BS ISO 8040-2001 Optics and optical instruments - Microscopes - Dimensions of tube slide and tube slot connections《光学和光学仪器 显微镜 镜筒导板和镜筒槽连接件尺寸》.pdf

1、BRITISH STANDARD BS ISO 8040:2001 Optics and optical instruments Microscopes Dimensions of tube slide and tube slot connections ICS 37.020 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 8040:2001 This British Standard, having been prepared under the direction of the Sec

2、tor Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 May 2001 BSI 05-2001 ISBN 0 580 37337 1 National foreword This British Standard reproduces verbatim ISO 8040:2001 and implements it as the UK national standard. It supe

3、rsedes BS 7012-5:1988 which is withdrawn The UK participation in its preparation was entrusted to Technical Committee LBI/33, Microscopes, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British

4、Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does

5、not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible

6、international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the

7、 ISO title page, pages ii to iv, pages 1 to 3 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsReference number ISO 8040:2001(E) INTERNATIONAL STANDARD ISO 8040 Second edition 20

8、01-01-15 Optics and optical instruments Microscopes Dimensions of tube slide and tube slot connections Optique et instruments doptique Microscopes Dimensions de liaison des tirettes et des logements de tiretteISO 8040:2001(E) I ii ISO 8040:2001(E)iii Foreword ISO (the International Organization for

9、Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the r

10、ight to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internation

11、al Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member b

12、odies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 8040 was prepared by Technical Committ

13、ee ISO/TC 172, Optics and optical instruments, Subcommittee SC 5, Microscopes and endoscopes. This second edition cancels and replaces the first edition (ISO 8040:1986), which has been technically revised.ISO 8040:2001(E) iv Introduction In order to produce different effects, it is common practice t

14、o use with microscopes many auxiliary devices, such as compensators and auxiliary preparations. The dimensions of tube slides and tube slots are specified in this International Standard so that auxiliary devices can become interchangeable, thus opening up the possibility of using auxiliary devices d

15、esigned for microscopes by all manufacturers.INTERNATIONAL STANDARD ISO 8040:2001(E)1 Optics and optical instruments Microscopes Dimensions of tube slide and tube slot connections 1 Scope This International Standard specifies the mechanical dimensions required for the interchange of auxiliary optics

16、 and compensators on microscopes made by all manufacturers. 2 Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of

17、these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest editions of the normative document re

18、ferred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 8576:1996, Optics and optical instruments Microscopes Reference system of polarized light microscopy. 3 Mechanical dimensions 3.1 General The dimensions of tube slides shall be as specified i

19、n 3.2 and shown in Figure 1. The dimensions of tube slots shall be as specified in 3.3 and shown in Figure 2. 3.2 Tube slides Contact springs shall be attached to the side of the tube slide, as shown in Figure 1, if the slide is equipped with optical elements requiring accurate positioning. The cont

20、act springs shall be capable of being compressed within the confines of the slide. 3.3 Tube slots Contact springs shall be attached at the top of the tube slot, as shown in Figure 2. The contact springs shall be capable of being compressed beyond the confines of the slot. The orientation of the tube

21、 slots shall be in accordance with ISO 8576.ISO 8040:2001(E) 2 Dimensions in millimetres Key 1 Contact springs Figure 1 Dimensions of the tube slidesISO 8040:2001(E)3 Dimensions in millimetres Key 1 Contact springs 2 Depth of stop groove 3 Reference surface 4 Locating surface Figure 2 Dimensions of

22、the tube slotsBS ISO 8040:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Chart

23、er. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccura

24、cy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that

25、subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.b

26、si-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international stan

27、dards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to

28、 date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-.

29、Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmit

30、ted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.