BS ISO 7755-1-2013 Hardmetal burrs General specifications《硬金属毛刺 一般规范》.pdf

1、BSI Standards PublicationBS ISO 7755-1:2013Hardmetal burrsPart 1: General specificationsBS ISO 7755-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7755-1:2013.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips

2、 and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Insti

3、tution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 81024 4ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2013.Amendments iss

4、ued since publicationDate Text affectedBS ISO 7755-1:2013 ISO 2013Hardmetal burrs Part 1: General specificationsFraises-limes en mtaux-durs Partie 1: Spcifications gnralesINTERNATIONAL STANDARDISO7755-1Second edition2013-08-15Reference numberISO 7755-1:2013(E)BS ISO 7755-1:2013ISO 7755-1:2013(E)ii I

5、SO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intrane

6、t, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in

7、 SwitzerlandBS ISO 7755-1:2013ISO 7755-1:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 Cutting diameter 13.2 Cylindrical shank . 23.3 Relationship between cutting diameter and shank diameter 24 Direction of flute helix and dire

8、ction of cut . 35 Designation 35.1 Explanation of the designation code 35.2 Symbols . 3Annex A (informative) Relationship between designations in this part of ISO 7755 and ISO 13399 (all parts) 6Bibliography 7BS ISO 7755-1:2013ISO 7755-1:2013(E)ForewordISO (the International Organization for Standar

9、dization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to

10、 be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used

11、 to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of

12、 the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during

13、 the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this doc

14、ument is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This second edition cancels and replaces the first edition (ISO 7755-1:1984), of which it constitutes a minor revision. The tolerances given in parentheses and shown in the first edition have

15、been deleted from Table 1; also, the shank diameters 3,15 mm and 6,3 mm, which had been accepted during the transitional period, have been deleted.ISO 7755 consists of the following parts, under the general title Hardmetal burrs: Part 1: General specifications Part 2: Cylindrical burrs (style A) Par

16、t 3: Cylindrical round- (ball-) nose burrs (style C) Part 4: Spherical burrs (style D) Part 5: Oval burrs (style E) Part 6: Arch round- (ball-) nose burrs (style F) Part 7: Arch pointed-nose burrs (style G) Part 8: Flame burrs (style H) Part 9: 60 and 90 cone burrs (styles J and K) Part 10: Conical

17、round- (ball-) nose burrs (style L) Part 11: Conical pointed-nose burrs (style M) Part 12: Inverted cone burrs (style N)iv ISO 2013 All rights reservedBS ISO 7755-1:2013INTERNATIONAL STANDARD ISO 7755-1:2013(E)Hardmetal burrs Part 1: General specifications1 ScopeThis part of ISO 7755 specifies the c

18、ommon characteristics of hardmetal burrs of various styles, in solid design or with brazed shank.The main dimensions of the cutting part of hardmetal burrs are dealt with individually in ISO 7755-2, ISO 7755-3, ISO 7755-4, ISO 7755-5, ISO 7755-6, ISO 7755-7, ISO 7755-8, ISO 7755-9, ISO 7755-10, ISO

19、7755-11 and ISO 7755-12.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

20、nt (including any amendments) applies.ISO 7755-2, Hardmetal burrs Part 2: Cylindrical burrs (style A)ISO 7755-3, Hardmetal burrs Part 3: Cylindrical round- (ball-) nose burrs (style C)ISO 7755-4, Hardmetal burrs Part 4: Spherical burrs (style D)ISO 7755-5, Hardmetal burrs Part 5: Oval burrs (style E

21、)ISO 7755-6, Hardmetal burrs Part 6: Arch round- (ball-) nose burrs (style F)ISO 7755-7, Hardmetal burrs Part 7: Arch pointed-nose burrs (style G)ISO 7755-8, Hardmetal burrs Part 8: Flame burrs (style H)ISO 7755-9, Hardmetal burrs Part 9: 60 degrees and 90 degrees cone burrs (styles J and K)ISO 7755

22、-10, Hardmetal burrs Part 10: Conical round- (ball-) nose burrs (style L)ISO 7755-11, Hardmetal burrs Part 11: Conical pointed-nose burrs (style M)ISO 7755-12, Hardmetal burrs Part 12: Inverted cone burrs (style N)3 Dimensions3.1 Cutting diameterTable 1 gives the series of cutting diameters and thei

23、r related tolerances. The main dimensions of the cutting part of hardmetal burrs are specified individually in ISO 7755-2, ISO 7755-3, ISO 7755-4, ISO 7755-5, ISO 7755-6, ISO 7755-7, ISO 7755-8, ISO 7755-9, ISO 7755-10, ISO 7755-11 and ISO 7755-12. ISO 2013 All rights reserved 1BS ISO 7755-1:2013ISO

24、 7755-1:2013(E)Table 1 Cutting diameters and related tolerancesDimensions in millimetresCutting diameter Tolerance2 0,1346810 0,21216 0,33.2 Cylindrical shankShank diameter shall be 3 mm and 6 mm, with tolerance h9. Shank length shall be in accordance wtih Table 2. The shank length is defined as the

25、 length of the burr minus the length of the cutting part as given in ISO 7755-2, ISO 7755-3, ISO 7755-4, ISO 7755-5, ISO 7755-6, ISO 7755-7, ISO 7755-8, ISO 7755-9, ISO 7755-10, ISO 7755-11 and ISO 7755-12.NOTE These length ranges permit manufacture both of burrs with constant overall length and var

26、iable shank length, and of burrs with constant shank length and variable overall length. In the latter case, national standards are intended to indicate the agreed shank length.The agreed shank length shall be within the limits given in Table 2.Table 2 Shank diameter and lengthDimensions in millimet

27、resShank diameter Shank length3 20 to 356 25 to 503.3 Relationship between cutting diameter and shank diameterTable 3 gives the possible combinations of cutting diameters and shank diameters.Table 3 Cutting diameters and shank diametersDimensions in millimetresCutting diameterShank diameter3 62 3 4

28、6 8 10 12 16 2 ISO 2013 All rights reservedBS ISO 7755-1:2013ISO 7755-1:2013(E)4 Direction of flute helix and direction of cutBurrs shall have a right-hand helix and right-hand cut, unless otherwise specified.60 and 90 cone burrs (shapes J and K) may also be straight fluted.5 Designation5.1 Explanat

29、ion of the designation codeThe designation of hardmetal burrs includes six symbols, the last one being optional.The meaning of the symbols is as follows:1 letter symbol identifying the burr style (see 5.2.1);2 number symbol identifying the cutting diameter (see 5.2.2);3 number symbol identifying the

30、 cutting part length (see 5.2.3);4 letter symbol identifying the tooth type (see 5.2.4);5 number symbol identifying the shank diameter (see 5.2.5);6 number symbol identifying the shank length optional (see 5.2.6).EXAMPLE 1 2 3 4 5 6C 12 25 M 06 305.2 Symbols5.2.1 Symbol for the burr style Reference

31、1Table 4 gives the letter symbols identifying each burr style.Table 4 Letter symbols identifying burr stylesLetter symbolType IllustrationA Cylindrical burrC Cylindrical round-(ball-)nose burrD Spherical burrE Oval burr ISO 2013 All rights reserved 3BS ISO 7755-1:2013ISO 7755-1:2013(E)Letter symbolT

32、ype IllustrationF Arch round-(ball-)nose burrG Arch pointed nose burrH Flame burrJ 60 cone burrK 90 cone burrL Conical round-(ball-)nose burrM Conical pointed nose burrN Inverted cone burr5.2.2 Symbol for the cutting diameter Reference 2The number symbol is the numerical value of the cutting diamete

33、r, in millimetres. One-digit values shall be preceded by a “0” (zero).EXAMPLE 1 cutting diameter 6 mm symbol 06EXAMPLE 2 cutting diameter 12 mm symbol 125.2.3 Symbol for the cutting part length Reference 3The number symbol is the numerical value of the cutting part length, in millimetres, ignoring d

34、ecimals. One-digit values shall be preceded by a “0” (zero).EXAMPLE 1 cutting part length 5,2 mm symbol 05EXAMPLE 2 cutting part length 10 mm symbol 105.2.4 Symbol for the tooth type Reference 4Table 5 gives the letter symbols identifying each type of tooth.Table 4 (continued)4 ISO 2013 All rights r

35、eservedBS ISO 7755-1:2013ISO 7755-1:2013(E)Table 5 Letter symbols identifying tooth typesLetter symbol Tooth typeF Fine teethM Standard (medium) teethC Coarse teethNOTE The intention is to study the number of teeth for each tooth type in the future.5.2.5 Symbol for the shank diameter Reference 5Tabl

36、e 6 gives the number symbols identifying the shank diameter.Table 6 Number symbols identifying shank diametersDimensions in millimetresNumber symbol Shank diameter03 306 65.2.6 Symbol for the shank length Reference 6The optional number symbol is the numerical value of the shank length, in millimetre

37、s, ignoring decimals. ISO 2013 All rights reserved 5BS ISO 7755-1:2013ISO 7755-1:2013(E)Annex A (informative) Relationship between designations in this part of ISO 7755 and ISO 13399 (all parts)For the relationship between designations in this part of ISO 7755 and preferred symbols according to the

38、ISO 13399 series, see Table A.1.Table A.1 Relationship between designations in this part of ISO 7755 and the ISO 13399 seriesSymbol in this part of ISO 7755 (ISO 7755-1)Reference in this part of ISO 7755 (ISO 7755-1)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesReference in the

39、ISO 13399 series 5.2.1 Burr type code BTC ISO/TS 13399-3 71DF1523869EE 5.2.2 Cutting diameter DC ISO/TS 13399-3 71E57F 5.2.3 Cutting edge length L ISO/TS 13399-3 71DD6C95DA49B 5.2.5 Connection diameter DCON ISO/TS 13399-3 71EBDBF5060E6 5.2.6 Shank length LS ISO/TS 13399-3 71CF2988709466 ISO 2013 All

40、 rights reservedBS ISO 7755-1:2013ISO 7755-1:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data representation and exchange ISO 2013 All rights reserved 7BS ISO 7755-1:2013ISO 7755-1:2013(E) ISO 2013 All rights reservedICS 25.100.20Price based on 7 pagesThis page deliberately left blankBS

41、I is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)B

42、SI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled

43、 in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about Br

44、itish Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also b

45、e purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our

46、subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments

47、 and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyr

48、e revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplie

49、d as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambigu