BS ISO 7718-2-2016 Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger transfer vehicle Upper deck doors《航空器 乘客登机桥或机场摆渡车连接用客舱门接.pdf

1、BS ISO 7718-2:2016Aircraft Passenger doorsinterface requirements forconnection of passengerboarding bridge or passengertransfer vehiclePart 2: Upper deck doorsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 7718-2:2016 BRITISH STANDARDNational forewordThis Bri

2、tish Standard is the UK implementation of ISO 7718-2:2016. It supersedes BS ISO 7718-2:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air Cargo Figure 1 has been modified; additional editorial changes have been made, such as by adding a t

3、able of contents.A list of all parts in the ISO 7718 series can be found on the ISO website.iv ISO 2016 All rights reservedBS ISO 7718-2:2016ISO 7718-2:2016(E)IntroductionThis document specifies minimum dimensional and unobstructed space requirements around upper deck passenger doors on the outer sk

4、in of civil transport aircraft, applicable when these doors are designed to accept connection of existing passenger boarding bridges or transfer vehicles.Throughout this document, the minimum essential criteria are identified by use of the keyword “shall”. Recommended criteria are identified by use

5、of the keyword “should” and, while not mandatory, are considered to be of primary importance in providing easily and economically handled aircraft, as well as preventing damage to the aircraft as a result of passenger boarding bridge interference. Deviation from recommended criteria can only occur,

6、after careful consideration, if positively required by basic aircraft-design factors with a significant operational cost impact. ISO 2016 All rights reserved vBS ISO 7718-2:2016BS ISO 7718-2:2016Aircraft Passenger doors interface requirements for connection of passenger boarding bridge or passenger

7、transfer vehicle Part 2: Upper deck doors1 ScopeThis document specifies the minimum dimensional and unobstructed space requirements around future civil-passenger transport aircraft upper deck passenger doors when they are intended to be compatible with passenger boarding bridges planned in airports

8、worldwide.This document is not applicable to existing models of civil transport aircraft, or derivative models with entry into service up to year 2000 with the same fuselage, for which the aircraft-mating section of passenger boarding bridges or passenger transfer vehicles is expected to be compatib

9、le with ISO 16004. However, it is expected that the design of such aircraft types may be taken into account for design of passenger boarding bridges capable of upper deck servicing, in addition to this document.It is not the intent of this document to restrict in any way the basic design of any futu

10、re types of civil-passenger transport aircraft. It aims, however, at clarifying for aircraft design engineers the design characteristics which would make it difficult or impossible for a new type of aircraft to adequately connect with airport passenger boarding bridges. Should basic aircraft design

11、requirements impose on a future model certain dimensional characteristics not complying with this document, note that: either alternative methods of embarking/disembarking passengers will need to be implemented, such as using the internal aircraft stairs, etc.; or upper deck passenger boarding bridg

12、es in the airports where such a new type of aircraft is to operate will require some degree of modification/reworking; or additional interface devices/equipment will be required in order to connect such a new type of aircraft with existing upper deck passenger boarding bridges.Each case results in i

13、ncreased aircraft-handling constraints and operating cost.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references,

14、 the latest edition of the referenced document (including any amendments) applies.ISO 7718-1, Aircraft Passenger doors interface requirements for connection of passenger boarding bridge Part 1: Main deck doorsISO 16004, Aircraft ground equipment Passenger boarding bridge or transfer vehicle Interfac

15、e requirements with aircraft doors3 Terms and definitionsNo terms and definitions are listed in this document.INTERNATIONAL STANDARD ISO 7718-2:2016(E) ISO 2016 All rights reserved 1BS ISO 7718-2:2016ISO 7718-2:2016(E)ISO and IEC maintain terminological databases for use in standardization at the fo

16、llowing addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 Requirements4.1 Minimum unobstructed space4.1.1 Unobstructed space shall be provided for the connection of the passenger boarding bridge or passenger transf

17、er vehicle as shown by the hatched area in Figure 1. The area bound by the dotted line represents the opening of the bridge or vehicle.4.1.2 This area shall be kept completely clear of any external features such as aerials, drains, pitot heads, static ports, sensors, incidence probes, aerodynamic st

18、rakes, access panels, etc.4.1.3 Protrusions intended to divert rainwater away from the door opening are allowable in this area, provided they are not deemed part of the aircrafts structural or aerodynamic integrity and they do not interfere with the deployment of the PBB canopy.4.2 Minimum radius of

19、 the fuselageThe cross-section radius of the fuselage in any part of the area defined in Figure 1 should not be less than 1,6 m (63 in).4.3 Door sill heightThe passenger door sill height above the ground, at any part of its excursion range during normal airport servicing/transit operations, should n

20、ot exceed 8,4 m (330 in).2 ISO 2016 All rights reservedBS ISO 7718-2:2016ISO 7718-2:2016(E)Dimensions in millimetres (inches)1aedKey1 door sill heightDimension Maximum value Minimum value Notea 2 100 (82.7) Dimensions of the bridge openingb 2 850 (112.2) c 4 800 (189.0)d 300 (11.8)e 2 700 (106.3)On

21、certain existing aircraft types with upward opening door, the bridge itself may need to be higher, though the specified interface area with the fuselage remains.Figure 1 Unobstructed space to be provided in the vicinity of upper deck passenger doors4.4 Main deck bridge compatibilityWhere a passenger

22、 boarding bridge is intended to serve both upper and main deck doors, the requirements of ISO 7718-1 and ISO 16004 shall be taken into account for its design in addition to those of this document. ISO 2016 All rights reserved 3BS ISO 7718-2:2016ISO 7718-2:2016(E) ISO 2016 All rights reservedICS 49.1

23、00Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by

24、 BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled i

25、n a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about Brit

26、ish Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be

27、purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by B

28、SI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the

29、 standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in

30、soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal o

31、r internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more tha

32、n 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur r

33、ange of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its avai

34、lable 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service excl

35、usive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host sta

36、ndards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendme

37、nt or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders):

38、Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20