BS ISO 7802-2013 Metallic materials Wire Wrapping test《金属材料 线材 缠绕试验》.pdf

1、BSI Standards PublicationBS ISO 7802:2013Metallic materials Wire Wrapping testBS ISO 7802:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7802:2013. The UK participation in its preparation was entrusted to TechnicalCommittee ISE/101/2, Ductility testing.A

2、list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standar

3、ds Limited 2013ISBN 978 0 580 82937 6 ICS 77.040.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2013.Amendments issued since publicationDate T e

4、x t a f f e c t e dBS ISO 7802:2013 ISO 2013Metallic materials Wire Wrapping testMatriaux mtalliques Fils Essai denroulementINTERNATIONAL STANDARDISO7802Second edition2013-11-01Reference numberISO 7802:2013(E)BS ISO 7802:2013ISO 7802:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT

5、 ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be

6、requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 7802:2013ISO 7802:2013(E) ISO 2013 A

7、ll rights reserved iiiContents PageForeword iv1 Scope . 12 Principle 13 Test equipment. 14 Procedure. 15 Test report . 1BS ISO 7802:2013ISO 7802:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The wor

8、k of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governme

9、ntal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the

10、 ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility

11、that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent

12、 declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 164, Mechanical testing of metals, Subcommittee SC 2, Ductility testing.This

13、second edition cancels and replaces the first. edition (ISO 7802:1983), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 7802:2013INTERNATIONAL STANDARD ISO 7802:2013(E)Metallic materials Wire Wrapping test1 ScopeThis International Standard specifies a method for determ

14、ining the ability of metallic wire of diameter or thickness 0,1 mm to 10 mm inclusive, to undergo plastic deformation during wrapping.2 PrincipleThe wrapping test consists of winding a wire to a specified number of turns around a mandrel of the diameter specified in the relevant standard to form a c

15、losely wrapped helix.It may also include a specified sequence of winding and unwinding, or even rewinding.3 Test equipmentThe testing machine shall be constructed so the wire can be wound around the mandrel in a helix so that adjacent wraps of the coil are in contact. A piece of the wire to be teste

16、d may be used as the mandrel, provided it is of the specified mandrel diameter and of sufficient hardness.4 Procedure4.1 In general, the test is carried out at ambient temperature between 10 C and 35 C. Tests carried out under controlled conditions shall be made at a temperature of 23 C 5 C.4.2 With

17、out applying any torsion, wind the wire in a helix tightly around the mandrel at a constant rate not exceeding 1 wrap per second so that the adjacent wraps of the coil are in contact. If necessary, reduce the rate of wrapping to ensure that the heat generated does not affect the result of the test.4

18、.3 To ensure tight winding, a tensile stress not exceeding 5 % of the nominal tensile strength of the wire may be applied during winding.4.4 When unwinding, or unwinding and rewinding, are specified, the rate shall be sufficiently slow to prevent any rise of temperature likely to affect the result o

19、f the test. At the end of the unwinding, at least one turn shall not be unwound.4.5 The interpretation of the wrapping test is carried out according to the requirements of the relevant Standard. When these requirements are not specified, absence of cracks visible without the use of magnifying aids i

20、s considered as sufficient evidence that the test piece withstood the test. Wire with a thickness or diameter less than 0,5 mm shall be examined with approximately 10-times magnification.5 Test reportThe test report shall include the following information:a) a reference to this International Standar

21、d;b) identification of the test piece (type of material, type of coating, etc.);c) diameter or thickness of the test piece; ISO 2013 All rights reserved 1BS ISO 7802:2013ISO 7802:2013(E)d) diameter of the mandrel;e) test conditions (number of turns, or the wound length);f) test result.2 ISO 2013 All

22、 rights reservedBS ISO 7802:2013BS ISO 7802:2013ISO 7802:2013(E) ISO 2013 All rights reservedICS 77.040.10Price based on 2 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI

23、 is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovato

24、rs and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose stand

25、ards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and

26、download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered f

27、rom our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and in

28、ternational standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Sub

29、scribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-Use

30、r Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standa

31、rds and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the dat

32、a, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to

33、BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from B

34、SI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW