BS ISO 7368-2016 Hydraulic fluid power Two-port slip-in cartridge valves Cavities《液压传动 二油口盖板式插装阀 插装孔》.pdf

1、BS ISO 7368:2016Hydraulic fluid power Two-port slip-in cartridge valves CavitiesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 7368:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7368:2016. It supersedes BS 7296-1:

2、1990 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/5, Control components.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions

3、 of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 87177 1ICS 23.100.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published unde

4、r the authority of theStandards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publication Date Text affectedBS ISO 7368:2016 ISO 2016Hydraulic fluid power Two-port slip-in cartridge valves CavitiesTransmissions hydrauliques Distributeurs cartouche, bride, deux

5、 orifices LogementsINTERNATIONAL STANDARDISO7368Second edition2016-08-01Reference numberISO 7368:2016(E)BS ISO 7368:2016ISO 7368:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publi

6、cation may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the count

7、ry of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 7368:2016ISO 7368:2016(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 1

8、5 Tolerances . 26 Dimensions . 27 Identification statement (Reference of this International Standard) . 3Bibliography .36 ISO 2016 All rights reserved iiiContents PageBS ISO 7368:2016ISO 7368:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nationa

9、l standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internation

10、al organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended f

11、or its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.o

12、rg/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be

13、 in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions

14、related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 131, Fluid power systems,

15、 Subcommittee SC 5, Control products and components.This second edition cancels and replaces the first edition (ISO 7368:1989), which has been technically revised.This edition includes the following significant changes with respect to the previous edition: New sizes 15 and 16 are introduced; Surface

16、 tolerances for sealing purposes are aligned with ISO 3601-2.iv ISO 2016 All rights reservedBS ISO 7368:2016ISO 7368:2016(E)IntroductionIn hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Typical components found in such s

17、ystems are hydraulic valves. These devices control flow direction, pressure or flow rate of liquids in the enclosed circuit. ISO 2016 All rights reserved vBS ISO 7368:2016BS ISO 7368:2016Hydraulic fluid power Two-port slip-in cartridge valves Cavities1 ScopeThis document specifies only geometrical d

18、ata relating to cavities in which two-port hydraulic slip-in cartridge valves are mounted in order to ensure interchangeability.NOTE For example, this document does not specify rated pressures.It applies to cavities for two-port hydraulic slip-in cartridge valves which are generally applicable to in

19、dustrial equipment.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced d

20、ocument (including any amendments) applies.ISO 1302, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentationISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 3601-2, Fluid

21、power systems O-rings Part 2: Housing dimensions for general applicationsISO 4287, Geometrical Product Specifications (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters3 Terms and definitionsFor the purposes of this document, the terms and definitions given in IS

22、O 5598 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Symbolsa) A, B, X, Y, Z1and Z2identify ports the operational

23、 usage of which, in some cases, may be different from that given in the following examples:1) A: inlet, service, return corresponding to the placing in the hydraulic circuit;2) B: inlet, service, return corresponding to the placing in the hydraulic circuit;3) X: pilot, inlet;4) Y: pilot, return;INTE

24、RNATIONAL STANDARD ISO 7368:2016(E) ISO 2016 All rights reserved 1BS ISO 7368:2016ISO 7368:2016(E)5) Z1: supplementary pilot, inlet;6) Z2: supplementary pilot, return;b) F1 F12identify threaded holes for fixing screws;c) G, G1and G2identify the location of pin holes;d) D identifies the fixing screw

25、diameter;e) rmaxidentifies the mounting surface edge radius;f) R1indicates the maximum radius at the bottom of d1.The code system used in this document is defined in ISO 5783.NOTE Size 15 and size 16 are not yet listed in ISO 5783.5 TolerancesThe following requirements shall be applied to the sealin

26、g and chamfer surfaces, i.e. that area within the chain lines: surface roughness (see ISO 3601-2); surface roughness, Rz: as indicated on the figures according to ISO 1302 and ISO 4287; all non-specified surface finishes: Rz 63; surface roughness values are given in micrometres (m); surface flatness

27、: 0,01 mm over a distance of 100 mm (see ISO 3601-2).The following tolerances shall be complied with along the x, y and z axes with respect to the origin: pin holes: 0,2 mm; screw holes: 0,2 mm; port holes: 0,2 mm; general tolerances according to ISO 2768-1 for linear and angular dimensions without

28、tolerances.As for other dimensions, see Figure 1 to Figure 16.6 Dimensions6.1 Cavity dimensions for hydraulic slip-in cartridge valves with two main ports shall be selected from Figure 1 to Figure 16 and Table 1 to Table 16 as specified in 6.2 to 6.17.6.2 Cavity dimensions for all types of valves, e

29、xcept main system pressure-relief valves, with main ports of 16 mm nominal diameter (size 06) (code 7368 - 06 - 1 - 1 - 16) are specified in Table 1 and shown in Figure 1.6.3 Cavity dimensions for main system pressure-relief valves with main ports of 16 mm nominal diameter (size 06) (code 7368 - 06

30、- 2 - 1 - 16) are specified in Table 2 and shown in Figure 2.6.4 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 25 mm nominal diameter (size 08) (code 7368 - 08 - 3 - 1 - 16) are specified in Table 3 and shown in Figure 3.2 ISO 2016 All right

31、s reservedBS ISO 7368:2016ISO 7368:2016(E)6.5 Cavity dimensions for main system pressure-relief valves with main ports of 25 mm nominal diameter (size 08) (code 7368 - 08 - 4 - 1 - 16) are specified in Table 4 and shown in Figure 4.6.6 Cavity dimensions for all types of valves, except main system pr

32、essure-relief valves, with main ports of 32 mm nominal diameter (size 09) (code 7368 - 09 - 5 - 1 - 16) are specified in Table 5 and shown in Figure 5.6.7 Cavity dimensions for main system pressure-relief valves with main ports of 32 mm nominal diameter (size 09) (code 7368 - 09 - 6 - 1 - 16) are sp

33、ecified in Table 6 and shown in Figure 6.6.8 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 40 mm nominal diameter (size 10) (code 7368 - 10 - 7 - 1 - 16) are specified in Table 7 and shown in Figure 7.6.9 Cavity dimensions for main system pr

34、essure-relief valves with main ports of 40 mm nominal diameter (size 10) (code 7368 - 10 - 8 - 1 - 16) are specified in Table 8 and shown in Figure 8.6.10 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 50 mm nominal diameter (size 11) (code 7

35、368 - 11 - 9 - 1 - 16) are specified in Table 9 and shown in Figure 9.6.11 Cavity dimensions for main system pressure-relief valves with main ports of 50 mm nominal diameter (size 11) (code 7368 - 11 - 10 - 1 - 16) are specified in Table 10 and shown in Figure 10.6.12 Cavity dimensions for all types

36、 of valves, except main system pressure-relief valves, with main ports of 63 mm nominal diameter (size 12) (code 7368 - 12 - 11 - 1 - 16) are specified in Table 11 and shown in Figure 11.6.13 Cavity dimensions for main system pressure-relief valves with main ports of 63 mm nominal diameter (size 12)

37、 (code 7368 - 12 - 12 - 1 - 16) are specified in Table 12 and shown in Figure 12.6.14 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 80 mm nominal diameter (size 13) (code 7368 - 13 - 13 - 1 - 16) are specified in Table 13 and shown in Figure

38、 13.6.15 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 100 mm nominal diameter (size 14) (code 7368 - 14 - 14 - 1 - 16) are specified in Table 14 and shown in Figure 14.6.16 Cavity dimensions for all types of valves, except main system press

39、ure-relief valves, with main ports of 125 mm nominal diameter (size 15) (code 7368 - 15 - 15 - 1 - 16) are specified in Table 15 and shown in Figure 15.6.17 Cavity dimensions for all types of valves, except main system pressure-relief valves, with main ports of 160 mm nominal diameter (size 16) (cod

40、e 7368 - 16 - 16 - 1 - 16) are specified in Table 16 and shown in Figure 16.7 Identification statement (Reference of this International Standard)Use the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard:“Cavity dimensions co

41、nform to ISO 7368, Hydraulic fluid power Two-port slip-in cartridge valves Cavities.” ISO 2016 All rights reserved 3BS ISO 7368:2016ISO 7368:2016(E)Dimensions and geometrical tolerances in millimetresKeyaThe dimension specifying the area within the chain lines is the minimum dimension for mounting t

42、he cartridge valve cover. The corners of the square may be rounded to a maximum radius, rmax, equal to the thread diameter of the fixing screws. Along each axis, the fixing holes are at equal distances to the valve cover mounting surface edges.bPilot valves and adjustment devices may exceed this dim

43、ension.cThis dimension gives the minimum space required for a two-port hydraulic slip-in cartridge valve and its cover with this cavity. The dimension is also the minimum distance from centreline to centreline of two identical cavities on a manifold. The valve manufacturers attention is drawn to the

44、 fact that no part of the complete valve assembly shall exceed this dimension.dNo burrs permitted in this area; the edges shall be rounded.eVisual examination.fMinimum length over which the specified surface finish shall apply.Figure 1 Cavity for two-port hydraulic slip-in cartridge valves of all ty

45、pes, except main system pressure-relief valves, with main ports of 16 mm nominal diameter (size 06) and square flange cover (code: 7368 - 06 - 1 - 1 - 16)4 ISO 2016 All rights reservedBS ISO 7368:2016ISO 7368:2016(E)Table 1 Cavity for two-port hydraulic slip-in cartridge valves of all types, except

46、main system pressure-relief valves, with main ports of 16 mm nominal diameter (size 06) and square flange coverDimensions in millimetresAxisd1ed2ed3cd4b,cXcYcZ1cZ2cF1aF2aF3aF4aGd,eR1 32 H7 25 H7 16 max. 16 4 max. 4 max. 4 max. 4 max.M8 M8 M8 M8 4 H13max. R 2x 23 23 23 2 48 23 23 0 46 46 0 12,5 y 23

47、23 23 23 23 2 48 0 0 46 46 0 z 43 0,2 56 + 0,1 8 min. aThe minimum thread depth is 1,8 times the screw diameter, D. The recommended full thread depth is 2D + 6 mm to facilitate interchangeability of valves and to reduce the number of fixing screw lengths. However, sufficient distance from fixing hol

48、e to port B shall be respected. The recommended engagement of fixing screw thread for ferrous mounting is 1,25D.bSuggested diameter of port B, but may be of any size located within the space between the dimensions indicated as 20 mm and 42,5 mm; port B is not necessarily machined and may be provided

49、 by casting.cThe depth and angle of the pilot ports and the main ports are determined by the graphical layout of the hydraulic circuit and by the location of the valves in the manifold.dBlind hole to accommodate the locating pin on the valve cover.eThe depth of d1, d2and G are given in the tables as dimension z. ISO 2016 All rights reserved 5BS ISO 7368:2016ISO 7368:2016(E)Dimensions and geometrical tolerances in millimetresKeyaThe dimension specify