with the maximu

26、m sizes permitted, to hitch-rings in accordance with ISO 5692-1 and of minimum dimensions (30 mm ring diameter) according to ISO 20019 could result in a “jerky” connection between the tractor and the trailer and result in less driving comfort. bPrimarily used on trailers towed behind trucks (on-road

27、). cTo be published. (Revision of ISO 5692:1979) dUnder preparation. BS ISO 6489-4:20046 Bibliography 1 ISO 1102:1986, Commercial road vehicles Mechanical connections between towing vehicles and trailers 50 mm drawbar couplings 2 ISO 5692:1979, Agricultural vehicles Mechanical connections on towed v

28、ehicles Hitch-rings Specifications 3 ISO 5692-2:2002, Agricultural vehicles Mechanical connections on towed vehicles Part 2: Coupling ring 40 with socket 4 ISO 6489-1:1991, Agricultural vehicles Mechanical connections on towing vehicles Part 1: Hook type 5 ISO 6489-1:2001, Agricultural vehicles Mech

29、anical connections between towed and towing vehicles Part 1: Dimensions of hitch-hooks 6 ISO 6489-2:2002, Agricultural vehicles Mechanical connections between towed and towing vehicles Part 2: Specifications for clevis coupling 40 7 ISO 8755:1986, Commercial road vehicles Mechanical connections betw

30、een towing vehicles and trailers 40 mm drawbar coupling 8 ISO 20019:2001, Agricultural vehicles Mechanical connections on towed vehicles Dimensions for hitch-rings 9 ISO 24347, Agricultural vehicles Mechanical connections between towed and towing vehicles Dimensions of ball-type coupling device (80

31、mm)2)2) Under preparation. BS ISO 6489-4:2004blankBS ISO BSI389 Chiswick High RoadLondonW4 4AL6489-4:2004BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. I

32、t is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful

33、if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating

34、 service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersb

35、si-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide

36、 range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20

37、8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. F

38、ax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also ho

39、lds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recordi

40、ng or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.