BS ISO 7718-1-2016 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Main deck doors《航空器 乘客登机桥或机场摆渡车连接用客舱门接口.pdf

1、BS ISO 7718-1:2016Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehiclePart 1: Main deck doorsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 7718-1:2016 BRITISH STANDARDNational forewordThis

2、British Standard is the UK implementation of ISO 7718-1:2016. It supersedes BS ISO 7718-1:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air Cargo Figure 1 has been modified; in 4.3, minimum aircraft door sill height was increased from 1,

3、60 m (63 in) to 1,80 m (71 in); and additional editorial changes have been made, such as by adding a table of contents.A list of all parts in the ISO 7718 series can be found on the ISO website.BS ISO 7718-1:2016 ISO 7718-1:2016(E) iv ISO 2016 All rights reservedBS ISO 7718-1:2016 ISO 7718-1:2016(E)

4、IntroductionThis document specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors on the outer skin of civil transport aircraft, applicable when these doors are designed to accept the connection of existing passenger boarding bridges or transfer vehicles

5、.Throughout this document, the minimum essential criteria are identified by the keyword “shall”. Recommended criteria are identified by the keyword “should” and, while not mandatory, are considered to be of primary importance in providing easily and economically handled aircraft, as well as preventi

6、ng damage to the aircraft caused by the passenger boarding bridge or transfer vehicle. Deviation from recommended criteria can only occur, after careful consideration, if positively required by basic aircraft-design factors with a significant operational cost impact. ISO 2016 All rights reserved vBS

7、 ISO 7718-1:2016Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Part 1: Main deck doors1 ScopeThis document specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors of future types

8、of civil-passenger transport aircraft when they are intended to be compatible with the thousands of passenger boarding bridges and passenger transfer vehicles existing, or being planned, in airports worldwide.This document is not applicable to existing models of civil transport aircraft, or derivati

9、ve models with entry into service up to year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expected to be compatible with ISO 16004.It is not the intent of this document to restrict in any way the basic design of an

10、y future types of civil-passenger transport aircraft. However, it aims at clarifying, for aircraft-design engineers, the design characteristics which would make it difficult or impossible for a new type of aircraft to adequately connect with existing airport passenger boarding bridges or passenger t

11、ransfer vehicles. If basic aircraft-design requirements impose on a future model certain dimensional characteristics not complying with this document, note that: either alternative methods of embarking/disembarking passengers will need to be implemented, such as integral aircraft stairs, etc.; or ex

12、isting passenger boarding bridges and/or passenger transfer vehicles in the airports where such a new type of aircraft is to operate will require some degree of modification/reworking; or additional interface devices/equipment will be required in order to connect such a new type of aircraft with exi

13、sting passenger boarding bridges and passenger transfer vehicles.Each case results in increased aircraft-handling constraints and operating cost.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this

14、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 16004, Aircraft ground equipment Passenger boarding bridge or transfer vehicle Interface requirements with aircraft doors3 Term

15、s and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/INTERNATIONAL STANDARD BS ISO 7718-1:2016 ISO 7718-1:2016(E) ISO 2016 A

16、ll rights reserved 1 ISO Online browsing platform: available at http:/www.iso.org/obp 4 Requirements4.1 Minimum unobstructed space4.1.1 Unobstructed space shall be provided for the connection of the passenger boarding bridge or passenger transfer vehicle, as shown by the hatched area in Figure 1. Th

17、e area surrounded by the dotted line represents the opening of the bridge or vehicle.4.1.2 This area shall be kept completely clear of any external features such as aerials, drains, pitot heads, static ports, sensors, incidence probes, aerodynamic strakes, access panels, etc.4.1.3 Integral aircraft

18、stairs, which do not interfere with the connection of a passenger boarding bridge or passenger transfer vehicle, or with the aircraft when in the retracted position, are permitted in this area.4.1.4 Protrusions intended to divert rainwater away from the door opening are permitted in this area, provi

19、ded they are not deemed part of the aircrafts structural or aerodynamic integrity and they do not interfere with the deployment of the PBB canopy.Existing models of civil transport aircraft present a variety of flight-safety-sensitive items in the unobstructed area defined above. They shall be prote

20、cted against inadvertent interference by provisions built into the aircraft mating section of passenger boarding bridges or passenger transfer vehicles in accordance with ISO 16004. The no-interference areas accordingly specified on ground equipment are included in the unobstructed area defined abov

21、e for future aircraft.4.2 Minimum radius of the fuselageThe cross-sectional radius of the fuselage in any part of the area defined in Figure 1 should not be less than 1,6 m (63 in).4.3 Door-sill heightThe passenger door sill height above the ground, at any part of its excursion range during normal a

22、irport servicing/transit operations, should be between 1,8 m (71 in) and 5,4 m (213 in).BS ISO 7718-1:2016 ISO 7718-1:2016(E) 2 ISO 2016 All rights reservedBS ISO 7718-1:2016 ISO 7718-1:2016(E)Dimensions in millimetres (inches)1Key1 door sill heightDimension Maximum value Minimum value Notea 2 100 (

23、82.7) Dimension of the bridge openingb 2 850 (112.2) c 4 800 (189.0)d 500 (19.7)e 3 400 (133.8)Figure 1 Unobstructed space to be provided in the vicinity of passenger doors ISO 2016 All rights reserved 3BS ISO 7718-1:2016 ISO 7718-1:2016(E) ISO 2016 All rights reservedICS 49.100Price based on 3 page

24、sThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.

25、British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format a

26、nd refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiti

27、ng our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need

28、international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or en

29、tity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other

30、person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is lic

31、ensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use

32、only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the documen

33、t, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription se

34、rvices are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refre

35、shed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribin

36、g Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on

37、your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We cont

38、inually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20