BS ISO 8018-2007 Tools for moulding - Guide bushes headed and locating guide bushes headed《模制工具 有头的导套和有头的定位导套》.pdf

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58bushes, headedICS 25.120.30Tools for moulding Guide bushes, headed, and locating guide BRITISH STAN

2、DARDBS ISO 8018:2007BS ISO 8018:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50193 7Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct applic

3、ation.Compliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard was published by BSI. It is the UK implementation of ISO 8018:2007. It supersedes BS 7564-4:1992 which is withdrawn.The UK participation in its preparation was entrusted to T

4、echnical Committee MTE/12, Tools for pressing and moulding.A list of organizations represented on MTE/12 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a Reference numberISO 8018:2007(E)INTERNATIONAL STANDARD ISO8018Second edi

5、tion2007-02-01Tools for moulding Guide bushes, headed, and locating guide bushes, headed Outillage de moulage Bagues de guidage, collerette et collerette avec plot de centrage BS ISO 8018:2007ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of nationa

6、l standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internation

7、al organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules

8、 given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at le

9、ast 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8018 was prepared by Technical Committee ISO/TC 29,

10、 Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (ISO 8018:1985), of which it constitutes a minor revision. In particular, the references given in Clause 2, which are not mentioned in the text, have been listed in a Bibliogr

11、aphy, and the indication of surface textures has been updated in accordance with ISO 1302:2002. BS ISO 8018:2007blank1Tools for moulding Guide bushes, headed, and locating guide bushes, headed 1 Scope This International Standard specifies the dimensions and tolerances, in millimetres, for headed gui

12、de bushes and headed locating guide bushes intended for use in moulds. 2 Dimensions 2.1 Guide bushes, headed Type A The dimensions of headed guide bushes of type A shall conform to the indications of Figure 1 and Table 1. Surface roughness values in micrometres NOTE The sketch is an example only. aC

13、hamfer and a cylindrical entry over 3 mm. bR u 0,1S. Figure 1 Guide bushes, headed Type A BS ISO 8018:20072 Table 1 Dimensions of guide bushes, headed Type A Da12 16 20 25 32 40 50 D118 22 28 32 40 50 63 D222 26 32 36 45 56 71 S 4 6 6 6 8 8 8 L1L 16 20 25 16 20 25 16 20 25 16 20 25 20 25 32 40 50 32

14、 32 32 32 40 50 32 40 50 32 40 50 32 40 50 63 80 100 63 63 63 80 80 63 80 80 63 80 100 63 80 100 80 100 125 160 200 100 100 100 125 100 100 125 a For use in exceptional cases, for instance, to prevent incorrect assembly of the upper and lower plates of the mould in relation to each other, the follow

15、ing additional values for diameter D are recommended : 11, 15, 19, 24, 30, 38 and 48BS ISO 8018:200732.2 Locating guide bushes, headed Type B The dimensions of headed locating guide bushes of type B shall conform to the indications of Figure 2 and Table 2. Surface roughness values in micrometres NOT

16、E The sketch is an example only. aChamfer and a cylindrical entry over 3 mm. bR u 0,1S. Figure 2 Locating guide bushes, headed Type B BS ISO 8018:20074 Table 2 Dimensions of locating guide bushes, headed Type B Da12 16 20 25 32 40 50 D118 22 28 32 40 50 63 D222 26 32 36 45 56 71 S 4 6 6 6 8 8 8 L1L2

17、L 20 25 32 16 20 25 20 25 32 25 32 25 32 25 32 40 50 60 32 40 50 32 32 32 32 40 40 40 40 40 40 40 50 50 71 90 112 63 80 100 40 50 40 50 63 40 63 63 50 63 63 80 100 132 170 210 125 160 200 63 63 80 80 80 80 100 100 125 100 100 125 a For use in exceptional cases, for instance, to prevent incorrect ass

18、embly of the upper and lower plates of the mould in relation to each other, the following additional values for diameter D are recommended : 11, 15, 19, 24, 30, 38 and 48.3 Designation A guide bush in accordance with this International Standard shall be designated by: a) “guide bush“; b) a reference

19、 to this International Standard; c) type of guide bush (A or B); d) its internal diameter (D); e) its length (L). EXAMPLE Guide bush ISO 8018 A 12 20 Guide bush ISO 8018 B 12 20 BS ISO 8018:20075Bibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in t

20、echnical product documentation 2 ISO 4957:1999, Tool steels 3 ISO 6753-2:1998, Tools for pressing and moulding Machined plates Part 2: Machined plates for moulds 4 ISO 8017, Tools for moulding Guide pillars, straight and shouldered, and locating guide pillars, shouldered BS ISO 8018:2007BS ISO BSI38

21、9 Chiswick High RoadLondonW4 4AL8018:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards ar

22、e updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Br

23、itish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automaticall

24、y receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/

25、www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international st

26、andards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing

27、 members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regar

28、ding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the interna

29、tional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This d

30、oes not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.