BS ISO 6986-2013 Side and face milling (slotting) cutters with indexable inserts Dimensions《带可转位刀片的三面刃铣刀(开槽) 尺寸》.pdf

1、BSI Standards PublicationBS ISO 6986:2013Side and face milling (slotting)cutters with indexable inserts DimensionsBS ISO 6986:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6986:2013. It supersedes BS4193-12:1984 which is withdrawn.The UK participation in

2、 its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Use

3、rs are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 81023 7ICS 25.100.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of

4、 the Standards Policy and Strategy Committee on 30 September 2013.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6986:2013 ISO 2013Side and face milling (slotting) cutters with indexable inserts DimensionsFraises trois tailles plaquettes amovibles DimensionsINTERNAT

5、IONAL STANDARDISO6986Second edition2013-09-01Reference numberISO 6986:2013(E)BS ISO 6986:2013ISO 6986:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any

6、 form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale

7、56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6986:2013ISO 6986:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 1Annex A (informative) Relationship

8、between designations in this International Standard and ISO 13399 (all parts) 3Bibliography 4BS ISO 6986:2013ISO 6986:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Internationa

9、l Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO,

10、also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1

11、. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements o

12、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www

13、.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This second

14、edition cancels and replaces the first edition (ISO 6986:1983), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 6986:2013INTERNATIONAL STANDARD ISO 6986:2013(E)Side and face milling (slotting) cutters with indexable inserts Dimensions1 ScopeThis International Standard

15、specifies the dimensions of side and face milling (slotting) cutters with indexable inserts.The shape and dimensions of the inserts are left to the discretion of the manufacturer.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are i

16、ndispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 240, Milling cutters Interchangeability dimensions for cutter arbors or cutter mandrels3 DimensionsSee

17、Figure 1 and Table 1.aThe value of 90 is the nominal cutting edge angle of the insert.Figure 1 Dimensions ISO 2013 All rights reserved 1BS ISO 6986:2013ISO 6986:2013(E)Table 1 DimensionsDimensions in millimetresdjs16d1bH7d2min.ll102+80 27 41 10 10100 32 4710 1012 12125 40 5512 1216 16160 40 5516 162

18、0 20200 50 6920 2025 25bThe dimensions of the bore and key shall be in accordance with ISO 240.2 ISO 2013 All rights reservedBS ISO 6986:2013ISO 6986:2013(E)Annex A (informative) Relationship between designations in this International Standard and ISO 13399 (all parts)For the relationship between de

19、signations in this International Standard and preferred symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship between designations in this International Standard and the ISO 13399 seriesSymbol in this Inter-national Standard (ISO 6986)Reference in this International Standar

20、d (ISO 6986)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesReference in the ISO 13399 seriesdFigure 1 and Table 1Cutting diameter DCISO/TS 13399-3 71D084653E57Fd1Figure 1 and Table 1Connection diameter DCONISO/TS 13399-3 71EBDBF5060E6d2Figure 1 and Table 1Hub diameter DHUBISO/TS

21、13399-3 71D087D3B17B0lFigure 1 and Table 1Cutting width CWISO/TS 13399-3 71CEAEBE2B825l1Figure 1 and Table 1Hub thickness THUBISO/TS 13399-3 71D087D3F5E0790 Figure 1 Tool cutting edge angle KAPRISO/TS 13399-3 71D078F683C9B ISO 2013 All rights reserved 3BS ISO 6986:2013ISO 6986:2013(E)Bibliography1 I

22、SO 13399 (all parts), Cutting tool data representation and exchange4 ISO 2013 All rights reservedBS ISO 6986:2013BS ISO 6986:2013ISO 6986:2013(E) ISO 2013 All rights reservedICS 25.100.20Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British

23、 Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4A

24、L UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open con

25、sultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contactin

26、g our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign stand

27、ards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (B

28、SOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price

29、 of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a

30、 BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your docu

31、mentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard

32、 or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the int

33、ernational standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electro

34、nic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW