BS ISO 8051-2016 Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with recess《标称直径从M3至M10的长柄丝锥 带凹槽的直径柄丝锥》.pdf

1、BS ISO 8051:2016Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with r e c e s sBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 8051:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 8051

2、:2016. It supersedes BS ISO 8051:1999 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publica

3、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 77001 2 ICS 25.100.50 Compliance with a British Standard cannot confer immunit

4、y from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 8051:2016 ISO 2016Long shank taps with nominal diameters from M3 to M10 Full-diam

5、eter shank taps with recessTarauds machine, queue longue, de diamtre nominal M3 M10 Tarauds queue pleine, gorgeINTERNATIONAL STANDARDISO8051Third edition2016-09-15Reference numberISO 8051:2016(E)BS ISO 8051:2016ISO 8051:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Pub

6、lished in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permis

7、sion can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 8051:2016ISO 8051:2016(E)Forewor

8、d iv1 Scope . 12 Normative references 13 Dimensions . 14 Marking 2Annex A (informative) Relationship between designations in this International Standard and ISO 13399 . 3Bibliography 4 ISO 2016 All rights reserved iiiContents PageBS ISO 8051:2016ISO 8051:2016(E)ForewordISO (the International Organiz

9、ation for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

10、 has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.Th

11、e procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the e

12、ditorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent r

13、ights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an ex

14、planation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee re

15、sponsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces.This third edition cancels and replaces the second edition (ISO 8051:1999), of which it constitutes a minor revision with the following change: addition of Annex A, which gives the

16、relationship between the designations of this International Standard and the ISO 13399 series.iv ISO 2016 All rights reservedBS ISO 8051:2016INTERNATIONAL STANDARD ISO 8051:2016(E)Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with recess1 ScopeThis International Stan

17、dard specifies the dimensions for full-diameter shank taps with recess with nominal diameters from M3 to M10 and thus complements ISO 2283, which concerns relieved shank taps.It applies to long shank machine taps.Technical specifications for taps covered by this International Standard (including mar

18、king) are given in ISO 8830.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

19、cument (including any amendments) applies.ISO 529:1993, Short machine taps and hand tapsISO 8830:1991, High-speed steel machine taps with ground threads Technical specifications3 DimensionsDimensions are given in Figure 1 and Table 1.The threaded lengths of these taps are in accordance with those gi

20、ven in ISO 529.Shank lengths (L l) are increased by 50 % with respect to those given in ISO 529; total lengths therefore vary accordingly.NOTE Annex A gives the relationship between the designations of this International Standard and ISO 13399 (all parts).Figure 1 ISO 2016 All rights reserved 1BS IS

21、O 8051:2016ISO 8051:2016(E)Table 1Designation d Pitch d1l L d2al3SquareCoarse pitchesFine pitchesnom. coarse fine h9bmax. h16 min. a h11cl2 0,8M3 M3 0,35 3 0,5 0,35 3,15 11 66 2,12 18 2,55M3,5 M3,5 0,35 3,5 0,6 3,551368 2,5 20 2,8M4 M4 0,5 4 0,70,54 73 2,8213,156M4,5 M4,5 0,5 4,5 0,75 4,5 3,15 3,55M

22、5 M5 0,5 5 0,8 5 16 79 3,55 25 47 M5,5 0,5 5,5 5,6 17 84 4 26 4,5M6 M6 0,75 6 1 0,75 6,3 19 89 4,53058M7 M7 0,75 7 7,1 5,3 5,6M8 M8 1 8 1,2518 22 97 6 35 6,3 9M9 M9 1 9 9 7,1 36 7,1 10M10 M10 1101,510 24 108 7, 5 39 8 11 M10 1,25 1,25aThe recess is optional at the manufacturers discretion. If the re

23、cess is not required, such taps shall have a thread length equal to lll+()32/ .bIn accordance with ISO 237, tolerance h9 applies to precision shanks; for non-precision shanks, the tolerance is h11.cIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the squa

24、re and of its position in relation to the shank.4 MarkingMarking shall be in accordance with ISO 8830.2 ISO 2016 All rights reservedBS ISO 8051:2016ISO 8051:2016(E)Annex A (informative) Relationship between designations in this International Standard and ISO 13399For the relationship between designa

25、tions in this International Standard and preferred symbols according to ISO 13399, see Table A.1.Table A.1 Relationship between designations in this International Standard and ISO 13399Symbol in ISO 8051Reference in ISO 8051Property name in ISO 13399 seriesSymbol in ISO 13399 seriesReference in ISO

26、13399 seriesdFigure 1Table 1Thread diameter TD 71E02C5C2EED3d1Figure 1Table 1Connection diameter machine sideDCONMS 71EBDBF5060E6d2Figure 1Table 1Neck diameter DN 71EAC48EC5DE0lFigure 1Table 1Thread cutting part lengthTHL 71E02C65BB9DAl3Figure 1Table 1Usable length LU 71EBB33490FDALFigure 1Table 1Ov

27、erall length OAL 71D078EB7C086 ISO 2016 All rights reserved 3BS ISO 8051:2016ISO 8051:2016(E)Bibliography1 ISO 237, Rotating tools with parallel shanks Diameters of shanks and sizes of driving squares2 ISO 2283, Long shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in Reduced shank t

28、aps3 ISO 13399 (all parts), Cutting tool data representation and exchange4 ISO 2016 All rights reservedBS ISO 8051:2016BS ISO 8051:2016ISO 8051:2016(E) ISO 2016 All rights reservedICS 25.100.50Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing B

29、ritish Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, gover

30、nment, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and acros

31、s all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying

32、 standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, ha

33、rd copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardiz

34、ation bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the s

35、tandard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may

36、 be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard cop

37、y format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by

38、choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on

39、 our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards develop

40、ments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when

41、theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates su

42、pplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If

43、you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20