BS ISO 883-2013 Indexable hardmetal (carbide) inserts with rounded corners without fixing hole Dimensions《不带固定孔的带圆角可转位硬性金属(碳化物)镶嵌件 尺寸规格》.pdf

1、BSI Standards PublicationBS ISO 883:2013Indexable hardmetal (carbide)inserts with rounded corners,without fixing hole DimensionsBS ISO 883:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 883:2013. Itsupersedes BS 4193-2:1986 which is withdrawn.The UK parti

2、cipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contr

3、act. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 81020 6ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the author

4、ity of theStandards Policy and Strategy Committee on 30 September 2013.Amendments issued since publicationDate Text affectedBS ISO 883:2013 ISO 2013Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole DimensionsPlaquettes amovibles en mtaux-durs (carbures mtalliques) avec

5、arrondi de pointe, sans trou de fixation DimensionsINTERNATIONAL STANDARDISO883Fourth edition2013-09-01Reference numberISO 883:2013(E)BS ISO 883:2013ISO 883:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this pub

6、lication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the cou

7、ntry of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 883:2013ISO 883:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references

8、 13 Types of insert . 14 Interchangeability 14.1 Tolerances . 14.2 Thickness, s, of inserts with chip breakers . 25 Designation and marking 25.1 Designation 25.2 Marking . 26 Measurement . 27 Recommended dimensions . 27.1 General . 27.2 Triangular inserts . 37.3 Square inserts 4Annex A (informative)

9、 Tolerances for d, m and s . 7Annex B (informative) Method of measurement of “m” dimension . 8Annex C (informative) Inserts with rounded corners without fixing hole, with shapes covered by this International Standard 10Annex D (informative) Relationship between designations in this International Sta

10、ndard and ISO 13399 (all parts) .12Bibliography .13BS ISO 883:2013ISO 883:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through

11、ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates

12、 closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval crite

13、ria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent

14、 rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this

15、document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This fourth edition cancels and replaces the third editi

16、on (ISO 883:1985), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 883:2013INTERNATIONAL STANDARD ISO 883:2013(E)Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions1 ScopeThis International Standard specifies the dimensions of ind

17、exable hardmetal (carbide) inserts with rounded corners, without fixing hole and with normal clearance of 0 and 11. These inserts are primarily intended to be mounted, by top clamping, on turning and boring tools.2 Normative referencesThe following documents, in whole or in part, are normatively ref

18、erenced in this document and are indispensable to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 513, Classification and application of hard cutting materials for meta

19、l removal with defined cutting edges Designation of the main groups and groups of applicationISO 1832, Indexable inserts for cutting tools Designation3 Types of insertThe types of indexable hardmetal (carbide) inserts specified in this International Standard are the following: TN: triangular inserts

20、, with 0 normal clearance; TP: triangular inserts, with 11 normal clearance; SN: square inserts, with 0 normal clearance; SP: square inserts, with 11 normal clearance.Inserts with 0 normal clearance (TN and SN) are standardized only without chip breakers. Inserts with 11 normal clearance (TP and SP)

21、 are provided with and without chip breakers.At the time of publication, neither the shape nor the dimensions of chip breakers are standardized. Thus, if necessary, special features shall be explained by means of a diagram or additional specifications.Table C.1 gives the ranges of sizes for these in

22、serts.4 Interchangeability4.1 TolerancesIndexable hardmetal (carbide) inserts specified in this International Standard are, provided in the following tolerance classes, in accordance with ISO 1832:a) inserts without chip breakers: tolerance classes U and G;b) inserts with chip breakers: tolerance cl

23、ass M.Inserts with chip breakers and tolerance class G are second preference (see Annex C).The values of the tolerances in accordance with ISO 1832 are given in Annex A. ISO 2013 All rights reserved 1BS ISO 883:2013ISO 883:2013(E)Other tolerances are given in Tables 1 and 2.4.2 Thickness, s, of inse

24、rts with chip breakersThe thickness, s, of inserts with chip breakers is defined as the distance between the cutting edge at the corner and the opposing supporting surface of the insert; see Figure 1 a) and 1 b).a) b) Figure 15 Designation and marking5.1 DesignationThe designation of the indexable h

25、ardmetal (carbide) inserts complying with this International Standard shall conform to ISO 1832.In addition to this designation, one or both of the following may be indicated: the symbol of the group of application, in accordance with ISO 513; the commercial designation of the hardmetal (carbide) gr

26、ade.5.2 MarkingThe following synnbol, at least, shall be marked on the insert itself (except when this would be difficult on the smaller inserts): symbol of the group of application, or commercial designation of the hardmetal (carbide) grade (or both, if possible, on large inserts).6 MeasurementAnne

27、x B indicates the methods of measuring the dimension m of the indexable inserts covered by this International Standard.7 Recommended dimensions7.1 GeneralThe choice of the more common dimensions is restricted to the specifications given in Tables 1 and 2. It is strongly recommended that these standa

28、rd inserts be used wherever possible (first preference). When other inserts are specially required, insert dimensions shall be selected from the unshaded 2 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)portions/squares (blank cells) of Table C.1 (second preference). Dimensions represente

29、d by the shaded portions/squares (shaded cells) of Table C.1 are not recommended.7.2 Triangular insertsSee Figure 2, Figure 3 and Figure 4.TNUNTNGN0 normal clearance,without chip breakersFigure 2TPUNTPGN11 normal clearance,without chip breakersFigure 3 ISO 2013 All rights reserved 3BS ISO 883:2013IS

30、O 883:2013(E)TPMR11 normal clearance, with chip breakersFigure 4Table 1 Dimensions of triangular insertsDimensions in millimetresInsertldasamar 0,10TNUN 110304 TNGN 110304 TPUN 110304 TPGN 110304 TPMR 11030411,0 6,353,189,128 0,4TNUN 110308 TPUN 110308 TPMR 110308 8,731 0,8 TPUN 160304 TPMR 16030416

31、,5 9,52513,891 0,4 TPUN 160308 TPGN 160308 TPMR 160308 13,494 0,8 TPUN 160312 TPGN 160312 TPMR 160312 13,097 1,2TNUN 160408 TNGN 160408 4,7613,494 0,8TNUN 160412 TNGN 160412 13,097 1,2 TPUN 220408 22,0 12,7018,256 0,8TNUN 220412 TNGN 220412 TPUN 220412 TPGN 220412 17,859 1,2TNUN 220416 TPUN 220416 1

32、7,463 1,6a Tolerances in accordance with ISO 1832. See Annex A.7.3 Square insertsSee Figure 5, Figure 6 and Figure 7.4 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)SNUNSNGN0 normal clearance,without chip breakersFigure 5SPUNSPGN11 normal clearance,without chip breakersFigure 6 ISO 2013

33、All rights reserved 5BS ISO 883:2013ISO 883:2013(E)SPMR11 normal clearance,with chip breakersFigure 7Table 2 Dimensions of square insertsDimensions in millimetresInsert da bsamar 0,10SNUN 090304 SPUN 090304 SPMR 0903049,5253,181,808 0,4SNUN 090308 SNGN 090308 SPUN 090308 SPMR 090308 1,644 0,8 SPUN 1

34、20304 SPMR 12030412,702,466 0,4 SPUN 120308 SPGN 120308 SPMR 120308 2,301 0,8 SPUN 120312 SPGN 120312 SPMR 120312 2,137 1,2SNUN 120408 SNGN 120408 4,762,301 0,8SNUN 120412 SNGN 120412 2,137 1,2SNUN 150412 15,8752,795 1,2SNUN 150416 2,630 1,6SNUN 190412 19,053,452 1,2SNUN 190416 SPUN 190416 3,288 1,6

35、a Tolerances in accordance with ISO 1832. See Annex A.b d = l6 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)Annex A (informative) Tolerances for d, m and sNOTE This annex is an extract of ISO 1832.Table A.1 Tolerances for d, m and saDimensions in millimetresInsertTolerance for classU on

36、 G on M onDesignation d d m d m d mTN. 11.TP. 11.6,35 0,08 0,13 0,025 0,025 0,05 0,08TN. 16.TP. 16.SN. 09.SP. 09.9,525 0,08 0,13 0,025 0,025 0,05 0,08TN. 22.TP. 22.SN. 12.SP. 12.12,70 0,13 0,20 0,025 0,025 0,08 0,13SN. 15. 15,875 0,18 0,27 0,025 0,025 SN. 19.SP. 19.19,05 0,18 0,27 0,025 0,025 a Tole

37、rance for s in all tolerance classes: 0,13. ISO 2013 All rights reserved 7BS ISO 883:2013ISO 883:2013(E)Annex B (informative) Method of measurement of “m” dimensionNOTE This annex forms an integral part of this International Standard.B.1 Triangular insertsDimension m is related to the side opposite

38、the corner that is to be measured. The insert is placed on a surface plate, as shown in Figure B.1, and checked by means of a dial gauge zeroed with the aid of a gauge block corresponding to dimension m. The dial gauge then gives a direct reading of the error when applied to the inserts to be measur

39、ed.Figure B.1B.2 Square insertsDimension m is checked by reference to the diameter d of a precision roller, where d corresponds to the nominal diameter of the inscribed circle of the insert. The insert is mounted on a 90 vee-block, as shown in Figure B.2, and checked by means of a dial gauge which h

40、as been zeroed to dimension m by means of a roller with the aid of a gauge block. The dial gauge then gives a direct reading of the error when applied to the inserts to be measured. The roller has a tolerance of 0,002 mm.8 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)Figure B.2 ISO 2013

41、 All rights reserved 9BS ISO 883:2013ISO 883:2013(E)Annex C (informative) Inserts with rounded corners without fixing hole, with shapes covered by this International StandardTable C.1 Range of sizes10 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)Dimensions in millimetresdNormalclearance

42、nTolerance classUGMInsertwithout chip breakers(N)without chip breakers(N)with chip breakers on the face(R)with chip breakers on the face(R)DesignationCorner radiusrDesignationCorner radiusrDesignationCorner radiusrDesignationCorner radiusr0,40,81,21,60,40,81,21,60,40,81,21,60,40,81,21,66,350TNUN 110

43、3+TNGN 1103+9,525TNUN 1603TNGN 1603TNUN 1604+TNGN 1604+12,7TNUN 2204+TNGN 2204+6,3511TPUN 1103+TPGN 1103+TPGR 1103TPMR 1103+9,525TPUN 1603+TPGN 1603+TPGR 1603TPMR 1603+12,7TPUN 2204+TPGN 2204+TPGR 2204TPMR 22049,5250SNUN 0903+SNGN 0903+12,7SNUN 1203SNGN 1203SNUN 1204+SNGN 1204+15,875SNUN 1504+SNGN 1

44、50419,05SNUN 1904+SNGN 19049,52511SPUN 0903+SPGN 0903SPGR0903SPMR0903+12,7SPUN 1203+SPGN 1203+SPGR1203SPMR1203+15,875SPUN 1504SPGN 1504SPGR1504SPMR150419,05SPUN 1904+SPGN 1904SPGR1904SPMR1904+First preferenceinthis International Standard (see Tables1 and 2).Unshaded (blank) cells/squares: second pre

45、ference; not covered by this International Standard.Shaded cells/squares: inserts not recommended. ISO 2013 All rights reserved 11BS ISO 883:2013ISO 883:2013(E)Annex D (informative) Relationship between designations in this International Standard and ISO 13399 (all parts)For the relationship between

46、 designations in this International Standard and preferred symbols according to ISO 13399 (all parts), see Table A.1.Table D.1 Relationship between designations in this International Standard and the ISO 13399 seriesSymbol in ISO 883 (this International Standard)Reference in ISO 883 (this Interna-ti

47、onal Standard)Property name the ISO 13399 seriesSymbol the ISO 13399 seriesReference the ISO 13399 seriesd 7.2, Table 17.3, Table 2Inscribed circle diam-eterIC ISO/TS 13399-271CE7A96D9F7Dl 7.2, Table 17.3, Table 2Cutting edge length L ISO/TS 13399-271DD6C95DA49Bm 7.2, Table 17.3, Table 2m-dimension

48、M ISO/TS 13399-271CE7AA0972DBr7.2, Table 17.3, Table 2Corner radius RE ISO/TS 13399-271DD6C8ACA503s 4.27.2, Table 17.3, Table 2Insert thickness S ISO/TS 13399-271CE7A9F5308C12 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data representat

49、ion and exchange ISO 2013 All rights reserved 13BS ISO 883:2013ISO 883:2013(E) ISO 2013 All rights reservedICS 25.100.01Price based on 13 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and serv